INSTALLATIONS, PROCEDURES AND MEASURES INSTRUMENTS Sample Clauses

INSTALLATIONS, PROCEDURES AND MEASURES INSTRUMENTS. 2.1. Testing ground The test area shall be large enough to accommodate the impactor (striker) propulsion system and to permit after-collision displacement of the vehicle struck and installation of the test equipment. The part in which vehicle collision and displacement occur shall be horizontal, flat and smooth and have a coefficient of friction of not less than 0.5. 2.2. Impactor (striker) 2.2.1. The impactor shall be of steel and of rigid construction. 2.2.2. The impacting surface shall be flat, not less than 2,500 mm wide, and 800 mm high, and its edges shall be rounded to a radius of curvature of between 40 and 50 mm. It shall be clad with a layer of plywood 20 mm thick. 2.2.3. At the moment of collision the following requirements shall be met: 2.2.3.1. the impacting surface shall be vertical and perpendicular to the median longitudinal plane of the vehicle struck; 2.2.3.2. the direction of movement of the impactor shall be substantially horizontal and parallel to the median longitudinal plane of the vehicle struck; 2.2.3.3. the maximum lateral deviation tolerated between the median vertical line of the surface of the impactor and the median longitudinal plane of the vehicle struck shall be 300 mm. In addition, the impacting surface shall extend over the entire width of the vehicle struck; 2.2.3.4. the ground clearance of the lower edge of the impacting surface shall be 175 " 25 mm. 2.3. Propulsion of the impactor The impactor may either be secured to a carriage (moving barrier) or form part of a pendulum. 2.4. Special provisions applicable where a moving barrier is used 2.4.1. If the impactor is secured to a carriage (moving barrier) by a restraining element, the latter must be rigid and be incapable of being deformed by the collision; the carriage shall at the moment of collision be capable of moving freely and no longer be subject to the action of the propelling device. 2.4.2. The velocity of collision shall be between 35 and 38 km/h. 2.4.3. The aggregate weight (mass) of carriage and impactor shall be 1,100 " 20 kg 2.5. Special provisions applicable where a pendulum is used 2.5.1. The distance between the centre of the impacting face and the axis of rotation of the pendulum shall be not less than 5 m. 2.5.2. The impactor shall be freely suspended by rigid arms rigidly secured to it. The pendulum so constituted shall be substantially incapable of being deformed by the collision. 2.5.3. Arresting gear shall be incorporated in the pendulum to prevent ...
AutoNDA by SimpleDocs

Related to INSTALLATIONS, PROCEDURES AND MEASURES INSTRUMENTS

  • Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract. a. The contractor shall notify all potential subcontractors and suppliers and lessors of their EEO obligations under this contract. b. The contractor will use good faith efforts to ensure subcontractor compliance with their EEO obligations.

  • Solicitations for Subcontracts, Including Procurement of Materials and Equipment In all solicitations either by competitive bidding or negotiation made by the Local Government for work to be performed under a subcontract, including procurement of materials or leases of equipment, each potential subcontractor or supplier will be notified by the Local Government of the Local Government’s obligations under this Agreement and the Acts and Regulations relative to Nondiscrimination on the grounds of race, color, or national origin.

  • Solicitations for Subcontracts, Including Procurements of Materials and Equipment In all solicitations either by competitive bidding or negotiation made by the Engineer for work to be performed under a subcontract, including procurements of materials or leases of equipment, each potential subcontractor or supplier shall be notified by the Engineer of the Engineer's obligations under this contract and the Regulations relative to nondiscrimination on the grounds of race, color, or national origin.

