Verification and Check Systems Sample Clauses

Verification and Check Systems. Austria Specifications for thermal quality, fire protection and acoustic requirements of insulation materials are regulated by European (CEN) and Austrian (ÖNORM) standards. Calculation of the energy demand and bench marks for the energy consumption are regulated by OIB-Richtline 6 (Directive of the Austrian Institute of Construction Engineering), following the requirements of the EPBD. There is one calculation method for all Austrian provinces. Calculation can be done by approved software tools (Archiphysik, Ecotech, GEQ….). Spain When dealing with insulating materials thermal characterization is required according to standard laboratory procedures such as ISO-8302 and ISO-8990. For the calculation of thermal transmittance of constructive elements, the methodology described in ISO-6946 is applied. In addition, Spanish normative is supported by an specific software (LIDER) for the calculation of the energy demand of the buildings (including thermal transmittance, infiltrations, shadings, etc.). Hungary For the classification of insulation materials and the calculation of the thermal transmittance European standards apply. The requirements on the thermal transmittance of building elements are set in the Hungarian decree TNM 7/2006, based on the EPBD. The calculations can be carried out with various software tools, etc. WinWatt or Archiphysik. European standards apply (e.g. ISO-8302 and ISO-8990, ISO-6946). Greece No verification systems apply for the classification of insulation materials and the calculation of their thermal transmittance. Denmark It is difficult to actually control the U-value of constructions in practice. In the Danish building regulations and in guidelines from the Danish Building Research laboratory (SBi) there is shown how to obtain a good insulation quality and linelosses are indicated. The influence of this can be analysed in calculation programmes like Be06 (introducing EU-EPBD demands). Thermofotyography is often used to control possible cold bridges.
AutoNDA by SimpleDocs
Verification and Check Systems. Austria The Styrian housing subsidy for new built multi-storey buildings requires the same values for air change rates as ÖNORM 8110-5. Measurements have to be done by a Blower Door test according ÖNORM EN 13829. For new buildings up to 10 living units every third flat, from 10 living units on every fifth flat has to be measured. Spain Air tightness analysis is carried out according to ISO-9972, EN-12207 and EN- 1026 standards. Hungary European standards apply (e.g. ISO-9972, EN-12207, EN-1026) Greece European standards apply (EN 13829) Denmark European standards is used here. Using blowerdoor tests at +/- 50 Pa and leak detection by smoke test.
Verification and Check Systems. Denmark The quality is not checked normally except noise monitoring which is a requirement. Monitoring of electricity use and HRV efficiency can be close by installing an extra electricity meter and a sensor in the inlet air. Greece No verification and check system apply for heat recovery ventilation.

Related to Verification and Check Systems

  • Verification of Use 20 a. Pursuant to Multnomah County policy, Management must 21 require the completion of a certification form by the employee’s health care provider 22 and any other verifications required for under the provisions of the FMLA, OFLA, or 23 their successors.

  • Verification Bank may, from time to time, verify directly with the respective Account Debtors the validity, amount and other matters relating to the Accounts, either in the name of Borrower or Bank or such other name as Bank may choose.

  • Search, Enquiry, Investigation, Examination And Verification a. The Property is sold on an “as is where is basis” subject to all the necessary inspection, search (including but not limited to the status of title), enquiry (including but not limited to the terms of consent to transfer and/or assignment and outstanding charges), investigation, examination and verification of which the Purchaser is already advised to conduct prior to the auction and which the Purchaser warrants to the Assignee has been conducted by the Purchaser’s independent legal advisors at the time of execution of the Memorandum.

  • Medical Verification The Town may require medical verification of an employee’s absence if the Town perceives the employee is abusing sick leave or has used an excessive amount of sick leave. The Town may require medical verification of an employee’s absence to verify that the employee is able to return to work with or without restrictions.

