Splinting Sample Clauses

Splinting. Crowns, fillings or appliances that are used to connect (splint) teeth, or change or alter the way the teeth meet, including altering the vertical dimension, restoring the bite (occlusion) or are cosmetic.
AutoNDA by SimpleDocs
Splinting. The joining of teeth to support each other for periodontal reasons (stabilization) by crowns or other means. Splinting for stabilization due to an accident or injury is a covered benefit. Sterilization Sterilization preparation, infection control, operatory preparation and sepsis control are considered part of all procedures and are not a benefit. Temporary or interim procedures You are not covered for temporary or interim procedures. Temporomandibular joint (TMJ) dysfunction You are not covered for expenses incurred for diagnostic x-rays, appliances, restorations or surgery in connection with temporomandibular joint dysfunction or myofunctional therapy, unless temporomandibular joint (TMJ) dysfunction services are covered on the summary of benefits sheet.
Splinting. (6) Retentive Pins in Abutments: Major Restorative:

Related to Splinting

  • Fingerprinting For purposes of this Agreement and because the District will provide a qualified employee for the supervision of District's students at all times that Consultant is present and performing services at an active school site, Consultant shall be relieved of the requirements to provide a criminal background check pursuant to California Education Code 45125.1.

  • Printing If this Agreement involves the duplication of more than 5,000 copies of a single page or more than 25,000 copies of multiple pages, this Agreement incorporates by reference DEAR 970.5208-1 Printing (Dec 2000).

  • Grading The coarse aggregate as delivered to the mixer, shall be well graded as per IS specifications. Maximum size of aggregate used for the work shall be 20mm or 40mm or as specified in items in the bill of quantities and it shall confirm to IS: 383-1970, clause 4.2 (Table-2) However, the exact gradation required to produce a dense concrete of specified strength and desired workability shall be decided as per laboratory test by the Engineer. Coarse aggregate for use in concrete shall be well graded and shall conform to IS: 383-1970 requirements (as per Table-II) given below: IS sieve Designation Percentage Passing by weight for graded aggregate of nominal size. 40mm 20mm 16mm 12.5mm 63mm 100 - - - 40mm 00-000 000 - - 20mm 00-00 00-000 100 - 16mm - - 00-000 000 12.5 - - - 90-100 10.00 00-00 00-00 00-00 00-00 4.75mm 0-5 0-10 0-10 0-10

  • Painting All exterior surfaces and materials requiring paint shall be prime coated plus 2 coats of Xxxxxxx Xxxxxxxx Pro-Mar alkyd flat exterior finish, or Xxxxxxx-Xxxxxxxx SWP exterior gloss paint. All porous exterior surfaces (e.g. unpainted wood) shall be sealed with 2 coats of Xxxxxxxx’x Water Seal following the manufacturers application instructions. Interior surfaces requiring paint shall be prime coated plus 2 coats of Xxxxxxx Xxxxxxxx Pro-Mar Latex Eg-Shel enamel. Concrete block walls shall receive 1 coat of Xxxxxxx Xxxxxxxx Pro-Mar Block Filler and 2 coats of Xxxxxxx Xxxxxxxx Pro-Mar latex Eg-Shel enamel. Interior finishes and color selections shall be approved by the State. A schedule of colors and finishes shall be prepared by the Owner/Lessor and approved by the State.

  • New Member Orientation The Employer will notify the Union of any newly represented temporary employees. The Union will be given the opportunity to have a Union representative speak with the newly represented temporary employees for not more than thirty (30) minutes to provide information about the Union and this Agreement.

  • Coaching Informal discussion or instruction between employee and their immediate supervisor. Supervisor may follow up in writing which may include a simple action plan. This is not a form of corrective action.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!