  • Change Orders and Contract Amendments 33.1 The Procuring Entity may at any time order the Supplier through notice in accordance GCC Clause 8, to make changes within the general scope of the Contract in any one or more of the following: a) drawings, designs, or specifications, where Goods to be furnished under the Contract are to be specifically manufactured for the Procuring Entity; b) the method of shipment or packing; c) the place of delivery; and d) the Related Services to be provided by the Supplier. 33.2 If any such change causes an increase or decrease in the cost of, or the time required for, the Supplier's performance of any provisions under the Contract, an equitable adjustment shall be made in the Contract Price or in the Delivery/Completion Schedule, or both, and the Contract shall accordingly be amended. Any claims by the Supplier for adjustment under this Clause must be asserted within twenty-eight (28) days from the date of the Supplier's receipt of the Procuring Entity's change order. 33.3 Prices to be charged by the Supplier for any Related Services that might be needed but which were not included in the Contract shall be agreed upon in advance by the parties and shall not exceed the prevailing rates charged to other parties by the Supplier for similar services.

  • Interconnection Facilities Engineering Procurement and Construction Interconnection Facilities, Network Upgrades, and Distribution Upgrades shall be studied, designed, and constructed pursuant to Good Utility Practice. Such studies, design and construction shall be based on the assumed accuracy and completeness of all technical information received by the Participating TO and the CAISO from the Interconnection Customer associated with interconnecting the Large Generating Facility.

  • NEGOTIATIONS PROCEDURES A. The parties agreed to implement a Collaborative Bargaining Process beginning with the 1998- 99 fiscal year within the authority of Chapter 447 of the Florida Statutes and any appropriate rules and procedures. Salary and fringe benefits shall be automatically reopened each year, as well as any provisions imposed by the Board. In compliance with requirements that tentative agreement items must be formally ratified, the parties agree to establish the following protocol: 1. Formal ratification votes on tentative agreement(s) by the parties shall be held as needed. 2. Interim decisions to implement agreements before formal ratification shall be confirmed in writing in the form of a Memorandum of Understanding. 3. Issues may be raised for consideration through an appropriate process at any time during the length of this ratified agreement. B. If negotiations reach impasse, the procedures as set forth in the Florida Statutes and/or the rules of the Public Employees Relations Commission shall be followed. At the request of either party, a mediator shall be appointed. C. Neither party shall have any control over the selection of the bargaining representatives of the other party, and the parties mutually pledge that their representatives will be empowered to reach tentative agreement on items being negotiated. Should either party utilize the services of outside consultants to assist in negotiations, the party using the consultants shall pay for any cost incurred for such services. D. This Contract may not be modified in whole or in part except by mutual written agreement. E. If any provision or application of this Contract is held to be contrary to law, then such provision or application shall not be deemed valid and subsisting except to the extent permitted by law, but all other provisions or applications shall continue in full force and effect. The parties shall either immediately meet to reopen negotiations on that provision or application or mutually agree to deal with the matter in subsequent negotiations. F. The agreements in this Contract shall supersede any rules, regulations, or practices of the Board which are contrary to or inconsistent with the terms recorded herein. G. There shall be two official signed copies of the final ratified Contract, one to be retained by each of the parties. The Board agrees to print one thousand five hundred (1,500) copies of the current Contract for distribution to new hires. A link will be provided to all employees during pre-planning each school year. The Association will be provided 500 copies of the full contract each year. H. If bargaining is mutually scheduled during the teacher duty day, up to eleven members of the Association’s bargaining team shall be granted release time for travel, caucusing, and attendance at bargaining sessions. The parties shall mutually agree on parameters to release from duty Association team members following bargaining sessions which extend late. I. Tentative agreements shall be reduced to writing and submitted for ratification, within an agreed upon time, to the employees and to the Board. Failure to ratify tentative agreements shall make such tentative agreements null and void. 1. The parties may agree to submit packages of tentative agreements for ratification to the employees and the Board at any time. 2. If impasse is declared, the parties shall meet to review any pending tentative agreements unrelated to the impasse and to consider their submission for ratification as outlined in Section 1. above, prior to a special master hearing and prior to a public hearing. J. During the term of this Contract the Association and the Board recognize that events may arise which require a mutual interpretation or modification of this Contract that does not constitute a substantive change in employees’ salaries or benefits. Under these circumstances, the parties are authorized to enter into a settlement agreement or memorandum of understanding expressing these interpretations or modifications. If such are entered into during the term of this Contract, they will remain in effect until expiration of the Contract, until superseded by the Contract, or until mutually withdrawn by the parties. K. Operating Procedures and Guidelines: 1. The Collaborative Bargaining Leadership Team (CBLT) shall be composed of equal numbers of CTA members and District personnel. 2. The CBLT mutually agrees to coordinate and participate in appropriate training opportunities designed to support the process and/or build skills essential to the success of the process. The CBLT may utilize the services of consultants to assist in the negotiations. Any cost incurred shall be shared equally by the parties. 3. Define consensus as a status in which all members can support the decision and use consensus as the preferred decision making strategy in all decisions. 4. Operate as an open forum to identify, explore and resolve issues of importance to CTA and the District using District personnel as resources. The CBLT will solicit and value input from personnel affected by the outcome of the process. 5. All monies, except for School Recognition Dollars allocated by the Legislature as “bonus” and/or “incentive money” for teachers, shall be subject to discussion by the Collaborative Bargaining Leadership Team before distribution. 6. The CBLT will establish committees and will receive, review and make final decisions on recommendations from appropriate committees. All decisions are to be supported by data from those committees. All committee meetings will be accurately recorded. 7. Communicate with employees through a variety of mediums. 8. There will be a notice to the CBLT participants before either party communicates any specific issues generated or discussed during the CBLT process unless it is mutually agreed to amend this timeline. L. Provisions to submit issues to the CBLT 1. Employees shall submit issues to the CBLT using the Issues for Submission form found on the CBLT websites: xxxxx://xxx.xxxx.xxx/es/legislative/laborrelations/Pages/default.aspx and xxx.xxxxxxxxx.xxx. 2. Forms may be found at individual work locations or the Association office. 3. The CBLT shall determine the appropriate action to be taken and notify the submitting party of such action. M. Committees of the CBLT 1. Committees shall be composed of equal numbers of CTA members and District personnel. 2. Committees will receive and undertake activities to execute the specific charge from the CBLT. Each party shall select a member that will act as a co-chair for each committee. 3. Committees shall welcome employees who might be affected by the issue to attend and provide information as a resource. Committees may invite outside resources as necessary. 4. Committees shall identify options supported by data to be recommended to the CBLT. 5. Committees shall keep accurate records of all committee meetings. 6. Committees and Task Forces a. Standing Committees The Collaborative Bargaining Leadership Team has established standing committees to field issues and concerns from their stakeholders. The committees meet on a regular basis to discuss issues and to collect data to support their recommendations. Each committee presents periodic reports and recommendations to the Collaborative Bargaining Leadership Team. The committees are as follows: 1.) Finance and Compensation 2.) Assessment

