Names and addresses of Technical Services responsible for conducting approval tests and of Type Approval Authorities. The Contracting Parties to the 1958 Agreement applying this Regulation shall communicate to the United Nations Secretariat the names and addresses of the Technical Services responsible for conducting approval tests and of the Type Approval Authorities which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, or production definitively discontinued, issued in other countries, are to be sent.
Names and addresses of Technical Services responsible for conducting approval tests and of Type Approval Authorities. The Parties to the 1958 Agreement applying this Regulation shall communicate to the United Nations Secretariat the names and addresses of the Technical Services responsible for conducting approval tests and of the Type Approval Authorities which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, or production definitively discontinued, issued in other countries, are to be sent. (Maximum format: A4 (210 x 297 mm) concerning:2 Approval granted Approval extended Approval refused Approval withdrawn Production definitively discontinued of restraining devices for child occupants of power-driven vehicles, pursuant to Regulation No. 129. Approval No.: ...................……………… Extension No.: ...........................................
1.1. Forward-facing child restraint/rearward-facing child restraint/lateral-facing child restraint
1.2. Integral/partial/booster cushion;2
1.3. Belt type: 2 (Adult) three-point belt (Adult) lap belt Special type belt/retractor 2
1.4. Other features: chair assembly/impact shield2 ..................................................
Names and addresses of Technical Services responsible for conducting approval tests and of Type Approval Authorities. The Contracting Parties to the 1958 Agreement which apply this Regulation shall communicate to the United Nations Secretariat the names and addresses of the Technical Services responsible for conducting approval tests and of the Type Approval Authorities which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, issued in other countries, are to be sent.
1. Verifying CoP on the criteria emissions for pure ICE vehicles, NOVC-HEVs and OVC-HEVs
1.1. Each vehicle shall be tested on the chassis dynamometer set with the specific mass inertia setting and road load parameters of the individual vehicle. The chassis dynamometer shall be set to the target road load for the test vehicle according to the procedure specified in paragraph 7. of Annex B4.
1.2. The applicable test cycle is the same used for the type approval of the interpolation family to which the vehicle belongs.
1.3. The preconditioning test shall be carried out according to the provisions of paragraph 2.6. of Annex B6, or of Appendix 4 to Annex B8, as applicable.
1.4. The test results shall be the values calculated for pure ICE vehicles according to Step 9 of Table A7/1 of Annex B7, for NOVC-HEVs and OVC-HEVs according to Step 8 of Table A8/5 of Annex B8 for the charge-sustaining criteria emissions and according to Step 6 of Table A8/8 of Annex B8 for the charge-depleting criteria emissions. Conformity against the applicable criteria emission limits shall be checked using the pass/fail criteria specified in paragraph 6.3.10. of this Regulation.
2. Verification of CoP on CO2 mass emissions/ fuel efficiency of pure ICE vehicles
2.1. The vehicle shall be tested according to the Type 1 test procedure described in Annex B6.
2.2. During this test, the CO2 mass emission after 4 phases MCO2,c,6 shall be determined according to step 6 of Table A7/1 of Annex B7. During this test, the fuel efficiency after 3 phases FEc,5 shall be determined according to step 5 of Table A7/1 of Annex B7.
2.3. The conformity of production with regard to CO2 mass emissions shall be verified on the basis of the values for the tested vehicle as described in paragraph 2.3.1. and applying a run-in factor as defined in paragraph 8.2.4. of this Regulation. The conformity of production with regard to fuel efficiency shall be verified on the basis of the values for the tested vehicle as described in paragraph 1.3.1. and applying a run-in factor as defined in paragraph 8.2.4. of this Regula...
Names and addresses of Technical Services responsible for conducting approval tests and of Type Approval Authorities. The Contracting Parties to the Agreement applying this Regulation shall communicate to the United Nations Secretariat the names and addresses of the technical services responsible for conducting approval tests and of the Type Approval Authorities which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval or production definitively discontinued, issued in other countries, are to be sent. (Maximum format: A4 (210 x 297) issued by: Name of Administration: ...................................... ...................................... ...................................... Concerning:5 Approval granted Approval extended Approval refused Approval withdrawn Production definitively discontinued of a type of agricultural or forestry vehicle with regard to the installation of lighting and light-signalling devices pursuant to Regulation No. 86.
Names and addresses of Technical Services responsible for conducting approval tests and of Type Approval Authorities. The Contracting Parties to the Agreement which apply this Regulation shall communicate to the United Nations Secretariat the names and addresses of the Technical Services responsible for conducting approval tests and of the Type Approval Authorities which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, issued in other countries, are to be sent. For Public Comment Only The Technical Services responsible for conducting approval tests shall comply with the harmonized standards concerning the operation of testing laboratories (ISO/CEI Guide 25). In addition they should be designated by the Type Approval Authority for which they carry out the approval tests. (Maximum format: A4 (210 x 297 mm)) Concerning:2 Approval granted Approval extended Approval refused Approval withdrawn Production definitively discontinued of a type of safety glazing material pursuant to Regulation No. 43.
