Specification and Airworthiness Approvals Sample Clauses

Specification and Airworthiness Approvals. The Buyer will ensure that all Buyer Furnished Equipment will meet the requirements of the Specifications, will comply with applicable DGAC and FAA regulations and will be approved by the DGAC and the FAA for installation and use on an Aircraft at the time of delivery of such Aircraft. The Seller will bear no expense in connection with adjusting and calibrating Buyer Furnished Equipment to the extent necessary to obtain DGAC and FAA approval, unless such adjusting and calibrating is made necessary by improper installation by the Seller of the Buyer Furnished Equipment.
AutoNDA by SimpleDocs
Specification and Airworthiness Approvals. Northwest warrants that all Buyer Furnished Equipment (other than Buyer Furnished Equipment manufactured by the Manufacturer) will meet the requirements of the Specification, will comply with applicable LBA and FAA regulations and will be approved by the LBA and the FAA for installation and use on an Aircraft at the time of delivery of such Aircraft. AVSA will bear no expense in connection with adjusting and calibrating Buyer Furnished Equipment to the extent necessary to obtain LBA and FAA approval, unless such work is due to an Aircraft Interface Problem, mishandling or excessive use on the part of AVSA or the Manufacturer.
Specification and Airworthiness Approvals. The Buyer warrants that all Buyer Furnished Equipment will meet the requirements of the applicable Aircraft Specification, will comply with applicable EASA, FAA and Alternative Airworthiness Authority regulations and will be approved by the EASA, FAA and Alternative Airworthiness Authority, as applicable, for installation and use on an Aircraft at the time of Delivery of such Aircraft. The Seller will bear no expense in connection with adjusting and calibrating Buyer Furnished Equipment to the extent necessary to obtain EASA, FAA and Alternative Airworthiness Authority approval.
Specification and Airworthiness Approvals. The Buyer will ensure that all Buyer Furnished Equipment will meet the requirements of the Specifications, will comply with applicable LBA, for A319 Aircraft and A321 Aircraft, DGAC, for A320 Aircraft, and FAA regulations and will be approved by the LBA, DGAC, and the FAA for installation and use on an Aircraft at the time of delivery of such Aircraft. The Seller will bear no expense in connection with adjusting and calibrating Buyer Furnished Equipment to the extent necessary to obtain LBA, DGAC and FAA approval, unless such adjusting and calibrating is made necessary by improper installation by the Seller of the Buyer Furnished Equipment.

Related to Specification and Airworthiness Approvals

  • Hardware and Software Requirements In order to access and retain Disclosures electronically, you must satisfy the following computer hardware and software requirements: access to the Internet; an email account and related software capable of receiving email through the Internet; a web browser which is SSL-compliant and supports secure sessions, and hardware capable of running this software.

  • Changes to Specifications All Specifications and any changes thereto agreed to by the parties from time to time shall be in writing, dated and signed by the parties. Any change to the Process shall be deemed a Specification change. No change in the Specifications shall be implemented by Catalent, whether requested by Client or requested or required by any Regulatory Authority, until the parties have agreed in writing to such change, the implementation date of such change, and any increase or decrease in costs, expenses or fees associated with such change (including any change to Unit Pricing). Catalent shall respond promptly to any request made by Client for a change in the Specifications, and both parties shall use commercially reasonable, good faith efforts to agree to the terms of such change in a timely manner. As soon as possible after a request is made for any change in Specifications, Catalent shall notify Client of the costs associated with such change and shall provide such supporting documentation as Client may reasonably require. Client shall pay all costs associated with such agreed upon changes. If there is a conflict between the terms of this Agreement and the terms of the Specifications, this Agreement shall control. Catalent reserves the right to postpone effecting changes to the Specifications until such time as the parties agree to and execute the required written amendment.

  • Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).

  • APPROVAL OF PLANS AND SPECIFICATIONS The Plans and Specifications will conform to the requirements and conditions set out by applicable law or any effective restrictive covenant, and to all governmental authorities which exercise jurisdiction over the Leased Premises or the construction thereon.

  • Specifications Shipper will ensure that all of its Products tendered at the Origin Point for transportation on the Pipeline System meet the applicable specifications for the Product as set forth in the Tariff (as defined below) (the “Specifications”).

  • Compliance with Regulatory Requirements Upon demand by Lender, Borrower shall reimburse Lender for Lender’s additional costs and/or reductions in the amount of principal or interest received or receivable by Lender if at any time after the date of this Agreement any law, treaty or regulation or any change in any law, treaty or regulation or the interpretation thereof by any Governmental Authority charged with the administration thereof or any other authority having jurisdiction over Lender or the Loans, whether or not having the force of law, shall impose, modify or deem applicable any reserve and/or special deposit requirement against or in respect of assets held by or deposits in or for the account of the Loans by Lender or impose on Lender any other condition with respect to this Agreement or the Loans, the result of which is to either increase the cost to Lender of making or maintaining the Loans or to reduce the amount of principal or interest received or receivable by Lender with respect to such Loans. Said additional costs and/or reductions will be those which directly result from the imposition of such requirement or condition on the making or maintaining of such Loans.

  • Listing and Maintenance Requirements Compliance The Company has not in the two years preceding the date hereof received written notice from any stock exchange, market or trading facility on which the Common Stock is or has been listed or quoted to the effect that the Company is not in compliance with the listing, maintenance or other requirements of such exchange, market, trading or quotation facility. The Company has no reason to believe that it does not now or will not in the future meet any such requirements.

  • Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.

  • Compliance with Law; Governmental Approvals Each of the Borrower, the other Loan Parties and the other Subsidiaries is in compliance with each Governmental Approval and all other Applicable Laws relating to it except for noncompliances which, and Governmental Approvals the failure to possess which, could not, individually or in the aggregate, reasonably be expected to cause a Default or Event of Default or have a Material Adverse Effect.

  • Compliance with Law; Governmental Authorizations To the best of Seller’s knowledge, Seller is in compliance with all federal, state and local laws, authorizations, licenses and permits of any governmental authority and all governmental orders affecting the properties and assets of Seller, including federal, state and local: (i) Occupational Safety and Health Laws; (ii) private investigatory and other similar laws; (iii) the Fair Credit Reporting Act and similar state and local laws; and (iv) laws regarding or relating to trespass or violation of privacy rights. Seller has not been charged with violating, nor to the knowledge of Seller, threatened with a charge of violating, nor, to the knowledge of Seller, is Seller under investigation with respect to a possible violation of any provision of any federal, state or local law relating to any of, properties or assets.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!