CLASSIFICATIONS AND WAGES 1.1 a) Engineers operating: cranes with a manufacturer’s rating of over 164 to 219 tons capacity. Effective May 1, 2013, the wage rate for engineers operating large cranes 220 to 299 tons capacity shall be One Dollar and Twenty-Five Cents ($1.25) per hour above the applicable rate. The wage rate for engineers operating large cranes 300 to 499 tons capacity shall be Two Dollars and Fifty Cents ($2.50) per hour above the applicable rate. The wage rate for engineers operating large cranes over 499 tons capacity shall be Four Dollars ($4.00) per hour above the applicable rate. EFFECTIVE DATE WAGES VACATION PAY BENEFIT PLAN PENSION PLAN TOTAL May 27, 2016 $42.71 $4.27 $5.29 $6.73 $59.00 May 1, 2017 $43.66 $4.37 $5.34 $6.88 $60.25 May 1, 2018 $44.62 $4.46 $5.39 $7.03 $61.50
Types of Grievance (a) An individual grievance is a grievance which involves a single individual.
Sector Sub-Sector Industry Classification Level of Government Type of Obligation Description of Measure Source of Measure All sectors : : - : Central : National Treatment Senior Management and Board of Directors : National Treatment and the Senior Management and Board of Directors obligations shall not apply to any measure relating to small and medium sized domestic market enterprise2. Foreign equity is restricted to a maximum of 40% for domestic market enterprises with paid-in equity capital of less than the equivalent of USD 200,000 Note: Members of the Board of Directors or governing body of corporation or associations shall be allowed in proportion to their allowable participation or share in the capital of such enterprises. : -1987 Constitution of the Republic of the Philippines. - Foreign Investments Act of 1991 (R.A. No. 7042, as amended by R.A. No. 8179). -Presidential and Administrative Issuances. ∞ 2 The concept of a small and medium sized domestic market enterprise is an enterprise with paid in equity capital of less than the equivalent of USD 200,000.00.
DOMESTIC PREFERENCES FOR PROCUREMENTS To the extent applicable, Supplier certifies that during the term of this Contract will comply with applicable requirements of 2 C.F.R. § 200.322.
Drop Shipped Off loaded by carrier to an Agency loading dock or designated area. There will be no charge to the ordering Agency for this delivery method.
Organisation SFA has over two hundred full time staff reporting to the Chief Executive. He is supported directly by an executive team, each member of which has POLICY DETERMINED BY SENIOR senior management responsibility for a specific aspect of SFA's activity. PRACTICIONERS AND INDEPENDENTS SUPPORTED BY A PROFESSIOINAL Overseeing the work of the executive is the Chairman and Board of EXECUTIVE AND STAFF Directors. These are not employees of SFA but are either senior practitioners from member firms or persons independent of SFA and its firms who represent the interests of the investor. The Board delegates responsibility for the detail of policy, rulemaking and disciplinary procedures to specialist committees which are also composed of practitioners and independents. Supported by a professional staff, this combination provides for effective and flexible self-regulation. REGULAR CONTACT WITH GOVERNMENT BODIES, Public Relations 'CITY' INSTITUTIONS, PROFESSIONAL BODIES AND SFA's communication with the public, Parliament, `City' institutions, THE PRESS professional bodies and other regulators, at home and abroad, plays an important part in the process of developing confidence in SFA members' businesses and in furthering the success of the regulatory system as a whole. Accordingly SFA maintains regular contact with the press and other media. Press coverage of disciplinary action taken by SFA acts as a reassurance to the public and to the financial community that SFA is actively seeking to help promote good practice in London's markets. Further information More details are available on the various aspects of SFA's work and what it does to put the investor first. Other publications include: o Rule Book and amendment service* o Professional Dealing Handbook* o Board Notices* o Membership Directory* o Briefing, SFA's Membership newsletter o Annual Report and Accounts (with Regulatory Plan) o Complaints Bureau o Annual Report of the Complaints Commissioner o Annual Report of the Chairman of the Arbitration Panel o Consumer Arbitration Scheme o Full Arbitration Scheme Rules o Membership Application Pack** o Available by subscription ** For applicant firms (after a preliminary discussion) SFA The Securities and Futures Authority Limited Cottons Centre Cottons Lane London SE1 2QB Tel: 000 000 0000 Xxx: 000 000 0000 Xxxxxxxxed in England xxx Xxxxx Xx 1998622 Xxxxxxxxxx Office as above Fifth edition July 1994
Technical and Organisational Measures (1) Before the commencement of processing, the Supplier shall document the execution of the necessary Technical and Organisational Measures, set out in advance of the awarding of the Order or Contract, specifically with regard to the detailed execution of the contract, and shall present these documented measures to the Client for inspection. Upon acceptance by the Client, the documented measures become the foundation of the contract. Insofar as the inspection/audit by the Client shows the need for amendments, such amendments shall be implemented by mutual agreement.
Immunisation 7.4.1 The parties agree in principle that responsibility for pre-exposure immunisation of employees rests with employers who should accept responsibility for safety in the workplace, advised as necessary by health officials.
CFR PART 200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, class, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, glass, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
