SQF Sample Clauses

SQF. Where a Certified Organization’s business has been sold and the business name is retained, the new owner must, within thirty (30) days of the change of ownership, notify PJRFSI.
AutoNDA by SimpleDocs
SQF. The Organization is responsible for creating a Supplier record in the SQFI database in order to register for their Certification Audit. The Organization is also responsible for re-registering in the SQFI database as needed for all future audits.
SQF. Details of the Organization’s Certificate of Registration will be made available on the SQFI website for public display as follows: supplier name, state/province, country, Accreditation Body logo and accreditation number, certificate type and number, certification level, audit date, date of next audit, date of issue, certification expiry date, food sector category(s), product(s) covered by the Certificate of Registration, and modules implemented.
SQF on the Flooron all the floors, without provision of for any lift/elevator and without any separate garage or covered parking (For Flat)(hereinafter referred to as the “Plots/Flats/Duplex,” more particularly described in Schedule A and the floor plan of the Plots/Flats/Duplex,is annexed hereto and marked as Schedule B);

Related to SQF

  • Slope Portions of an accessible route with running slopes steeper than 1:20 are ramps and shall comply with 4.8. The cross slope of an accessible route shall not be steeper than 1:48  See Figure 1 for required compliance  Near Unit #612: o grind, relevel or repour concrete curb ramp to 8.33% grade or less on slope

  • Basement Any leaks or evidence of moisture? Yes No Unknown Does Not Apply Comments:

  • Rate Center Area The geographic area that has been identified by a given LEC as being associated with a particular NPA-NXX code assigned to the LEC for its provision of Telephone Exchange Services. The Rate Center Area is the exclusive geographic area that the LEC has identified as the area within which it will provide Telephone Exchange Services bearing the particular NPA-NXX designation associated with the specific Rate Center Area.

  • Width 6.7.4.1.1. The minimum width at the child-restraint straps which contact the dummy shall be 25 mm. These dimensions shall be measured during the strap strength test prescribed in paragraph 7.2.5.1. below, without stopping the machine and under a load equal to 75 per cent of the breaking load of the strap.

  • SUBLOOPS 45.1. Sprint will offer unbundled access to copper subloops and subloops for access to multiunit premises wiring. Sprint will consider all requests for access to subloops through the ICB process due to the wide variety of interconnections available and the lack of standards. A written response will be provided to CLEC covering the interconnection time intervals, prices and other information based on the ICB process as set forth in this Agreement.

  • Elevation Elevation is defined as restoring an employee to the higher classification, with permanent status, which was held prior to being granted a demotion or to a class that is between the current class and the class from which the employee was demoted. Upon elevation, an employee’s salary will be determined in the same manner that is provided for promotion in Section 43.5, above.

  • DS3 Loop DS3 Loop is a two-point digital transmission path which provides for simultaneous two-way transmission of serial, bipolar, return-to-zero isochronous digital electrical signals at a transmission rate of 44.736 megabits per second (Mbps) that is dedicated to the use of the ordering CLEC in its provisioning of local exchange and associated exchange access services. It may provide transport for twenty-eight (28) DS1 channels, each of which provides the digital equivalent of twenty-four (24) analog voice grade channels. The interface to unbundled dedicated DS3 transport is a metallic-based electrical interface.

  • Ceiling Company and its subcontractors will not affix, attach, or suspend any lighting fixtures, signs, or other fixtures or devices of any kind or nature from the ceiling above any of the Premises without the prior written approval of Authority.

  • ROAD DIMENSIONS Purchaser shall perform road work in accordance with the dimensions shown on the TYPICAL SECTION SHEET and the specifications within this road plan.

  • CURVE WIDENING The minimum widening placed on the inside of curves is:  6 feet for curves of 50 to 79 feet radius.  4 feet for curves of 80 to 100 feet radius.

Time is Money Join Law Insider Premium to draft better contracts faster.