Utility's Obligation to Connect Sample Clauses

Utility's Obligation to Connect. Utility shall not be obligated to continue the electrical interconnection to the Project if it determines, in its sole discretion, that any one or more of the following conditions exist, including but not limited to: (a) those conditions listed in the Miscellaneous Operational Requirements section of the Consumer Energy Company Generator Interconnection Procedures, (b) electrical characteristics of the Project are not compatible with the electrical characteristics of Utility's distribution system, (c) the Interconnection Customer is deficient in following either the voltage schedule or reactive power schedule established by Utility, (d) an emergency condition exists on Utility’s distribution system, (e) Interconnection Customer's protective relay equipment fails, resulting in a lack of the level of protection required by prudent utility practice, (f) the Interconnection Customer’s Project is determined to be disrupting Utility customers, (g) Utility requires disconnection of the Project in order to construct, install, maintain, repair, replace, remove, investigate, inspect or test any part of Utility’s Interconnection Facilities or any other Utility equipment associated with the interconnection (also if a required component (example: communication circuit) or required modification to allow interconnection fails or becomes incapacitated and is not repaired in a timely manner), (h) by mutual consent, (i) Interconnection Customer commits a material breach of this agreement or (j) Interconnection Customer’s failure to execute this agreement or upon cancellation or termination of this agreement. Utility shall electrically connect or reconnect its distribution system to the Project when, in Utility's sole opinion, the conditions named above cease to exist. Under any of the conditions listed above, Utility will follow the procedures for disconnecting and re-connecting the interconnection as outlined in Appendix G of the appropriate Consumers Energy Company Generator Interconnection Procedures document. In the event future changes in either the (i) design or operation of the Project, (ii) federal, state or local laws, regulations or codes, (iii) Interconnection Customer’s requirements, or (iv) Utility’s requirements, necessitate additional facilities or modifications to the then existing Interconnection Facilities herein, the Parties shall undertake such additions or modifications as may be necessary. Before undertaking such future additions or modifications, the ...
AutoNDA by SimpleDocs

Related to Utility's Obligation to Connect

  • City’s Obligations A. Following the execution of this Agreement, the CITY shall begin efforts to implement the activities described in Article I of this Agreement. The failure by the CITY to develop and implement the activities described in Article I of this Agreement shall constitute a breach of this Agreement. The CITY understands and agrees that, in the event termination of this Agreement by CITY, or pursuant to Article V of this Agreement, the CITY shall reimburse the IDC the full amount of money paid by the IDC to the CITY. B. In accordance with Chapter 2264 of the Texas Government Code, the CITY agrees not to knowingly employ an undocumented worker. During the term of this Agreement, the CITY shall notify the IDC of any complaint brought against CITY alleging that it has employed undocumented workers. If the CITY, or any branch, division or department of the CITY is convicted of a violation under 8 U.S.C. Section 1324a (f), the total amount of economic development grants it has received, together with interest at the rate of five percent (5%), shall be repaid by the CITY to the IDC not later than the one hundred twentieth (120th) day after the date the IDC becomes aware of and notifies the CITY of the violation. The CITY shall not be liable for a violation of Chapter 2264 by a subsidiary, affiliate, or franchisee, or by any person with whom the CITY contracts. The CITY shall reimburse the IDC the required amount within thirty (30) days of the termination of this Agreement. The CITY further certifies that CITY is following Texas Government Code Chapter 2252 (foreign terrorist organizations prohibited), Texas Government Code Chapter 2270 (boycott-Israel), and Texas Government Code Chapter 2274, (boycotts-energy company; discrimination – firearms entity or trade association). C. The CITY shall keep and maintain complete and accurate records relating to its hiring and employment of persons, which is separate and identifiable from its other records, and shall make such records available for not less than three (3) years following termination of this Agreement. The IDC and its representatives shall be entitled to inspect said records during the term of this Agreement and for three (3) years thereafter, upon reasonable notice to the CITY. The CITY’s failure to comply with this provision will constitute a breach of the Agreement.

