Classification Definitions Note: The following classification definitions should be read in conjunction with: • the stream and field definitions in subclause 1.4.3 and 1.4.75 respectively: • the definitions of “or equivalent”, “work within the scope of this level” and “Engineering Associate” at the end of this Schedule; • the National Metal and Engineering Competency Standards Implementation Guide especially Table 2 of that Guide which shows the alignment between old and new titles under the Australian Qualifications Framework. For example Advanced Certificates are now known as National Diplomas and Associate Diplomas as National Advanced Diplomas; • Clause 5.1.3 (f) Points. Trainer/Supervisor/Coordinator - Level 1 A Trainer/Supervisor/Coordinator - Level I is an employee who is responsible for the work of other employees and/or provision of structured on-the-job training. Such an employee has completed a qualification at AQFIII level or above, of which at least one third of the competencies are related to supervision/training, or equivalent. Notwithstanding the above definition an employee who is mainly engaged to perform work supervising or coordinating the work of other employees and who has sufficient additional training beyond that of those coordinated or supervised so as to enable the employee to perform work within the scope of this level shall be classified at this level. Trainer/Supervisor/Coordinator - Level II A Trainer/Supervisor/Coordinator - Level II is an employee who is responsible for the supervision and/or training of Trainers/Supervisors/Coordinators - Level I. Such an employee has completed an AQF IV or V qualification or equivalent of which at least 50% of the competencies are in supervision/training. WAGE GROUP: C14 Engineering/Production Employee - Level I As Engineering/Production Employee - Level I is an employee who is undertaking up to 38 hours induction training which may include information on the enterprise, conditions of employment, introduction to supervisors and fellow workers, training and career path opportunities, plant layout, work and documentation procedures, occupational health and safety, equal employment opportunity and quality control/assurance. An employee at this level performs routine duties essentially of a manual nature and to the level of his/her training:
General Conditions; Definitions 1.01. The General Conditions (as defined in the Appendix to this Agreement) constitute an integral part of this Agreement.
APPLICABILITY OF OTHER RATES, TERMS AND CONDITIONS 12.1 Every interconnection, service and network element provided hereunder, shall be subject to all rates, terms and conditions contained in this Agreement which are legitimately related to such interconnection, service or network element. Without limiting the general applicability of the foregoing, the following terms and conditions of the General Terms and Conditions are specifically agreed by the Parties to be legitimately related to, and to be applicable to, each interconnection, service and network element provided hereunder: definitions, interpretation, construction and severability; notice of changes; general responsibilities of the Parties; effective date, term and termination; fraud; deposits; billing and payment of charges; non-payment and procedures for disconnection; dispute resolution; audits; disclaimer of representations and warranties; limitation of liability; indemnification; remedies; intellectual property; publicity and use of trademarks or service marks; no license; confidentiality; intervening law; governing law; regulatory approval; changes in End User local exchange service provider selection; compliance and certification; law enforcement; no third party beneficiaries; disclaimer of agency; relationship of the Parties/independent contractor; subcontracting; assignment; responsibility for environmental contamination; force majeure; taxes; non-waiver; network maintenance and management; signaling; transmission of traffic to third parties; customer inquiries; expenses; conflicts of interest; survival; scope of agreement; amendments and modifications; and entire agreement.
GEOGRAPHIC AREA AND SECTOR SPECIFIC ALLOWANCES, CONDITIONS AND EXCEPTIONS The following allowances and conditions shall apply where relevant: Where the company does work which falls under the following headings, the company agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.
DATA USED FOR CALCULATIONS The calculations for payments under this Agreement shall be initially based upon the valuations that are placed upon all taxable property in the District, including the Applicant’s Qualified Property, by the Appraisal District in its annual certified tax roll submitted to the District for each Tax Year pursuant to TEXAS TAX CODE § 26.01 on or about July 25 of each year of this Agreement. Immediately upon receipt of the valuation information by the District, the District shall submit the valuation information to the Third Party selected and appointed under Section 4.3. The certified tax roll data shall form the basis of the calculation of any and all amounts due under this Agreement. All other data utilized by the Third Party to make the calculations contemplated by this Agreement shall be based upon the best available current estimates. The data utilized by the Third Party shall be adjusted from time to time by the Third Party to reflect actual amounts, subsequent adjustments by the Appraisal District to the District’s certified tax roll or any other changes in student counts, tax collections, or other data.
Standard Conditions; Definitions 1.01. The Standard Conditions for Grants Made by the World Bank Out of Various Funds, dated July 1, 2008 (“Standard Conditions”), constitute an integral part of this Agreement.
Definitions and Usage Except as otherwise specified herein or as the context may otherwise require, capitalized terms used but not otherwise defined herein are defined in Appendix A hereto, which also contains rules as to usage that shall be applicable herein.
020 Definitions The following definitions shall be applicable to this chapter:
DEFINITIONS AND INTERPRETATION Definitions 1.1 In this Contract, unless the contrary intention appears: Activity End Date means the date reported as such in a Student Statistical Report for an individual's enrolment in an individual subject. Activity Start Date means the date reported as such in a Student Statistical Report for an individual's enrolment in an individual subject. Apprentice has the meaning given to it in the Act. Approved Training Scheme means a training scheme approved under section 5.5.2 of the Act. Brokering Services means the recruitment of individuals to participate in Skills First subsidised training in exchange for payment from the Training Provider or the student. It excludes activities carried out by individuals who are employees of the Training Provider on the Training Provider’s payroll, whose role includes the identification and recruitment of potential students. Business Day means a day which is not a Saturday, Sunday or a public holiday in Melbourne, Victoria.
ECR Number Environmental Commitment Record Requirements Description of ADOT Responsibilities TMP-3 The following measures will be implemented for the Selected Alternative: • All equipment exhaust systems will be in good working order. Properly designed engine enclosures and intake silencers will be used. • Equipment will be maintained on a regular basis. New equipment will be subject to new product emission standards. • Stationary equipment will be located as far away from sensitive receivers as possible. • Construction-related noise generators will be shielded from noise receivers (e.g., use temporary enclosures to shield generators or crushers, take advantage of site conditions to provide topographic separation). • Construction alerts will be distributed to keep the public informed of construction activities, and a toll-free number for construction-related complaints will be provided. • During the design phase, hours of operation will be evaluated to minimize disruptions during construction. ADOT to oversee for compliance TMP-4 Congestion from construction-related traffic will create temporary impacts in the project vicinity. The magnitude of these impacts will vary depending on the location of the sources of the fill material and of the disposition sites for surplus material, the land uses along the routes, the duration of hauling operations, staging locations, and the construction phasing. To identify acceptable routes and times of operation, ADOT, or its representative, will prepare an agreement with local agencies regarding hauling of construction materials on public streets. ADOT to oversee for compliance TP Attachment 000-0 Xxxxx Xxxxxxxx Xxxxxxx Project Record of Decision (ROD) Developer’s Environmental Commitment Requirements The following table includes the Project-specific environmental commitments as written in the ROD, with minor modifications for clarification purposes. As it relates to these Technical Provisions, references to freeway, project, South Mountain Freeway, proposed action, proposed freeway, and Selected Alternative mean the Project, and references to contractor mean Developer. Developer shall comply with and perform all of the contractor and ADOT requirements, including the ADOT obligations, commitments, and responsibilities, identified in the following table, except to the extent of those requirements that are specifically identified in the third column, entitled “Description of ADOT Responsibilities,” which are not delegated to Developer.
