Space Measurement Sample Clauses

Space Measurement. The measurement of leased space shall be based on the method of measurement used by the State University System for gross square feet as described in BOG Regulation 17.001.
AutoNDA by SimpleDocs
Space Measurement. The Rentable Areas of the Leased Premises and the Building shall be as set forth in the Basic Lease Provisions. Landlord and Tenant have used (and shall use for purposes of any future determination) the American National Standard Method for Xxxxxxxxx Xxxxx Xxxx xx Xxxxxx Xxxxxxxx, XXXXX000.0-0000, as promulgated by the Building Owners and Managers Association ("BOMA") in determining the precise "Rentable Area" of the Leased Premises and the Building for all purposes of this Lease. In the event of any change in the Rentable Areas set forth in the Basic Lease Provisions by reason of expansion or contraction of the Leased Premises or the Building, Landlord shall certify such change to Tenant within thirty (30) days after such change becomes effective for purposes of this Lease. Tenant shall have ninety (90) days from its receipt of such certification to contest Landlord's calculation in a reasonable manner and fashion. Absent such contest being initiated in a timely manner, such certification shall be deemed correct for all proposes hereunder in the absence of manifest error. Upon final determination of the revised Rentable Area(s) Landlord and Tenant shall execute a supplement to this Lease setting forth the applicable Rentable Areas.
Space Measurement. The RSF of the Premises is as set forth in Section 1.1 of the Lease and is not subject to re-measurement. The rentable square footage of the Premises has been determined in accordance with a modified form of the American National Standards Institute/Building Owners and Managers Association International (“ANSI/BOMA”) Form Z65.1-2010. Landlord may re-measure the Building from time to time and, upon Notice to Tenant Landlord’s new measurements shall be binding hereunder provided Landlord measures according to the same modified ANSI/BOMA standard or a more current modified ANSI/BOMA standard and further provided any such re-measurement shall not result in an increase in Base Rent or Additional Rent then set forth in this Lease for the balance of the then Term. As of the Lease Date, Xxxxxx’s Share for Taxes and Operating Expenses is ratio of the RSF of the Premises divided by the 1,193,458, the RSF of the Building excluding any storage areas and roof top areas. For so long as the Project shall contain non-office uses, Landlord shall have the right (but not the obligation) to determine in accordance with sound accounting and management principles, Xxxxxx’s Share of Operating Expenses and Taxes for only the office portion of the Building and Amenities, in which event, Xxxxxx’s Share shall be based on the ratio of the rentable square footage of the Premises to the rentable square footage of the such office portion of the Building and the Amenities. Tenant’s Share shall change when space is added to or deleted from the Premises, additional floors or other additions are added to the Building and if Landlord ceases to own a portion of the Building after a subdivision or vertical separation and Landlord no longer has responsibility for the Operating Expenses and Taxes for the portion not owned by Landlord.
Space Measurement. The Premises leased by Tenant hereunder from time to time (including, without limitation, as of the Commencement Date and the Expansion Premises Commencement Date, and any Additional Space, to the extent applicable) and the Buildings within which any such Premises’ are located from time to time shall be measured in accordance with the Building Owners and Managers Association (BOMA) standard method of floor measurement (ANSI/BOMA 265.1-1996) for single and multi-tenanted buildings to define all building and floor measurements on both a rentable and useable basis.
Space Measurement. The calculation of all rentable and usable square feet and conversion factors shall be the same and consistent with the Building Owner and Refusal Space. If the prospective tenant desires to lease additional space covered by the statement in addition to the Right of First Refusal Space, Tenant must lease all space on such floor that the prospective tenant desires to lease if Tenant elects to lease the applicable Right of First Refusal Space.

Related to Space Measurement

  • Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Performance Measurement The Uniform Guidance requires completion of OMB-approved standard information collection forms (the PPR). The form focuses on outcomes, as related to the Federal Award Performance Goals that awarding Federal agencies are required to detail in the Awards.

  • Temperature Measurement Temperature will be measured by the nearest automatic Melbourne Bureau of Meteorology Monitoring Station for example (but not limited to): Melbourne, Moorabbin, Dunns Hill, Melbourne Airport, Frankston, and Point Xxxxxx. At the commencement of each project, the onsite management and employee representatives shall agree which is to be the applicable automatic weather monitoring station.

  • Performance Measure Grantee will adhere to the performance measures requirements documented in

  • Performance Measures The System Agency will monitor the Grantee’s performance of the requirements in Attachment A and compliance with the Contract’s terms and conditions.

  • Measurement Should the State terminate this contract as herein provided, no fees other than fees due and payable at the time of termination shall thereafter be paid to the Engineer. In determining the value of the work performed by the Engineer prior to termination, the State shall be the sole judge. Compensation for work at termination will be based on a percentage of the work completed at that time. Should the State terminate this contract under paragraph (4) or (5) above, the Engineer shall not incur costs during the thirty-day notice period in excess of the amount incurred during the preceding thirty days.

  • Corrective Measures If the Participating Generator fails to meet or maintain the requirements set forth in this Agreement and/or the CAISO Tariff, the CAISO shall be permitted to take any of the measures, contained or referenced in the CAISO Tariff, which the CAISO deems to be necessary to correct the situation.

  • Measuring EPP parameters Every 5 minutes, EPP probes will select one “IP address” of the EPP servers of the TLD being monitored and make an “EPP test”; every time they should alternate between the 3 different types of commands and between the commands inside each category. If an “EPP test” result is undefined/unanswered, the EPP service will be considered as unavailable from that probe until it is time to make a new test.

  • Ongoing Performance Measures The Department intends to use performance-reporting tools in order to measure the performance of Contractor(s). These tools will include the Contractor Performance Survey (Exhibit H), to be completed by Customers on a quarterly basis. Such measures will allow the Department to better track Vendor performance through the term of the Contract(s) and ensure that Contractor(s) consistently provide quality services to the State and its Customers. The Department reserves the right to modify the Contractor Performance Survey document and introduce additional performance-reporting tools as they are developed, including online tools (e.g. tools within MFMP or on the Department's website).

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!