We use cookies on our site to analyze traffic, enhance your experience, and provide you with tailored content.

For more information visit our privacy policy.

Fusing Sample Clauses

Fusing. In-line Fused and Non-Fused Holders and ConnectorsCity Streets - In-line fuse holders shall be waterproof Elastimold catalogue #65U or Xxxxxxx HEB-XX Xxxxxx and terminal, KTK 15 amp. Fuse and 2 #1A0512 insulating boots, or approved equal. Limited access roadways – Fuse shall be in line weather proof KTK 15 amp. Service cable shall be secured to service bend in an approved manner.
Sample 1See All (6)
Fusing. The following diagram shows a typical arrangement for the fusing requirements. The diagram is non- exhaustive and is provided for reference only. Figure 1: Fusing arrangements for cable runs of more than 30 metres distance between source fusing and local means of isolation41 42. Check Meter Main Meter Supply URN 15D/095 41 Local isolation may be provided by the use of solid links or fuses and may be placed on either side of the test terminal block. Where fuses are to be used, the additional burden shall be accounted for. 42 Check Meters and other burden may be supplied via an additional secondary winding of the VT. (Loss of Route to Market Notice) To: [●] (the “CfD Counterparty”) [Address] From: [●] (the “Generator”) [Unique reference number: [●]]
Sample 1Sample 2
Fusing. There shall be one in-line (cartridge type) fuse per street light, located within each pole and accessible through the hand hole. Ornamental Lighting The Director may require ornamental lighting, banner arms, basket hangers, and internal irrigation.
Sample 1
Fusing. The following diagram shows a typical arrangement for the fusing requirements. The diagram is non-exhaustive and is provided for reference only. Figure 1: Fusing arrangements for cable runs of more than 30 metres distance between source fusing and local means of isolation41 4243. Check Meter Main Meter Supply URN 15D/095 41 Local isolation may be provided by the use of solid links or fuses and may be placed on either side of the test terminal block. Where fuses are to be used, the additional burden shall be accounted for. 42 Local isolation may be provided by the use of solid links or fuses and may be placed on either side of the test terminal block. Where fuses are to be used, the additional burden shall be accounted forCheck Meters and other burden may be supplied via an additional secondary winding of the VT.
Sample 1
Fusing. September 1, 2006 Distribution Transformers Newfoundland Power Inc. Schedule B – Statement of Work Transformers shall be fused as per CSA DTWG-03.
Sample 1
Fusing. The following diagram shows a typical arrangement for the fusing requirements. The diagram is non-exhaustive and is provided for reference only. Figure 1: Fusing arrangements for cable runs of more than 30 metres distance between source fusing and local means of isolation414244 45. Check Meter Main Meter Supply URN 15D/095 41 Local isolation may be provided by the use of solid links or fuses and may be placed on either side of the test terminal block. Where fuses are to be used, the additional burden shall be accounted for. 42 Check Meters and other burden may be supplied via an additional secondary winding of the VT44 Local isolation may be provided by the use of solid links or fuses and may be placed on either side of the test terminal block. Where fuses are to be used, the additional burden shall be accounted for.
Sample 1

Related to Fusing

  • Decorations The only acceptable form of affixing items to walls is the use of white sticky tack, and must be removed by the Resident prior to move out, or be subject to removal charges. Spikes, hooks, screws, tacks or nails or any permanent adhesion type tape shall not be put into or on the walls or woodwork, ceilings, furnishings, doors or windows of any part of the Residence. Residents may not decorate the outside of their room door unless for special occasions approved by the Manager. Strings of indoor lights should not be in direct contact with any flammable materials and should not be left on while the room is unattended.

  • Recommended language skills The sending institution, following agreement with the receiving institution, is responsible for providing support to its nominated candidates so that they can have the recommended language skills6 at the start of the mobility period (see also section 5 “Preparation and Support”). Student Mobility Staff Mobility CZ BRNO05 Czech English B2 for Czech B2 for English B2 for Czech B2 for English Jerusalem English C1 C1 For more details on the language of instruction recommendations, see the course catalogue of each institution. The links to the course catalogue are provided in the first section.

Most Referenced Clauses

Most Referenced Definitions