Sinks Sample Clauses

Sinks a. Sinks shall be of stainless steel. b. Each sink shall be provided with R.S. or C.I. brackets and clips and securely fixed. c. Counter top sinks shall be fixed with suitable angle iron clips or brackets as recommended by the manufacturer. Each sink shall be provided with 40mm diameter C.P. waste with chain and plug or P.V.C. waste. Fixing shall be done as directed by the Independent Engineer. d. Fittings for supply to sinks shall be C.P. brass single hole mixing fitting with swinging spout for hot and cold water and C.P. brass swan neck tap swinging spout for cold water supply.

Sinks. Sinks are to be cleaned and polished removing all residues from drain areas.

Sinks. All stalls handling, preparing or cooking food are to be provided with a sink for food preparation and a double bowl sink or trough for conducting cleaning and sanitising of food preparation utensils and equipment. The double bowl sink or trough must be large enough to wash the largest food utensil, pot or pan.

Sinks. Never put anything down the sinks in either the bathroom or the kitchen other than fluids. All solids must be disposed of in the garbage cans. This means NO FOOD CAN BE DISPOSED IN THE KITCHEN OR BATHROOM SINKS! If someone has to come and unclog your sink due to not following the above statement, there is a $75 charge.

Sinks. This warranty covers sink installation for one-year, which includes, caulking and adhesion to the stone.

Sinks. There must be a three-bay sink on the unit for utensil washing. A separate sink for hand washing is also required. Soap and single use towels (paper towels) must be supplied to the hand washing sink.

Sinks. Laboratory sink shall confirm to IS-2256 with the waste hole of minimum dia 65 mm at the bottom of sink. The floor of sink shall gently slope towards the outlet. The sink shall have wear type over flow below 30 mm of top edge. Each sink shall be provided with a brass, chromium plated 50 mm dia waste fitting. The sinks shall have xxxx type over flow and their invert shall be 30 mm below the top edge.

Sinks. 18.2.10.1 Laboratory Sinks shall conform to IS 2556 (Part 5)-1994: Specification for vitreous sanitary appliances(vitreous china), part 5, specific requirements for Laboratory Sinks. The floor of sink shall gently slope towardsthe outlet. The waste hole shall have a minimum dia of 65 mm at the bottom to suit the waste fitting. Eachsink shall be provided with a brass, chromium plated 50 mm dia waste fitting. The sinks shall have xxxx typeover flow and their invert shall be 30 mm below the top edge. 18.2.10.2 The basin or sink shall be supported on a pair of cast iron brackets set in cement mortar 1:3 for lighterappliances or embedded in cement concrete 1:2:4 type B1, blocks 100 x 75 x 150 mm in size. The wall plasteron the rear shall be cut to rest over the top edge of the basin where directed. After fixing the basin, the plastershall be made good and surface finished as directed. 18.2.10.3 The chromium plated trap and union shall be connected to 32 mm dia waste pipe in case of washbasins and 50 mm waste pipe in case of sinks, which shall be suitably bent towards the wall. Waste pipe shalldischarge directly on to a floor or Nahani trap or gully trap or into an open channel leading to floor trap, orshall be connected to a waste pipe stack through a floor trap. CP brass union shall not be provided when asurface channel, drain or floor trap is placed directly under the wash basin and the waste discharges into itvertically. The height of front edge of wash basin or sink from the floor level shall be 80 cm unless otherwiseindicated.

Sinks. Gas lines, valves and regulators.

Sinks. Clean all sinks with a cloth and appropriate cleaner. Make sure all sides and undersides of sinks are cleaned. Clean and dry all chrome fixtures. Remove graffiti.