Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Switching and Tagging Rules Each Party shall provide the other Parties a copy of its switching and tagging rules that are applicable to the other Parties’ activities. Such switching and tagging rules shall be developed on a non-discriminatory basis. The Parties shall comply with applicable switching and tagging rules, as amended from time to time, in obtaining clearances for work or for switching operations on equipment.
Scheduling i) The designated employer will provide the employee with their schedule of shifts in accordance with the collective agreement for both homes. [Insert the split/sharing of shift numbers here] Similarly, the employee will submit all requests for time off including vacation to the designated employer in accordance with the collective agreement. ii) Posted schedules will include home identification. An employee will only be scheduled in one home per shift. iii) Overtime payment and other premiums will be in accordance with the collective agreement of the designated employer. iv) Weekends off, consecutive work days and all other scheduling provisions will be in accordance with the collective agreement at the designated employer.
Work Scheduling Except at the request of an affected employee, no employee shall have the number of hours they are normally scheduled to work reduced as the result of the use of non-permanent employees such as, but not limited to: seasonal, intermittent, student interns, interns, interim, established term, or temporary employees, due to the performance of such employee’s duties by the nonpermanent employee.
Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.
Packing and Marking All material and equipment to be furnished by the Contractor shall be packed, crated or otherwise suitably protected to withstand shipment undamaged to the destination. Each package, crate or part shall be marked plainly with the name of the consignee, shipping destination, the Owner's order number, and such other markings as are required. Complete packing lists, one copy with each package and two (2) copies by mail to the Owner at time of shipment, shall be supplied showing contents and identity of each package.
Ordering and Provisioning 53.3.1 CenturyLink will provide necessary ordering and provisioning business process support as well as those technical and systems interfaces as may be required to enable CLEC to provide resale services, including the functions, features, and capabilities of such services, and Unbundled Network Elements. If CenturyLink deploys any enhanced electronic capability CenturyLink will notify CLEC of availability and CLEC shall use the processes for performing transaction(s) to the extent practicable and the use of any other interface or process will be discontinued. 53.3.2 The Parties agree that orders for services under this Agreement will not be submitted or accepted until thirty (30) Days after the completion of all account establishment activities, including but not limited to, the documents and information subscribed in Section 45.1, unless the Parties mutually agree upon a different date based on the specific circumstances of the Parties’ relationship. 53.3.3 Except as specifically provided otherwise in this Agreement, pre- ordering, ordering and provisioning of resold services shall be governed in accordance with CenturyLink’s Standard Practices. 53.3.4 CenturyLink will provide provisioning intervals and procedures for design and complex services on a nondiscriminatory basis. Complex Service Order charges pursuant to Tariff terms may apply. 53.3.5 Where Technically Feasible, the NEAC will coordinate support for all designed and/or complex services provided to CLEC. 53.3.6 To the extent required by Applicable Law, and upon request from CLEC, employing CenturyLink’s LSR, CenturyLink will provide blocking of 700, 900, and 976 services, or other services of similar type as may now exist or be developed in the future, and shall provide Billed Number Screening (BNS), including required LIDB updates, or equivalent service for blocking completion of bill-to-third party and collect calls, on a line, PBX, or individual service basis. Blocking shall be provided to the extent (a) it is an available option for the Telecommunications Service resold by CLEC, or (b) it is Technically Feasible when requested by CLEC as a function of Unbundled Network Elements. 53.3.7 When ordering a resale service via an LSR Service Order, CLEC may order separate interLATA and IintraLATA service providers (i.e., two PICs) on a line or trunk basis, and CLEC agrees to pay the applicable Service Order and PIC charges associated with such order. CenturyLink will accept PIC change orders for IntraLATA toll and long distance services through the service provisioning process. 53.3.8 The standard Service Order charges as listed in the Table 1 of this Agreement shall apply to all orders.
Scheduling Vacations Vacations are to be scheduled in advance and taken at such reasonable times as approved by the employee's department with particular regard to the needs of the Employer, seniority of employee, and, insofar as practicable, with regard to the wishes of the employee. No vacation shall be assigned by the Employer or deducted from the employee's account as disciplinary action.
Training and Promotion a. The contractor will assist in locating, qualifying, and increasing the skills of minorities and women who are applicants for employment or current employees. Such efforts should be aimed at developing full journey level status employees in the type of trade or job classification involved. b. Consistent with the contractor's work force requirements and as permissible under Federal and State regulations, the contractor shall make full use of training programs, i.e., apprenticeship, and on-the-job training programs for the geographical area of contract performance. In the event a special provision for training is provided under this contract, this subparagraph will be superseded as indicated in the special provision. The contracting agency may reserve training positions for persons who receive welfare assistance in accordance with 23 U.S.C. 140(a). c. The contractor will advise employees and applicants for employment of available training programs and entrance requirements for each. d. The contractor will periodically review the training and promotion potential of employees who are minorities and women and will encourage eligible employees to apply for such training and promotion.
Maintenance Scheduling The NTO shall schedule maintenance of its facilities designated as NTO Transmission Facilities Under ISO Operational Control and schedule any outages (other than forced transmission outages) of said transmission system facilities in accordance with outage schedules approved by the ISO. The NTO shall comply with maintenance schedules coordinated by the ISO, pursuant to this Agreement, for NTO Transmission Facilities Under ISO Operational Control. The NTO shall be responsible for providing notification of maintenance schedules to the ISO for NTO Transmission Facilities Requiring ISO Notification. The NTO shall provide notification of maintenance schedules to affected Transmission Owners for NTO Transmission Facilities Requiring ISO Notification and Local Area Transmission Facilities pursuant to Section 3.5.3 of the ISO Services Tariff.