DIAMETER Sample Clauses

DIAMETER. Diameter of water main shall be designed to deliver water in adequate quantities and pressures for domestic use under peak consumption conditions and fire fighting in accordance with these Standards. Standard water main diameters shall be 2½ (except Hawaii and Maui), 3 (Kauai only), 4, 6, 8, 12,16, 18 (except Oahu), 20, 24, 30, 36 and 42-inches. For Kauai Only: The minimum water main diameter shall be 6-inches. The water main diameter may be reduced after the last fire hydrant. Mains less than 6-inches in diameter shall be Ductile Iron Cl. 52, PVC C900 Cl. 150 or 200, brass pipe or copper tubing. 102.05 TYPE, CLASS. Types and classes of mains are as shown in Table 100-4. Table 100-4 - TYPES AND CLASSES OF MAINS Island Ductile Iron Cl. 52 Concrete Cylinder Cl. 150 Or 250 Cl. 150 or 200 PVC C900 Cl. 150 PVC C905 Hawaii 1,10 NA NA NA Kauai 1,8 NA 7 NA Maui 1,4,8 3,4 NA NA Oahu 1,4,9 4,5 2,4 4,6 1 - Mains 4-inch through 42-inch in diameter. 2 - Mains 4-inch through 12-inch in diameter (Cl. 150 = DR 18, Cl. 200 = DR 14). 3 - Mains 30-inch in diameter or larger.
Sample 1Sample 2Sample 3
AutoNDA by SimpleDocs
DIAMETER. In the case where the diameter of the reels is specified in the order and where this requirement has been accepted by the vendor, the tolerance concerning variation in diameter is for papers or boards based on the tolerances set out in the GSC. Reels coming at the end of the parent reel of the last consignment will nevertheless have to be accepted by the Buyer provided that their diameters are more than half of the diameters ordered.
Sample 1Sample 2
DIAMETER. (a) Subject to Clause 3.2(b) of this Schedule 3, the minimum diameter is ten centimetres, measured under bark.
Sample 1
DIAMETER. The minimum acceptable diameter is 3.0 inches. The maximum acceptable diameter is 20.0 inches anywhere along the stick of wood (including knots, limbs, xxxxx, sweep, etc.)
Sample 1
DIAMETER. In the case where the diameter of the reels is specified in the order and where this requirement has been accepted by the vendor, the tolerance concerning variation in diameter is: - for papers  where there is no stipulation of max or min diameter: - 4 cm and + 2 cm  where minimum diameter is stipulated: + 4 cm  where maximum diameter is stipulated: - 8 cm  for bulk papers, special arrangements may be made. - for boards  where there is no stipulation of max or min diameter: ±6 cm  where minimum diameter is stipulated: + 12 cm  where maximum diameter is stipulated: - 12 cm Reels coming at the end of the parent reel of the last consignment will nevertheless have to be accepted by the Buyer provided that their diameters are more than half of the diameters ordered.
Sample 1

Related to DIAMETER

  • Speed The relative importance we attach is “high”.

  • Generator Subject to the provisions of this Section 29.36, Tenant shall be entitled to install, operate and maintain a generator and any other equipment related thereto, including, without limitation, a fuel system, wiring and shaft space (“Generator”) next to the Building at Tenant’s sole cost and expense (without paying any additional fee or rental to Landlord for the use thereof). Prior to the installation of the Generator, Tenant shall inspect the proposed location to determine a suitable location for the Generator, and Tenant shall submit written plans and specifications relative to the type, size and proposed location (including any proposed screening) of the Generator to Landlord for its review and written approval. Tenant shall be solely responsible for the cost of acquisition, installation, operation, and maintenance of the Generator; and Tenant shall install, maintain and operate the Generator in accordance with all federal, state, and local laws, statutes, ordinances, rules and regulations, including without limitation, obtaining and maintaining any and all permits, approvals and licenses required to install and operate the Generator by any governmental authority having jurisdiction. Landlord and Tenant agree that, upon the expiration of earlier termination of the Lease Term, Tenant shall not be required to remove the Generator, any associated cabling, wiring and screening or other improvements. Tenant shall not be entitled to grant or assign to any third party (other than a permitted assignee of Tenant’s rights under the Lease or a permitted subtenant relative to the Premises (or a portion thereof)) the right to use the Generator without Landlord’s prior written consent (which consent may be granted or withheld in Landlord’s discretion). Upon reasonable advance notice to Tenant (and provided Landlord reasonably coordinates with Tenant and provides an alternate source of backup generator capacity during said transition), Landlord shall be entitled to cause the Generator to be moved to another location near the Building, at Landlord’s cost and expense. Tenant shall pay all personal property taxes on the Generator. Tenant shall also pay any increases in the real property taxes of the Building due to the installation of the Generator within thirty (30) days of receipt of notice from Landlord which includes proof of such increase in taxes. Tenant’s indemnity obligations under Section 5.4.1.5 of the Lease, relating to the use of Hazardous Materials, shall apply to the use and operation of the Generator. Finally, Tenant’s insurance obligations under Section 10.3 of the Lease shall apply to the Generator.

  • Transponders will be assigned to each covert vehicle and are to be stored in the glove compartment, console or other secure place within the assigned vehicle when not in use.

  • Walls 12 Developer shall provide rustication patterns on all walls, except drainage headwalls, in Aesthetic 13 Area 3 in accordance with Exhibit L2.24 of the LAADCR. The final designs shall resemble these 14 simulations.

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Floor Loading Floor loading capacity shall be within building design capacity. Tenant may exceed floor loading capacity with Landlord’s consent, at Landlord’s sole discretion and must, at Tenant’s sole cost and expense, reinforce the floor as required for such excess loading.

  • Electrical Provide drawings for the following systems:

  • GLASS The Tenant shall maintain the glass part of the demised premises, promptly replacing any breakage and fully saving the Landlord harmless from any loss, cost or damage resulting from such breakage or the replacement thereof.

  • NIGHTLY a. All floors in Group A to be swept, wet mopped and rinsed.

  • Ceilings 13.1 Lambdaboard ceilings, minimum 25mm thick with a width of 1220mm x 1800mm, skimmed with Plascon EZ Joint and EZ Skim system.

Time is Money Join Law Insider Premium to draft better contracts faster.