Metering Devices for Fuel Sample Clauses

Metering Devices for Fuel. (a) The Fuel delivered by Purchaser in accordance with the terms of this Agreement shall be measured by Xxxxxxx’x metering devices at the Fuel Metering Points. Seller shall use Commercially Reasonable Efforts in accordance with its rights as purchaser under the Xxxxxxx PPA to cause Xxxxxxx to be responsible to own, operate, maintain and control all of Xxxxxxx’x Fuel metering equipment at no expense to Purchaser. (b) The number and general location of Xxxxxxx’x Fuel metering devices shall be as set forth in Appendix B. All of Xxxxxxx’x Fuel metering devices shall be sealed. Seller shall use Commercially Reasonable Efforts in accordance with its rights as purchaser under the Xxxxxxx PPA to cause Xxxxxxx to allow Purchaser’s representatives to be present when the seal is broken for the purpose of inspecting, testing and adjusting such metering devices. (c) This section has been intentionally deleted.
Sample 1
AutoNDA by SimpleDocs
Metering Devices for Fuel. (a) The Fuel delivered by Purchaser in accordance with the terms of this Agreement shall be measured by the Seller's metering devices at the Fuel Metering Points. Seller shall be responsible for, operate, maintain and control all of Seller's Fuel metering equipment at its sole cost and expense. (b) The number, type and general location of Seller's Fuel metering devices shall be as set forth in Appendix B. All of Seller's Fuel metering devices shall be sealed, and the seal shall be broken only when representatives of both Parties are present for the purpose of inspecting, testing and adjusting such metering devices.
Sample 1
Metering Devices for Fuel. (a) The Fuel delivered by Purchaser in accordance with the terms of this Agreement shall be measured by Seller's metering devices at the Fuel Metering Points. Seller shall be responsible for the ownership, operation, maintenance and control of all of Seller's Fuel metering equipment at its sole cost and expense. (b) The number and general location of Seller's Fuel metering devices shall be as set forth in Appendix C. All of Seller's Fuel metering devices shall be sealed, and the seal shall be broken only when representatives of both Parties are present for the purpose of inspecting, testing and adjusting such metering devices.
Sample 1

Related to Metering Devices for Fuel

  • Metering The Interconnection Customer shall be responsible for the Connecting Transmission Owner’s reasonable and necessary cost for the purchase, installation, operation, maintenance, testing, repair, and replacement of metering and data acquisition equipment specified in Attachments 2 and 3 of this Agreement. The Interconnection Customer’s metering (and data acquisition, as required) equipment shall conform to applicable industry rules and Operating Requirements.

  • Calibration The comparison of a measurement system or device of unverified accuracy with a measurement system of known and greater accuracy to detect deviation of the unverified measurement system from required performance specifications (of the unverified measurement system or device) and to quantify all measured values to applicable units of the international system of units.

  • Metering Data At Developer’s expense, the metered data shall be telemetered to one or more locations designated by Connecting Transmission Owner, Developer and NYISO. Such telemetered data shall be used, under normal operating conditions, as the official measurement of the amount of energy delivered from the Large Generating Facility to the Point of Interconnection.

  • Delivery Point The delivery point is the point of delivery of the Power Product to the CAISO Controlled Grid (the “Delivery Point”). Seller shall provide and convey to Buyer the Power Product from the Generating Facility at the Delivery Point. Title to and risk of loss related to the Power Product transfer from Seller to Buyer at the Delivery Point.

  • Metering Equipment 13.01. Utility will furnish, install, own and maintain metering equipment capable of measuring the flow of kilowatt-hours (kWh) of energy. The Customer's service associated with the CRG will be metered at a single metering point. The metering equipment will measure energy delivered by Utility to Customer and also measure energy delivered by Customer to Utility. Customer agrees to provide safe and reasonable access to the premises for installation of this equipment and its future maintenance or removal.

  • Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.

  • Delivery Points ‌ Project water made available to the Agency pursuant to Article 6 shall be delivered to the Agency by the State at the delivery structures established in accordance with Article 10.

  • Packing Materials and Containers for Shipment Packing materials and containers in which the good is packed for shipment shall be disregarded in determining whether-- (i) the non-originating materials used in the production of the good undergo an applicable change in tariff classification set out in subdivision (t) of this note; and (ii) the good satisfies a regional value-content requirement.

  • Interconnection Customer’s Interconnection Facilities The Interconnection Customer shall design, procure, construct, install, own and/or control the Interconnection Customer’s Interconnection Facilities described in Appendix A at its sole expense.

  • Packaging Materials and Containers for Retail Sale 1. When packaging materials and containers in which a good is packaged for retail sales are classified in the Harmonized System with the good, they shall not be taken into account in determining whether all non-originating materials used in the production of the good undergo the applicable change in tariff classification set out in Annex 4.03. 2. When the good is subject to a requirement of regional value content, the value of these packaging materials and containers shall be taken into account as originating or non-originating materials, as the case may be, in calculating the regional value content of the good.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!