Cooling capacity definition

Cooling capacity means a measure of the ability of an air conditioner to remove heat from an enclosed space, as determined using the applicable test method in Section 1604(b) or 1604(c).
Sample 1Sample 2Sample 3
Cooling capacity means the nominal tonnage of compression equipment based on 40 degrees Fahrenheit suction temperature and 105 degrees Fahrenheit condensing temperature.
Sample 1Sample 2Sample 3
Cooling capacity means the amount of cooling, in Btu/h, provided to an indoor conditioned space, determined in Section 4.1 of appendix F.
Sample 1Sample 2Sample 3

Examples of Cooling capacity in a sentence

  • Cooling capacity will fall when the air circulation inside is hindered.• Do not place the refrigerator in places subject to direct sunlight.

  • Cooling capacity of each unit shall be able to remove all the sensible heat from the MCR.

  • Key Assumptions: • BtuH = Cooling capacity in Btu/Hour – This value comes from ARI or AHAM rating or manufacturer data.

  • Cooling capacity will fall when the air circulation inside is hindered.• Do not place the Freezer in places subject to directsunlight.

  • The theoretical volume of the water loop for a proper air conditioning operation can be calculated using the formula hereafter:Q  Cooling capacity of the chiller in kWN  Number of capacity stage of the chiller Dt  Water temperature Delta T.

  • The 1.11 factor used for both energy and capacity is a weighted average loss factor and was adopted by consensus.Example: Central Air ConditionerEnergy Impact (kWh) = CAPY/1000 × (1/SEERb – (1/SEERq × (1-ESF)) × EFLHCAPY = Cooling capacity (output) of systemSEERb = The Seasonal Energy Efficiency Ratio of the Baseline Unit (set at 10).SEERq = The Seasonal Energy Efficiency Ratio of the qualifying unit installed.

  • The theoretical volume of the water loop for a proper air conditioning operation can be calculated using the formula hereafter:Q 🡪 Cooling capacity of the chiller in kW N 🡪 Number of CompressorX 🡪 Number depending of the type of compressor (Scroll 12, screw 8, Recip 10) Vt = 172 x Q/(n x X) litres Example, for a screw chiller with 2 compressors 400kW, water conditions, the minimum volume is : Vt = 172 x 400/(2 x 8) = 4300 l.

  • Cooling capacity of the aftercooler must be sized for the total capacity of the compressors.

  • Cooling capacity of the aftercooler shall be sized for the total capacity of the compressors.

  • Pf : Cooling capacity valid for a ∆T according to operating limits.


More Definitions of Cooling capacity

Cooling capacity. ’ means the amount
Sample 1Sample 2
Cooling capacity. ’ means the amount of cooling, in British thermal units per hour (Btu/h), provided to a conditioned space, measured under the specified conditions and determined in section 4.1 of this appendix.
Sample 1Sample 2
Cooling capacity. ( 製 冷 量 ) means the amount of sensible and latent heat that an air-conditioner can remove from the enclosed space, room or zone to which free delivery of conditioned air is provided in a defined period of time;
Sample 1
Cooling capacity. (製冷量) means the amount of sensible and latent heat
Sample 1
Cooling capacity means the heat load [W] that can be eliminated from the indoor air per unit hour, when the multi air conditioner is operated for cooling.
Sample 1

Related to Cooling capacity

  • Reserved Capacity means the maximum amount of capacity and energy that the Transmission Provider agrees to transmit for the Transmission Customer over the Transmission Provider’s Transmission System between the Point(s) of Receipt and the Point(s) of Delivery under Tariff, Part II. Reserved Capacity shall be expressed in terms of whole megawatts on a sixty (60) minute interval (commencing on the clock hour) basis.

  • Nameplate Capacity means the maximum electrical generating output (in MWe) that a generator can sustain over a specified period of time when not restricted by seasonal or other deratings as measured in accordance with the United States Department of Energy standards.

  • Bid Capacity meanss capacity offered by the bidder in his Bid under invitation.

  • Project Capacity means the AC capacity of the project at the generating terminal(s) and to be contracted with MSEDCL for supply from the Solar Power Project.

  • Unforced Capacity shall have the meaning specified in the Reliability Assurance Agreement.

  • Ramping Capability means the sustained rate of change of generator output, in megawatts per minute.

  • Contracted Capacity means the capacity (in MW AC) contracted with MSEDCL for supply by the successful bidder at the Delivery Point from the Solar Power Project.

  • Installed Capacity or 'IC’ means the summation of the name plate capacities of all the units of the generating station or the capacity of the generating station (reckoned at the generator terminals), approved by the Commission from time to time;

  • Interruptible Capacity means capacity that may be interrupted by the Operator at any time in order to fulfil shippers’ nominations under a firm capacity reservation.

  • Net Qualifying Capacity has the meaning set forth in the CAISO Tariff.