Manufacturing Platform Sample Clauses

Manufacturing Platform. The Members acknowledge and agree that the Board may, in its discretion, elect to design, build and operate a manufacturing platform (the “Manufacturing Platform”) that will provide services that support the manufacturing activities of Producing Members, subject to the provisions of this Section 7.8. (a) Any and all governance decisions regarding the Manufacturing Platform (including the decision to establish the Manufacturing Platform and decisions regarding the design, build and operation of the Manufacturing Platform) will be made solely by the Producing Member Directors, in a manner consistent with the governance provisions of this Article VII (except that, for this purpose, the Producing Member Directors will be deemed to be the only members of the Board of Directors). (b) All costs and expenses incurred by the Company in connection with the design, build and operation of the Manufacturing Platform will be borne solely by the Producing Members. The basis on which the Producing Members will share costs and expenses associated with the Manufacturing Platform (including design, build and operating costs) will be determined by the Producing Member Directors, consistent with Section 7.8(a). [***]. If a Member that is not a Producing Member as of the date of this Agreement subsequently becomes a Producing Member, that Member will be deemed to be a Producing Member for all purposes hereof and will be entitled to participate in the Manufacturing Platform on the same economic and governance terms as an original Producing Member, including by bearing its respective pro rata share of the design, build and operating costs referred to in this Section 7.8(b) based upon its relative production volumes. [***]. The Company will ensure that (i) costs related to the Distribution Platform and the Manufacturing Platform, respectively, are properly allocated and that such costs are accurately reflected in the fees charged to Members pursuant to the applicable Master Services Agreements, and (ii) [***]. (c) If the Producing Member Directors elect to establish the Manufacturing Platform as contemplated under this Section 7.8, any provisions of this Agreement inconsistent with the provisions of this Section 7.8 will be adjusted as necessary to make them consistent with the provisions of this Section 7.8 (e.g., Capital Contributions required to be made in connection with the Manufacturing Platform will be made solely by the Producing Members, on the basis determined by the Pro...
Sample 1
AutoNDA by SimpleDocs

Related to Manufacturing Platform

  • Manufacturing (a) The Supplier shall without limitation be responsible, at no additional cost to the Purchaser, for: sourcing and procuring all raw materials for the Products; obtaining all necessary approvals, permits and licenses for the manufacturing of the Products; providing sufficient qualified staff and workers to perform the obligations under this Purchase Agreement; implementing and maintaining effective inventory and production control procedures with respect to the Products; and handling other matters as reasonably requested by the Purchaser from time to time. (b) The Supplier shall not change any process, material, component, packaging or manufacturing location without the Purchaser’s express prior written approval.

  • Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].

  • API If the Software offers integration capabilities via an API, your use of the API may be subject to additional costs or Sage specific policies and terms and conditions (which shall prevail in relation to your use of the API). You may not access or use the API in any way that could cause damage to us or the Software, or in contravention of any applicable laws. We reserve the right in our sole discretion, to: (i) update any API from time to time; (ii) place limitations around your use of any API; and (iii) deny you access to any API in the event of misuse by you or to otherwise protect our legitimate interests.

  • Commercialization Reports Throughout the term of this Agreement and during the Sell-Off Period, and within thirty (30) days of December 31st of each year, Company will deliver to University written reports of Company’s and Sublicensees’ efforts and plans to develop and commercialize the innovations covered by the Licensed Rights and to make and sell Licensed Products. Company will have no obligation to prepare commercialization reports in years where (a) Company delivers to University a written Sales Report with active sales, and (b) Company has fulfilled all Performance Milestones. In relation to each of the Performance Milestones each commercialization report will include sufficient information to demonstrate achievement of those Performance Milestones and will set out timeframes and plans for achieving those Performance Milestones which have not yet been met.

  • Promotional Materials In the event that the Fund or the Adviser makes available any promotional materials related to the Securities or the transactions contemplated hereby intended for use only by registered broker-dealers and registered representatives thereof by means of an Internet web site or similar electronic means, the Adviser will install and maintain, or will cause to be installed and maintained, pre-qualification and password-protection or similar procedures which are reasonably designed to effectively prohibit access to such promotional materials by persons other than registered broker-dealers and registered representatives thereof.

  • Software Products Save as otherwise set forth in the Agreement, the right to use any Software Product is personal to the Licensee, for its own internal use, and is non-transferable, except with the Licensor’s prior written consent, in which case the Licensee shall cause the assignee or sub-licensee to agree to the terms of this Software License.

  • Marketing Materials (a) During the term of this Agreement, the Sub-Adviser agrees to furnish the Manager at its principal office for prior review and approval by the Manager all written and/or printed materials, including but not limited to, PowerPointÒ or slide presentations, news releases, advertisements, brochures, fact sheets and other promotional, informational or marketing materials (the “Marketing Materials”) for internal use or public dissemination, that are produced or are for use or reference by the Sub-Adviser, its affiliates or other designees, broker-dealers or the public in connection with the Series, and Sub-Adviser shall not use any such materials if the Manager reasonably objects in writing within five business days (or such other period as may be mutually agreed) after receipt thereof. Marketing Materials may be furnished to the Manager by first class or overnight mail, facsimile transmission equipment, electronic delivery or hand delivery. (b) During the term of this Agreement, the Manager agrees to furnish the Sub-Adviser at its principal office all prospectuses, proxy statements, reports to shareholders, or Marketing Materials prepared for distribution to shareholders of each Series, or the public that refer to the Sub-Adviser in any way, prior to the use thereof, and the Manager shall not use any such materials if the Sub-Adviser reasonably objects in writing within five business days (or such other period as may be mutually agreed) after receipt thereof. The Sub-Adviser’s right to object to such materials is limited to the portions of such materials that expressly relate to the Sub-Adviser, its services and its clients. The Manager agrees to use its reasonable best efforts to ensure that materials prepared by its employees or agents or its affiliates that refer to the Sub-Adviser or its clients in any way are consistent with those materials previously approved by the Sub-Adviser as referenced in the first sentence of this paragraph. Marketing Materials may be furnished to the Sub-Adviser by first class or overnight mail, facsimile transmission equipment, electronic delivery or hand delivery.

  • Customer Materials Subject to Section 4(a), all right, title and interest (including all Intellectual Property Rights) in and to the Customer Materials are owned by Customer or Customer’s suppliers.

  • Manufacture 2.1. The LED(s) on the LED module shall be equipped with suitable fixation elements. 2.2. The fixation elements shall be strong and firmly secured to the LED(s) and the LED module.

  • Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!