  • Violence Policies and Procedures The Employer agrees to have in place explicit policies and procedures to deal with violence. The policy will address the prevention of violence, the management of violent situations, provision of legal counsel and support to employees who have faced violence. The policies and procedures shall be part of the employee's health and safety policy and written copies shall be provided to each employee. Prior to implementing any changes to these policies, the employer agrees to consult with the Association.

  • Procedures for Providing NP Through Full NXX Code Migration Where a Party has activated an entire NXX for a single Customer, or activated at least eighty percent (80%) of an NXX for a single Customer, with the remaining numbers in that NXX either reserved for future use by that Customer or otherwise unused, if such Customer chooses to receive Telephone Exchange Service from the other Party, the first Party shall cooperate with the second Party to have the entire NXX reassigned in the LERG (and associated industry databases, routing tables, etc.) to an End Office operated by the second Party. Such transfer will be accomplished with appropriate coordination between the Parties and subject to appropriate industry lead times for movements of NXXs from one switch to another. Neither Party shall charge the other in connection with this coordinated transfer.

  • Placement of DNS probes Probes for measuring DNS parameters shall be placed as near as possible to the DNS resolvers on the networks with the most users across the different geographic regions; care shall be taken not to deploy probes behind high propagation-­‐delay links, such as satellite links.

  • Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!