  • Authority’s Obligations Save as otherwise expressly provided, the obligations of the Authority under the Contract are obligations of the Authority in its capacity as a contracting counterparty and nothing in the Contract shall operate as an obligation upon, or in any other way xxxxxx or constrain the Authority in any other capacity, nor shall the exercise by the Authority of its duties and powers in any other capacity lead to any liability under the Contract (howsoever arising) on the part of the Authority to the Contractor.

  • Conditions to Company’s Obligation to Sell The obligation of Company hereunder to issue and sell the Securities to Investor at the Closing is subject to the satisfaction, on or before the Closing Date, of each of the following conditions: 5.1. Investor shall have executed this Agreement and delivered the same to Company. 5.2. Investor shall have delivered the Purchase Price to Company in accordance with Section 1.2 above.

  • CONDITIONS OF THE COMPANY'S OBLIGATION TO SELL The obligation hereunder of the Company to issue and sell the Securities to the Investor is further subject to the satisfaction, at or before each Closing Date, of each of the following conditions set forth below. These conditions are for the Company's sole benefit and may be waived by the Company at any time in its sole discretion. (A) The Investor shall have executed this Agreement and the Registration Rights Agreement and delivered the same to the Company. (B) The Investor shall have delivered to the Company the Purchase Price for the Securities being purchased by the Investor between the end of the Pricing Period and the Closing Date via a Put Settlement Sheet (hereto attached as Exhibit D). Immediately after receipt of confirmation of delivery of such Securities to the Investor, the Investor, by wire transfer of immediately available funds pursuant to the wire instructions provided by the Company, will disburse the funds constituting the Purchase Amount. (C) The representations and warranties of the Investor shall be true and correct in all material respects as of the date when made and as of the applicable Closing Date as though made at that time and the Investor shall have performed, satisfied and complied in all material respects with the covenants, agreements and conditions required by the Equity Line Transaction Documents to be performed, satisfied or complied with by the Investor on or before such Closing Date. (D) No statute, rule, regulation, executive order, decree, ruling or injunction shall have been enacted, entered, promulgated or endorsed by any court or governmental authority of competent jurisdiction which prohibits the consummation of any of the transactions contemplated by this Agreement.

  • CONDITIONS TO THE COMPANY’S OBLIGATION TO SELL The obligation of the Company hereunder to issue and sell the Note to the Buyer at the Closing is subject to the satisfaction, at or before the Closing Date of each of the following conditions thereto, provided that these conditions are for the Company’s sole benefit and may be waived by the Company at any time in its sole discretion: a. The Buyer shall have executed this Agreement and delivered the same to the Company. b. The Buyer shall have delivered the Purchase Price in accordance with Section 1(b) above. c. The representations and warranties of the Buyer shall be true and correct in all material respects as of the date when made and as of the Closing Date as though made at that time (except for representations and warranties that speak as of a specific date), and the Buyer shall have performed, satisfied and complied in all material respects with the covenants, agreements and conditions required by this Agreement to be performed, satisfied or complied with by the Buyer at or prior to the Closing Date. d. No litigation, statute, rule, regulation, executive order, decree, ruling or injunction shall have been enacted, entered, promulgated or endorsed by or in any court or governmental authority of competent jurisdiction or any self-regulatory organization having authority over the matters contemplated hereby which prohibits the consummation of any of the transactions contemplated by this Agreement.

  • OBLIGATION TO SUPPORT ‌ The parties agree that subsequent to the execution of this Memorandum of Understanding and during the period of time said Memorandum is pending before the Board of Supervisors for action, neither SEIU Local 721, nor Management, nor their authorized representatives, will appear before the Board of Supervisors or meet with members of the Board of Supervisors individually to advocate any amendment, addition or deletion to the terms and conditions of this Memorandum of Understanding. It is further understood that this Article shall not preclude the parties from appearing before the Board of Supervisors nor meeting with individual members of the Board of Supervisors to advocate or urge the adoption and approval of this Memorandum of Understanding in its entirety.

