Horizontal curves Sample Clauses

Horizontal curves. A minimum sight distance with clear visibility, measured along the centerline, shall be provided of at least three hundred (300’) feet on major streets, 200 feet for collector (and industrial) streets and one hundred (100’) feet on all other streets.
Sample 1
AutoNDA by SimpleDocs
Horizontal curves. A design exception is required if ∆V exceeds 15 mph and there is an accident cluster or trend associated with the design element. Clear Zone: Consider the removal, relocation or shielding of obstacles within the clear zone. The decision to address these issues will depend on the degree of severity of the problem, accident clusters or trends identified by Safety Management cost effectiveness of treatment, the scope and time constraints of the project and available funding. Decisions to not provide an adequate clear zone must be documented in the Scope of Work Report and supported by an approved design exception. Signing: Signing upgrades are mandatory for all rehabilitation projects. Drainage: Drainage issues, such as severe pipe corrosion or erosion that could adversely impact the roadway, that are identified during the preliminary field review or by MDT Maintenance will be considered for treatment. The decision to address these issues will depend on the degree of severity of the problem, cost effectiveness of treatment, the scope and time constraints of the project and available funding. Major Rehabilitation Intent: The intent of these projects is to rehabilitate the existing pavement structure through an engineered approach that considers the observed pavement distress, the in-place material, and roadway geometrics. Milling operations may be > 0.20 ft (60 mm) and may expose base gravel which can then be treated or modified. New right-of-way and utility relocation may be required to improve geometrics, to flatten slopes and enhance safety. Considerations: Eligible Funding: Major Rehabilitation projects will be funded with Federal Aid funds. Environmental Process: Follow the NEPA process. Development time: Appropriate soil survey work, subsurface analysis, traffic data and accident data must be collected. The preliminary surfacing recommendation a 20-year design life will confirm the level of rehabilitation (minor or major). The data collection and engineering required to determine the level of rehabilitation should take six to nine months. Additional development time for a major rehabilitation should be three to four years, given the probable inclusion of other features. Americans With Disabilities Act: Install curb ramps wherever curb, gutter and sidewalk are adjacent to the project. Evaluate existing and potential pedestrian use to determine ramp locations, the need for sidewalk improvements, and the installation of additional sidewalk. Coordinate propo...
Sample 1
Horizontal curves. A. The minimum radius of all curves on Mainline Track shall accommodate all On-track Vehicles.
Sample 1

Related to Horizontal curves

  • Demarcation Point 98.1 CenturyLink will designate the point of demarcation between CenturyLink’s equipment and CLEC’s collocated equipment, which point of demarcation shall be in or adjacent to its Collocation Space unless otherwise mutually agreed to by the Parties. At CLEC's request, CenturyLink will identify the location(s) of other possible demarcation points available to CLEC, and CLEC will designate from these location(s) the point(s) of demarcation between its collocated equipment and CenturyLink's equipment. CenturyLink will use its best efforts to identify the closest demarcation point to CLEC's equipment that is available.

  • Rate Demarcation Point The physical point in a Verizon provided network facility at which Verizon's responsibility for maintaining that network facility ends and the Customer's responsibility for maintaining the remainder of the facility begins, as set forth in this Agreement, Verizon's applicable Tariffs, if any, or as otherwise prescribed under Applicable Law.

  • Horizontal Movement The Board encourages all unit members to improve their skills through advanced training and, as an inducement thereto, provides extra compensation for those who do so successfully. The Board delegates to the Superintendent the responsibility for assuring that unit members comply with the following regulations when claiming credit for advanced studies.

  • Interconnection Point The Service Provider is responsible for connecting to the LFC Network at the Interconnection Point. The LFC may only change an Interconnection Point if a change is necessary to protect the security or integrity of that Interconnection Point in order to maintain the continuity of supply of the Wholesale Services. In the event of any such change:

  • Elevation Elevation is defined as restoring an employee to the higher classification, with permanent status, which was held prior to being granted a demotion or to a class that is between the current class and the class from which the employee was demoted. Upon elevation, an employee’s salary will be determined in the same manner that is provided for promotion in Section 43.5, above.

  • Interconnection Points 8.5.1 The IP of a Party (“Receiving Party”) for Measured Internet Traffic delivered to the Receiving Party by the other Party shall be the same as the IP of the Receiving Party for Reciprocal Compensation Traffic under Section 7.1 above.

  • Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where InterGlobe has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to InterGlobe. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for InterGlobe (e.g. hairpinning):

  • Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.

  • Teaching Loads The range of teaching loads, number of preparations and number of pupil contacts required should provide for effective instruction and meaningful teacher-student interaction. DPS and the Association agree to work together to seek increased state funding to decrease class size. The principal shall report to the CSC, after the roster verification process, the number of students in each class and this will be published in the CSC minutes on the school’s website. For the purposes of this section, a “class” shall be defined as any general education, including electives and model one classes. Upon request, after the roster verification process, the District shall provide the Association with the student information management system data regarding class enrollment.

  • Teaching Load Full teaching assignments shall normally include 12 course credit hours of scheduled teaching per academic quarter. A reassignment of duty, for the equivalent of 3 or 4 credit course, shall be provided during one term of the first academic year to all newly hired tenure track faculty to further their teaching, scholarship and service and to encourage faculty retention. Wherever possible the University will endeavor to arrange teaching schedules that avoid excessive numbers of preparations and recognize evening and/or off-campus assignments. Class sizes will be established and monitored by the appropriate academic xxxx in consultation with division chairs and affected faculty each term. The following equivalencies will be used in determining teaching assignments:

Time is Money Join Law Insider Premium to draft better contracts faster.