Purpose and background for the SOP Sample Clauses

Purpose and background for the SOP. The purpose of this SOP is to describe in detail a simple and robust procedure to quantify the amount of volatile, oxidizable and/or decomposable organic matter present on the surface of and/or in a MNM using TGA. This SOP complies with the ASTM standard E1131 and is consistent with the ASTM standards E2040 and E2402, and with the International Confederation for Thermal Analysis and Calorimetry (ICTAC) recommendations of the International Union of Pure and Applied Chemistry (Lever et al. 2014); it was prepared in collaboration with all partners participating in deliverable D2.4 of the NANoREG project.
Sample 1
AutoNDA by SimpleDocs
Purpose and background for the SOP. This SOP facilitates a simple and robust procedure to identify MNM that may contain volatile, oxidizable and/or decomposable organic and inorganic matter, which can be present on the surface of and/or within porosities of a MNM or other individual phases in mixture (e.g., additives, dispersants and process impurities). The procedure is based on weighing and heating in a drying oven and a laboratory furnace. The SOP serves as a low cost alternative to thermogravimetric analysis (TGA) and builds on several laboratory procedures developed over time considering several procedures for mineral, rock, and material analysis. The specific description in this SOP, was based on the loss-on-ignition (LOI) method applied on sediments by Xxxxx et al., (2001). The SOP was prepared in collaboration with all partners participating in deliverable D2.4 of the NANoREG project.
Sample 1
Purpose and background for the SOP. The purpose of this SOP is to describe in detail a simple and robust procedure for semi- quantitative determination of the chemical composition of nanomaterials collected on a filter, dispersed in a liquid or as a powder.
Sample 1
Purpose and background for the SOP. The purpose of this SOP is to enable reliable procedures for identification of organic substances which can be extracted from MNM and analyzed with mass spectrometry (MS). The SOP do not describe an easy-to-use procedure since the often unknown organic coating can consist of anything from relative small volatile molecules to polymeric compounds which may be bound by a range of different forces such as Van der Walls forces, electrostatic forces, and ionic bindings. The procedures described in the SOP require an operator with great experience in the techniques used. The procedures describes in a general manner how the extractions and analyzes can be performed. The SOP is based on results in Nymark et al. (2013) and a publication in preparation (Xxxxxxx et al., 2015) and is developed in collaboration with the partners in deliverable D 2.4 in the NANoREG project. It is a prerequisite for this SOP that TGA and/or XRF have indicated organic substance in association with the MNM under investigation. The amount of the organic compounds associated with the MNM is determined by TGA.
Sample 1
Purpose and background for the SOP. The purpose of this SOP is to enable reliable procedures for identification and quantification of inorganic coatings on the surface of MNMs by Transmission Electron Microscopy (TEM). The SOP do not describe an easy-to-use procedure since the often unknown inorganic coating can consist of almost any element and/or combinations of elements. The procedures described in the SOP require an operator with great experience in the techniques used. The SOP is prepared in collaboration with the partners in deliverable D 2.4 in the NANoREG project. It is a prerequisite for this SOP that XRF have identified two or several elements in amounts that indicate a possible inorganic coating on the MNM under investigation. The primary purpose of Scanning Transmission Electron Microscopy (STEM) is to identify and quantify inorganic coating/secondary phases that can be found in MNMs, both by carrying out imaging (TEM/STEM) as well as by employing analytical methods (EDS, EELS etc.).
Sample 1
Purpose and background for the SOP. The purpose of this SOP is to enable an easy-to-use and still reliable procedure for quantification of oxygen containing functional groups on the side-walls of CNT using thermogravimetric analysis (TGA) with a detector suitable for CO and CO2, and H2O. The SOP is based on results in Xxxxxxx et al. (2015) and a publication in preparation (Xxxxxxx, 2015) and developed in collaboration with the partners in deliverable D
Sample 1

Related to Purpose and background for the SOP

  • Purpose and Background 1.00─Purpose and Background

  • Interested Party for the purpose of filing a dispute relating to a solicitation, as used in this section, means an actual or prospective bidder or offeror whose direct economic interest would be affected by the award of a Contract or by the failure to award a Contract.

  • EVENTS CONSTITUTING MATERIAL BREACH OF AGREEMENT The Applicant shall be in Material Breach of this Agreement if it commits one or more of the following acts or omissions (each a “Material Breach”):

  • REPRESENTATIONS AND WARRANTIES OF ANNUAL CONFERENCE The Annual Conference represents and warrants to the Local Church as of the date hereof and the Disaffiliation Date as follows:

  • Background Screening VENDOR shall comply with all requirements of Sections 1012.32 and 1012.465, Florida Statutes, and all of its personnel who (1) are to be permitted access to school grounds when students are present, (2) will have direct contact with students, or (3) have access or control of school funds, will successfully complete the background screening required by the referenced statutes and meet the standards established by the statutes. This background screening will be conducted by SBBC in advance of VENDOR or its personnel providing any services under the conditions described in the previous sentence. VENDOR shall bear the cost of acquiring the background screening required by Section 1012.32, Florida Statutes, and any fee imposed by the Florida Department of Law Enforcement to maintain the fingerprints provided with respect to VENDOR and its personnel. The parties agree that the failure of VENDOR to perform any of the duties described in this section shall constitute a material breach of this Agreement entitling SBBC to terminate immediately with no further responsibilities or duties to perform under this Agreement. VENDOR agrees to indemnify and hold harmless SBBC, its officers and employees from any liability in the form of physical or mental injury, death or property damage resulting from VENDOR’s failure to comply with the requirements of this section or with Sections 1012.32 and 1012.465, Florida Statutes.

  • Introduction and Background 1.1 The purpose of this Schedule 2 (Contract Services and Contract Supplies) is to set out the characteristics of the Contract Services and/or Contract Supplies (as the case may be) and Funding that the Provider will be required to make available to all Contracting Authorities in relation to Lot 1 and/or Lot 2 (as the case may be) and to provide a description of what the Contract Services and/or Contract Supplies (as the case may be) and Funding will entail.

  • Purpose and Scope of the Agreement The scope of this Agreement is to set out the rules, terms and principles according to which each Partner shall commit himself on the following points:

  • Purpose and Applicability (a) The purpose of this Exhibit is to provide a description of Part 504 of NYSERDA’s regulations, which consists of NYSERDA’s policy for making payment promptly on amounts properly due and owing by NYSERDA under this Agreement. The section numbers used in this document correspond to the section numbers appearing in Part 504 of the regulations.2

  • PURPOSE AND SCOPE OF AGREEMENT 1.01 The purpose of this Agreement is to maintain harmonious and mutually beneficial relationships between the Employer, the Union and the employees and to set forth herein certain terms and conditions of employment upon which agreement has been reached through collective bargaining.

  • Purpose and Application This document (“DPA”) is incorporated into the Agreement and forms part of a written (including in electronic form) contract between SAP and Customer. This DPA applies to Personal Data processed by SAP and its Subprocessors in connection with its provision of the Cloud Service. This DPA does not apply to non-production environments of the Cloud Service if such environments are made available by SAP, and Customer shall not store Personal Data in such environments.

Time is Money Join Law Insider Premium to draft better contracts faster.