  • Licensors Obligations 4.5.1. Xxxxx the Licensee the right to use the intellectual property (the Service) as in the Agreement. Ensure 24/7 availability of the Service, apart from preventive maintenance time. 4.5.2. Keep confidential any information, materials, documents which become available to the Licensee in the course of performance of this Agreement. 4.5.3. Duly publish the official messages (documents) related to the right to use the Service.

  • Processor’s Obligations Except where expressly permitted by Article 28 (3)(a) GDPR, Processor shall process data subjects’ Data only within the scope of the Agreement and the instructions issued by Controller. Where Processor believes that an instruction would be in breach of applicable law, Processor shall notify Controller of such belief without undue delay. Processor shall be entitled to suspend performance on such instruction until Controller confirms or modifies such instruction. Processor shall, within Processor’s scope of responsibility, organize Processor’s internal organization so it satisfies the specific requirements of data protection. Processor shall implement technical and organizational measures to ensure the adequate protection of Controller’s Data, which measures shall fulfil the requirements of the GDPR and specifically its Article 32. Processor shall implement technical and organizational measures and safeguards that ensure ongoing confidentiality, integrity, availability and resilience of processing systems and services and shall implement a process for regularly testing, assessing and evaluating the effectiveness of technical and organizational measures for ensuring the security of the processing. Controller is familiar with these technical and organizational measures, and it shall be Controller’s responsibility that such measures ensure a level of security appropriate to the risk. The parties agree to refer to the existing certification of Processor by Kiwa International Cert GmbH in accordance with DIN ISO/IEC 27001:2015 which is considered sufficient evidence for these purposes by Controller and which is available on the website of Processor (xxx.xxxxxxx.xxx). Processor reserves the right to modify the measures and safeguards implemented, provided, however, that that the level of security shall not be less protective than initially agreed upon. Processor shall support Controller, insofar as is agreed upon by the parties, and where possible for Processor, in fulfilling data subjects’ requests and claims, as detailed in chapter III of the GDPR and in fulfilling the obligations enumerated in Articles 33 to 36 GDPR. Processor shall ensure that all employees involved in Contract Processing of Controller’s Data and other such persons as may be involved in Contract Processing within Processor’s scope of responsibility shall only do so within the scope of the instructions. Furthermore, Processor shall ensure that any person entitled to process Data on behalf of Controller has undertaken a commitment to confidentiality under terms similar to the confidentiality terms of the Agreement. All such confidentiality obligations shall survive the termination or expiration of such Contract Processing. Processor shall notify Controller without undue delay if Processor becomes aware of any Data breaches within Processor’s scope of responsibility. Processor shall implement the measures necessary for securing Data and for mitigating potential negative consequences for the data subject; the Processor shall coordinate such efforts with Controller without undue delay. Processor shall notify to Controller the point of contact for any issues related to data protection arising out of or in connection with the Agreement. The Exhibit provides for a list of the initially designated persons. Processor shall correct or erase Data if so instructed by Controller and where covered by the scope of the instructions permissible. Where an erasure, consistent with data protection requirements, or a corresponding restriction of processing is impossible, Processor shall, based on Controller’s instructions, and unless agreed upon differently in the Agreement, destroy, in compliance with data protection requirements, all carrier media and other material or return the same to Controller. In specific cases designated by Controller, such Data shall be stored or handed over. The associated cost for doing so and protective measures to put in place shall be agreed upon separately, unless already agreed upon in the Agreement. Processor shall, upon termination of Contract Processing and upon Controller’s instruction, return all Data, carrier media and other materials to Controller or delete the same. Where a data subject asserts any claims against Controller in accordance with Article 82 of the GDPR, Processor shall support Controller in defending against such claims, where possible at Controller’s cost as set out in Section 6 para. 3. Controller shall notify Processor without undue delay, and comprehensively, of any defect or irregularity with regard to provisions on data protection detected by Controller in the results of Processor’s work.

