Requirements. 1. Individuals meeting the following requirements may apply for the position of Senior Teaching Assistant:
Requirements. 1. Individuals meeting the following requirements may apply for the position of Senior Teaching Assistant: Specialistica/Magistrale) awarded in accordance with the regulations set out in Ministerial Decree 509/99 and Ministerial Decree 270/04;
Requirements. 4.1 General Watermist systems shall only be designed, installed and maintained by qualified companies and shall comply with the following requirements. The safe use of a water mist system is limited to applications it has been tested for. Parameters used during such tests define the limits of its application, unless methods being acceptable to the authorities having jurisdiction to interpolate test results can be applied. Parameters include room geometry, ventilation conditions, fire load, etc. Watermist systems shall be tested in accordance with Annex A. For scenarios where Annex A is not applicable, it is recommended to test watermist systems in accordance with Annex B by a recognized third party laboratory. In this case, the results of the test protocol should be acceptable to the authority having jurisdiction, responsible for the acceptance of the system. Annex A describes fire test protocols for a variety of hazard groups. Watermist systems shall be successfully tested in accordance with these test protocols. Annex B provides guidelines for defining representative fire test protocols based on a proper fire protection engineering evaluation of the fire hazard, the compartment conditions, and the performance objectives for the system. The full system evaluation also includes component testing. Annex D describes the testing of watermist nozzles. For other components, a customized evaluation or review should be carried out based on existing component standards. If no suitable component standard is available, case-by-case evaluations should be conducted by qualified testing laboratories. Water mist systems shall be certified in conformity to all requirements of this document by a recognized authority. Where a watermist system or an extension or alteration to a watermist system is being considered within new or existing buildings, the relevant parties shall be consulted and, where necessary, their approval sought at an early stage, e.g. the water supply authority, the fire authority; the insurer(s) of the building and building contents.
Requirements. Candidates will be considered eligible for selection based on the following essential requirements, to be fulfilled by the deadline for applications:
Requirements. Degree: PhD (less than 5 years as PhD degree) • Degree field: Biological sciences, (Bio)Chemistry, Pharmaceutical • Required Languages: English (Fluent).
Requirements. Education: secondary education (IT or related/similar to IT) administration or logistics Professional experience: Language knowledge Language Level
Requirements. In un Secure-SDLC i requisiti di sicurezza devono essere sviluppati accanto ai requisiti funzionali. Questo principio, noto come “Security by Design and by Default” dispone che qualsiasi sistema informatico debba prevedere la valutazione del rischio fin dalle prime fasi della sua realizzazione.
Requirements. MBO (institute of technology) Shipbuilding or MBO education level in combination with relevant work experience. • AutoCAD, Rhino and of course, thorough knowledge of computers. • Written and spoken English. • Proven experience in outfitting engineering. • Hands on mentality. Contactperson: Xxxxx Xxxxx • Mobiel: 0000(0)000000000 • Tel: 0000(0)000000000 • Email: Assisting clients in their purchases, general upkeep of the shop and store, deliveries where necessary, pricing and shelving products and entering products in the P.O.S system.
Requirements. Researchers taking part in the cooperation programs hereunder shall contract a medical insurance entitling the holder to free emergency medical treatment in the host country. The receiving Party will provide the visitor with all indispensable organisational assistance in situations requiring such steps. Within a term of no more than 30 business days, as of the execution date hereof, a Coordination Committee shall be set up, consisting of an incumbent and an alternate member of each party. This Committee shall be in charge of planning, tracking and evaluating the acts resulting from this Memorandum of Understanding. Such Committee shall hold meetings, face to face or online, at least once a year, upon request of any of the parties, and its reports and proposals shall be submitted to the executive levels of both parties.
Requirements. The following requirements are applicable to the Front-End Board (FEB). Most numbers given are not final but good estimates. The final values will be provided by the customer at the Kick-off meeting of the contract • Dimensions approximately 70 x 65 mm2 (TBC), nominal thickness 1.5 mm (TBC). Specific shape and geometry required • The FEB lateral dimension tolerance shall be ± 0.1 mm • The FEB thickness tolerance shall be ± 0.15 mm • Baseline material shall be Al2O3 ceramic (96 %) with thick-film technology • Trace density (pitch) 100 µm • Thermal conductivity of substrate > 24 W/(m·K) o Coefficent of Thermal Expansion (CTE) of substrate ≤ 8 µm/(m ∙ K) in the whole operative temperature range • Temperature range o operational: from -55 °C to +30 °C TBC o non-operational: from -60 °C to +80 °C TBC • Glue selected in order to guarantee the connections over lifetime (five years) and over non- operational temperature range • Compliant with high voltages up to 2600 V for a limited area of the PCB • No potting or other encapsulation allowed for any naked die or wire bonding • The FEB and all its components shall be designed to withstand a total radiation dose of 100 krad The electrical layout of the FEB will be provided by the Customer as input in KiCAD EDA (TBC) format and, if needed, shall be fine-tuned by the Contractor in open collaboration with the Customer, according to design rules compliant with the thick-film technology. The possibility of re-work of ASICs is a must. Customer and Contractor will jointly evaluate the re-work procedure and will study the possibility to mount replacement ASICs on-top of faulty ASICs. Attività richieste • Attività generali o Progetto, acquisto dei materiali e realizzazione del substrato thick film per la Front-end board (FEB) o Progetto, acquisto dei materiali e realizzazione del Wrap around o Montaggio superficiale della FEBs e dei wrap around, incluso l’acquisto dei materiali o Die- e wirebonding degli ASIC o Acquisto dei cavi per HV e MV, collegamento dei connettori e saldature alla FEB o Progetto e realizzazione dei tool meccanici per assemblaggio e produzione o Progetto e realizzazione dei contenitori di trasporto delle FEB assemblate o Documentazione • Produzione delle Front-End Board