Typical testing layouts Sample Clauses

Typical testing layouts. Microtremor measurements in 2D array configuration were carried out using sensors inter- distances between 5 m and about 250 m (Figure 8). The stations worked contemporary for more than 1 hour (Table 2), recording noise at 200 s.p.s. (only at BVG 500 s.p.s. was used), which is adequate for the short inter-station distance considered. Sensors were installed so as to obtain a good coupling between the instrument and soil, and where possible, avoiding asphalt. Moreover sensors were covered in order to reduce any interference caused by wind.
Sample 1
AutoNDA by SimpleDocs

Related to Typical testing layouts

  • Training a. The employer, in consultation with the local, shall be responsible for developing and implementing an ongoing harassment and sexual harassment awareness program for all employees. Where a program currently exists and meets the criteria listed in this agreement, such a program shall be deemed to satisfy the provisions of this article. This awareness program shall initially be for all employees and shall be scheduled at least once annually for all new employees to attend.

  • Scope of Services The specific scope of work for each job shall be determined in advance and in writing between TIPS Member, Member’s design professionals and Vendor. It is permitted for the TIPS Member to provide a general scope description, but the awarded vendor should provide a written scope of work, and if applicable, according to the TIPS Member’s design Professional as part of the proposal. Once the scope of the job is agreed to, the TIPS Member will issue a PO and/or an Agreement or Contract with the Job Order Contract Proposal referenced or as an attachment along with bond and any other special provisions agreed by the TIPS Member. If special terms and conditions other than those covered within this solicitation and awarded Agreements are required, they will be attached to the PO and/or an Agreement or Contract and shall take precedence over those in this base TIPS Vendor Agreement.

  • Hours of Work i) Where employees are now working a longer daily tour, the provisions set out in this Article governing the regular hours of work on a daily tour shall be adjusted accordingly.

  • Compassionate Leave (a) An employee is entitled to 2 days of compassionate leave for each occasion when a member of the employee's immediate family, or a member of the employee's household:

  • GRIEVANCE PROCEDURE 7.01 For purposes of this Agreement, a grievance is defined as a difference arising between the parties relating to the interpretation, application, administration or alleged violation of the Agreement including any question as to whether a matter is arbitrable.

  • PAYMENT OF WAGES With the agreement of the majority of the employees, the company may elect to pay wages weekly by electronic funds transfer (EFT) to up to two accounts of the employee’s choice.

  • HEALTH AND SAFETY C8.1 The Contractor shall promptly notify the Authority of any health and safety hazards which may arise in connection with the performance of the Contract. The Authority shall promptly notify the Contractor of any health and safety hazards which may exist or arise at the Authority’s Premises and which may affect the Contractor in the performance of the Contract.

  • Long Service Leave All employees shall be entitled to long service leave in accordance with the relevant State Legislation. The employer will ensure that any registration necessary for the purposes of portable long service schemes will be undertaken.

  • Payment Terms DXC agrees to pay Supplier the undisputed amount of an invoice within ninety (90) days after the receipt of a valid, complete and properly documented invoice. Any prompt payment discount will be calculated from the date a conforming invoice is received by DXC. Payment will be in U.S. currency unless otherwise stated. Payment will not constitute acceptance of Products and/or Services or impair DXC’s right to inspect. Acceptance shall be when DXC deems the Products and/or Services to meet its specified criteria (“Acceptance”). DXC, at its option, and without prior notice to Supplier, shall have the right to set off or deduct from any Supplier’s invoice, any credits, refunds or claims of any kind due DXC.

  • BACKGROUND 1.1. The “Work” is the research article, review article, letter, clinical trial study, report, article, or other copyright work, as identified in the Copyright Letter and further detailed in Schedule 1: Details of the Work (including such form of the copyright work submitted to Xxxxxxx Science for publication pursuant to clause 4, below), but excluding (except where context otherwise requires) any diagrams, figures or illustration specifically identified to Xxxxxxx Science pursuant to clause 3.2, below.

Time is Money Join Law Insider Premium to draft better contracts faster.