  • OBLIGATION TO SERVE As between the Parties, Competitive Supplier has the sole obligation to obtain sources of supply, whether from generating facilities owned or controlled by its affiliates, through bilateral transactions, or the market, as may be necessary to provide All-Requirements Power Supply for all of the Participating Consumers under the Program. Competitive Supplier, except as explicitly limited by the terms included in Exhibit A, shall be obligated to accept all Participating Consumers, regardless of their location or energy needs, subject to Competitive Supplier’s standard credit policies (to the extent permitted by law), Article 5.5 hereof, Exhibit A hereof and the terms of any approval or other order of the Department with respect to this ESA.

  • SUPPLIER’S OBLIGATIONS 4.2.1 The Supplier shall be responsible for implementing all the necessary resources for the performance of its obligations under the Contract, with the exception of those specifically mentionedin the Contractas beingunder the responsibility of the Purchaser. The Supplier shall haveall of thematerials andtoolsneededfor theperformanceof the Contractandshall allocate qualified staff in sufficient numbers to perform the Contract within the contractual deadline. The Supplier shall ensureappropriatepersonneltraining andqualification andsubmitanyproof relating to such qualification upon Purchaser’s request. Within seven (7) days, at the latest, of the Contract coming into force, the Supplier shall appoint a staff member as aprojectmanager and shall inform the Purchaser accordingly. The project manager shall plan, coordinate and monitor all the Supply’sneedsin compliancewith the Contractandthe Good Industry Practices andshall be the Supplier’s contact person for the Purchaser. 4.2.2 The Supplier shall request from the Purchaser in a timely manner, any approvals and instructions needed for the correct performance of the Contract. If applicable, the Purchaser shall grant access to the site where the Supply is to be performed (the “Site”) and /or make available to the Supplier the materials and/or perform the works identified in the Contract. 4.2.3 The Supplier shall promptly remedy or shall ensure that its subcontractors promptly remedy any defects relating to the Supply noted during the abovementioned visits as well as any defect notified to it by the Purchaser concerning its performance. 4.2.4 The Supplier shall ensure that the Supply provided are fit for the purposes that may reasonablybeinferred from the Contractandinaccordancewith the timetableforperformance defined in the Contract. In any event the Supplier commitshimself toachieveperformance and results stipulated in the Contract. The performance deadlinesmay only be extended or reduced through an amendment to the Contract, in accordance with the provisions of Article 5.1. The Supply shall be delivered in a state of full completion with the complete Documentation associated therewith as well as all instructions, recommendations and other indications necessary in order for them to be used correctly and under the appropriate safety conditions. “Documentation” shall mean any operation and maintenance manuals, drawings, calculations, technical data, logic diagrams, progress reports, quality documentation, conformity certificates, test reports, bill of lading, certificates of origin, export control classification list number as per any applicable export regulation - such as (i) the European Council Regulation 428/2009 (as amended), (ii) the U.S. Export Administration Regulations (“EAR”), (iii) percentage of U.S. origin content, (iv) U.S. Export Control Classification Number (“ECCN”), (v) U.S. Munitions List category (“USML”),(vi) (if applicable) export authorizations and licenses, and/or (vii) Harmonized Tariff Code - and any such other documents required under the Contract and/or applicable laws. The Supplier shall also furnish such programme of design, manufacture and delivery as the Purchaser may reasonably require. If so required by the Purchaser, the Supplier shall submit any such Documentation to the Purchaser with sufficient time for review and approval. Where the Documentation provided by the Supplier is not compliant with Purchaser’s contractual requirements, the Supplier must make the necessary modifications, and indemnify the Purchaser for any costs, liabilities or penalties incurred by the Purchaser due to the delays or non-compliance in Documentation delivered by the Supplier and shall not be entitled to an adjustment of the delivery schedule in case of any revision.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!