Surface Cleaning. Once in 15 days and as & when • All glasses at entrance doors and windows of the required / as directed. premises would be cleaned using damp and dry method. • Glass table tops, cabin doors, cabin partitions and glass accessories would also be cleaned. • Removal of grease marks or fingerprints on glass counters and partitions. This cleaning is done using approved all-purpose cleaner and lint free cloth or paper towels.
Surface Cleaning. Any areas modified by chipping or hammering shall be cleaned with high pressure water at 7,500 psi minimum to remove any bond-breaking residue, loose concrete, and any deleterious material. This material shall be collected and disposed of by the contractor. Any areas of the prepared surface contaminated by oil or other materials detrimental to good bond as a result of the contractor’s operations shall be cleaned at the contractor’s expense. Removal of concrete debris shall be accomplished either by hand or mechanical means capable of removing wet debris and water in the same pass and after the hydro-demolition process to prevent debris from setting or adhering to the surface of the sound concrete. All concrete debris shall become the property of the Contractor and shall be legally disposed of at the contractor’s expense. The contractor shall be responsible for disposing of all debris generated by the scarification and hydro-demolition operations. Any debris which is allowed to set or adhere to the surface of the sound concrete shall be carefully removed at no additional cost. Exercise care to avoid any damage to the remaining sound concrete or exposed reinforcement
Surface Cleaning. All surfaces subject to spills and/or routine cleaning shall be compatible with disinfectant solutions that may contain up to 10% bleach.
Surface Cleaning. Clean the area to be repaired by abrasive blasting, high-pressure water blasting, or other approved methods. Remove all loose particles, dirt, deteriorated concrete, or other substances that would impair the bond of the repair material. Clean exposed reinforcing steel of concrete, rust, oil, and other contaminants. Follow this with a high-pressure air blast for final cleaning.
Surface Cleaning. Contractor is required to wash the interior of ALL TANKS (NO PRESSURE WASHING). Each tank is required to be inspected and cleaned at each service interval. No Deep Cleaning, No Hydro Jetting, No Lift Station Cleaning.
Surface Cleaning. PEM-6666-0 TECHNICAL SPECIFICATION FOR RATE CONTRACT OF CHAIN PULLEY BLOCKS SPECIFICATION NO. PE-TS-RC-563-A101 SECTION -I PEM-6666-0 TECHNICAL SPECIFICATION FOR RATE CONTRACT OF CHAIN PULLEY BLOCKS SPECIFICATION NO. PE-TS-RC-563-A101 SECTION I PEM-6666-0 Sl. No. BHEL XXX.XX DRAWING TITLE REMARKS SUBMISSION SCHEDULE ‐ WEEK NUMBER FROM DATE OF P.O 1 PE‐V0‐RC‐563‐A101 "GA Drawing for Chain Pulley Block with detail BOM with painting details For Customer's approval 2 2 PE‐V0‐RC‐563‐A102 Manufacturing Quality Plan For Customer's approval 2 3 PE‐V0‐RC‐563‐A104 Erection procedure For BHEL's approval 4 4 PE‐V0‐RC‐563‐A103 O & M Manual For BHEL's approval 4 5 PE‐V0‐RC‐563‐A106 Mandatory spare parts list (if applicable) For Customer's approval 3
Surface Cleaning. Surficial cleaning of non-porous or semi-porous surfaces showing visible mold-growth will be conducted using a detergent solution. Surfaces to be treated will be cleaned and an anti-microbial coating (Xxxxxx 40-20 or equivalent) applied to the surface. The anti-microbial coating will be applied following sufficient dry time for the detergent solution. Wood baseboards and wall studs showing visible mold-growth will be cleaned by washing with a detergent solution and applying an anti-microbial coating. Stained areas may be lightly sanded prior to the application of the anti-microbial coating.
Surface Cleaning. The metal surfaces shall be cleaned by one or more of the nine surface methods listed below to obtain a white metal surface or minimum requirements of paint Contractor. The following list of visual standards for cleaning steel structures is as established by the Steel Structures Painting Council.
Surface Cleaning. Polish all bright metal work using an approved metal cleaner/polish.
