MEASUREMENTS AND READINGS Sample Clauses

MEASUREMENTS AND READINGS. 8.1. The Carrier will be required to perform a quality control check of the gas at the Entry Point and Point of Exit at the Regasification Plant. The Contractor will be responsible to make sure that the LNG is checked for the required quality levels before it arrives at the Point of Entry of the Regasification Plant, to make sure that the LNG complies with the standards of quality required by current regulations.
Sample 1Sample 2Sample 3See All (4)
AutoNDA by SimpleDocs
MEASUREMENTS AND READINGS. 8.1 The amounts supplied at the entry points will be measured by means of the measurement devices located at the points themselves, in accordance with the procedures set forth in the Technical System Management Regulations, as well as in its Detail Protocols, which will include the requirements for carrying out the necessary checks on the running of the measurement units, how often they are to be performed and the measures to adopt in the event that the units malfunction. The measurement systems shall be suitable to maximum hourly flow rate provided for consumers qualified as specified in Regulation Public Service Gas Fuels Standards Technical Management System and its Protocols of Detail.
Sample 1Sample 2
MEASUREMENTS AND READINGS. 8.1. The Contractor will be required, before the gas enter the system, to perform the necessary measurements of quality to assure that it meets the quality specifications established in the current regulation.
Sample 1
MEASUREMENTS AND READINGS. 8.1 The amounts supplied at the entry points will be measured by means of the measurement devices located at the points themselves, in accordance with the procedures set forth in the Technical Management Regulations of the Gas System, as well as in its Detail Protocols, which will include the requirements for carrying out the necessary checks on the running of the measurement units, how often they are to be performed and the measures to adopt in the event that the units malfunction.
Sample 1

Related to MEASUREMENTS AND READINGS

  • Measurements and Dimensions Before ordering material or doing work that is dependent upon coordination with building conditions, the Contractor shall verify all dimensions, elevations, grades, and pitch by taking measurements at the building and shall be responsible for the correctness of same. Any discrepancies between the drawings and/or specifications and the existing conditions shall be referred to the Design Professional for additional instructions before any work affected thereby is begun.

  • Measurements All production shall be accurately measured using standards established by the American Gas Association (AGA) and/or the American Petroleum Institute (API) and all measuring devices shall be tamper proof as nearly as possible. Oil royalties due within the terms of this lease shall be calculated on actual and accurate measurements within API standards unless a different means of measurement, subject to Lessor's approval, is provided.

  • DOCUMENTS AND SAMPLES AT THE SITE 4.11.1 The Contractor shall maintain at the site for the State one record copy of all Drawings, Specifications, Addenda, Change Orders and other modifications, in good order and marked currently to record all changes made during construction, and approved Shop Drawings, Product Data and Samples. These shall be available to the Architect and the State for monthly review prior to approval of Contractor’s monthly application for payment. Prior to substantial completion of the Work, the Contractor shall ensure that one record copy of all Drawings, Specifications, Addenda, Change Orders and other Modifications, in good order and marked currently to record all changes made during construction, and approved Shop Drawings, Product Data and Samples are delivered to the Architect for the State and a duplicate copy shall be delivered to the State for the State’s use.

  • Measurements and arithmetic conventions All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.

  • GEOGRAPHIC AREA AND SECTOR SPECIFIC ALLOWANCES, CONDITIONS AND EXCEPTIONS The following allowances and conditions shall apply where relevant: Where the company does work which falls under the following headings, the company agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.

  • Payments and Completion Payments may be withheld because of (1) defective work not remedied; (2) failure of contractor to make proper payments to subcontractors, workers, or suppliers; (3) persistent failure to carry out work in acceptance with this Agreement or these general conditions, or (4) legal claims. Final payment will be due after complete release of any and all liens arising out of the contract or submission of receipts or other evidence of payment covering all subcontractors or suppliers who could file such a lien. The contractor agrees to indemnify the Owner against such liens and will refund all monies including costs and reasonable attorney’s fees paid by the owner in discharging the liens. A 10 percent holdback is required by the lender to assure the work has been properly completed and there are no liens against the property. Owners Initials: Contractor’s Initials: -Continued on Page Three-

  • Measurement and Billing The Parties shall measure Interconnection in accordance with this Section 4.6 and xxxx in accordance with Article XXVII and this Section 4.6.

  • PERFORMANCE MEASUREMENTS Upon a particular Commission’s issuance of an Order pertaining to Performance Measurements in a proceeding expressly applicable to all CLECs generally, BellSouth shall implement in that state such Performance Measurements as of the date specified by the Commission. Performance Measurements that have been Ordered in a particular state can currently be accessed via the internet at xxxx://xxxx.xxxxxxxxx.xxx. The following Service Quality Measurements (SQM) plan as it presently exists and as it may be modified in the future, is being included as the performance measurements currently in place for the state of Tennessee. At such time that the TRA issues a subsequent Order pertaining to Performance Measurements, such Performance Measurements shall supersede the SQM contained in the Agreement. BellSouth Service Quality Measurement Plan‌ (SQM) Tennessee Performance Metrics Measurement Descriptions Version 2.00 Issue Date: July 1, 2003 Introduction

  • Meter Readings If applicable, the Customer shall provide accurate and timely meter readings at the end of each applicable billing period on the forms or other alternative means specified by Vendor. Vendor shall have the right, upon reasonable prior notice to Customer, and during Customer’s regular business hours, to inspect the equipment and to monitor the meter readings. If Customer meter readings are not received in the time to be agreed upon by the parties, the meter readings may be obtained electronically or by other means or may be estimated by Vendor subject to reconciliation when the correct meter reading is received by Vendor.

  • Skills and Abilities (i) Ability to communicate effectively both verbally and in writing.

Time is Money Join Law Insider Premium to draft better contracts faster.