Automatic and Manual Fire Fighting Equipment Sample Clauses

Automatic and Manual Fire Fighting Equipment. This Facility operates with 33 ABC-type fire extinguishers. The wall mounting unit must adhere to all fire codes and include a breakable front cover. The required fire extinguishers shall be onsite and maintained at the commencement of this Contract. If any of the extinguishers are damaged, stolen, missing or inoperable during this Contract term, they are to be replaced and/or maintained at the Contractor’s expense within 30 Days. The Contractor shall test the fire suppression system and flush the system annually during the Term of the Contract. The service report must be submitted to the Department after each year’s test. The Contractor’s failure to replace and/or maintain any of the extinguishers and/or cabinets or failure to flush out and test the fire suppression system within the specified time frame shall result in the Contractor being subject to the assessment of liquidated damages of $100.00 per day. The Contractor shall provide inspection, testing and maintenance service to the fire alarm system and all of its associated components. Failure to do so will result in the Contractor being subject to the assessment of liquidated damages of $100.00 per day.
Sample 1
AutoNDA by SimpleDocs
Automatic and Manual Fire Fighting Equipment. This Facility operates with 30 ABC-type fire extinguishers. The wall mounting unit must adhere to all fire codes and include a breakable front cover. The required fire extinguishers shall be onsite and maintained at the commencement of this Contract. If any of the extinguishers are damaged, stolen, missing or inoperable during this Contract term, they are to be replaced and/or maintained at the Contractor’s expense within 30 Days. The Contractor shall test the fire suppression system and flush the system annually during the Term of the Contract. The service report must be submitted to NYCDOT after each year’s test. The Contractor’s failure to replace and/or maintain any of the extinguishers and/or cabinets or failure to flush out and test the fire suppression system within the specified time frame shall result in the Contractor being subject to the assessment of liquidated damages of $100.00 per day. (When applicable) The contractor shall provide inspection, testing and maintenance service to the Fire Alarm system and its associated components included but not limited: The Automatic Initiating Devices including the smoke detectors, Air sampling, Duct smoke detectors, sprinkler water flow switches (wet/dry) and C/O Detectors. The Manual Initiating Devices including the manual pull stations and the warden stations. The Notification Devices including the speakers, the speakers/strobes and the strobe lights. The Life Safety Functions including the Electro-Mechanical device (HVAC shutdown, Elevator recall, Door release, etc.) The Interface Equipment including the main fire control panel, remote control panels (AMP & power rack, strobe control panels, sub-systems, RUT/DGP/TTB, ETC.) and the fire pump monitoring modules. Failure to do so shall result in the contractor being subject to the assessment of liquidated damages of $100.00 per day.
Sample 1

Related to Automatic and Manual Fire Fighting Equipment

  • Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.

  • Computer Equipment Recycling Program If this Contract is for the purchase or lease of computer equipment, then Contractor certifies that it is in compliance with Subchapter Y, Chapter 361 of the Texas Health and Safety Code related to the Computer Equipment Recycling Program and the Texas Commission on Environmental Quality rules in 30 TAC Chapter 328.

  • Additional Equipment Additional Equipment may from time to time be added as the subject matter of this Agreement as agreed on by the parties. Any additional property will be added in an amendment describing the property, the monthly rental, security deposit, and stipulated loss value of the additional Equipment. All amendments must be in writing and signed by both parties. Other than by this amendment procedure, this Agreement may not be amended, modified, or altered in any manner except in writing signed by both parties.

  • STANDARD EQUIPMENT All items of standard equipment which are provided by the OEM shall be furnished unless such items are expressly deleted by the Authorized User or are specified to be other than standard in the Mini-Bid. When Optional equipment is specified, all components listed in the OEM’s data book as being included with the Option shall be furnished.

  • Collocation of Switching Equipment CLEC may collocate any equipment that is necessary for Interconnection or access to Unbundled Network Elements.

  • SPECIAL TOOLS & TEST EQUIPMENT If the price stated on the Offer includes the cost of any special tooling or special test equipment fabricated or required by the Contractor for the purpose of filling this order, such special tooling equipment and any process sheets related thereto shall become the property of the City and shall be identified by the Contractor as such.

  • Filing Systems and Equipment A complete and comprehensive catalog of filing systems including vertical and lateral files, bookcases, mobile cabinets and freestanding file cabinets.

  • Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract.

  • Service Location and Equipment The AGENCY must request in writing and said request must be approved in writing by the COUNTY’S Manager of the CCC or designee, prior to any change in the dates, times, and locations of services provided in this Contract.

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

Time is Money Join Law Insider Premium to draft better contracts faster.