  • MEASUREMENT AND VERIFICATION The goal of this task is to report the benefits resulting from this project. Project team may use in- house expertise of the project demonstration site or use third party vendor for measurement and verification (M&V) of GHG and energy consumption reduction. The Recipient shall: • Enter into agreement with M&V subcontractor per Task 1.9 (if using outside vendor) • Coordinate site visits with the M&V subcontractor at the demonstration site(s) • Develop M&V protocol for pre-installation measurement (and calculations) following Section II.B.2 of the grant solicitation manual3: o Electric, natural gas and/or other fossil fuel consumption and greenhouse gas emissions (use appropriate emissions factor from Attachment 8 of the grant solicitation) of the equipment/process/system(s)/sub-system(s) that are be upgraded and/or replaced and/or modified; and o If necessary, ensure installation of sub-metering equipment and data loggers for pre/post data analysis. • Prepare and provide a detailed M&V Plan for each project demonstration site to include but not be limited to: o A description of the monitoring equipment and instrumentation which will be used; o A description of the key input parameters and output metrics which will be measured; o A description of the M&V protocol and analysis methods to be employed; and o A description of the independent, third-party measurement and verification services to be employed, if applicable. • Perform three months (or shorter period as approved in writing by the CAM) of pre- installation measurements (and calculations) based on the M&V protocol for pre- installation. • Prepare and provide a Pre-Installation M&V Findings Report that includes M&V protocol, pre-install measurements (and calculations), analysis, and results performed in this task. • Develop M&V protocol for post-installation measurements (and calculations) of: o Electric, natural gas and/or other fossil fuel consumption and greenhouse gas emissions (use appropriate emissions factor from Attachment 8 of the grant solicitation) of the equipment/process/system(s)/sub-system(s) that will be upgraded and/or replaced and/or modified.  Perform 12 months (or shorter period as approved in writing by the CAM) of post- installation measurements based on M&V protocol for post-installation. • Provide a summary of post-installation M&V progress in Progress Report(s) (see subtask 1.5) which shall include but not be limited to: o A narrative on operational highlights from the reporting period, including any stoppages in operation and why; and o A summary of M&V findings from the reporting period. • Analyze post-installation electrical, natural gas and/or other fossil fuel consumption and GHG emissions. 3 GFO-18-903, Food Production Investment Program, California Energy Commission, November 2018. xxxxx://xxx.xxxxxx.xx.xxx/contracts/GFO-18-903/000_FPIP_Solicitation_Manual.docx • Prepare and provide a Post-installation M&V Findings Report that includes M&V protocol, pre and post install measurements (and calculations), analysis, and results performed in this task. Results should at a minimum report on the reduction of electricity, natural gas and/or other fossil fuel usage and reductions of GHG emissions that directly result from this project.

  • Account Verification Whether or not a Default or Event of Default exists, Agent shall have the right at any time, in the name of Agent, any designee of Agent or any Borrower, to verify the validity, amount or any other matter relating to any Accounts of Borrowers by mail, telephone or otherwise. Borrowers shall cooperate fully with Agent in an effort to facilitate and promptly conclude any such verification process.

  • Verification Procedure (1) The signature file of each processed file is validated.

  • E-Verification If applicable, Contractor represents and warrants that it will ensure its compliance with the Mississippi Employment Protection Act of 2008, and will register and participate in the status verification system for all newly hired employees. Mississippi Code Annotated §§ 71-11-1 et seq. The term “employee” as used herein means any person that is hired to perform work within the State of Mississippi. As used herein, “status verification system” means the Illegal Immigration Reform and Immigration Responsibility Act of 1996 that is operated by the United States Department of Homeland Security, also known as the E-Verify Program, or any other successor electronic verification system replacing the E-Verify Program. Contractor agrees to maintain records of such compliance. Upon request of the State and after approval of the Social Security Administration or Department of Homeland Security when required, Contractor agrees to provide a copy of each such verification. Contractor further represents and warrants that any person assigned to perform services hereafter meets the employment eligibility requirements of all immigration laws. The breach of this agreement may subject Contractor to the following:

  • Verifications If Partner acquires Red Hat Products and/or Services directly from Red Hat, during the Term and for at least two (2) years thereafter, Partner will keep and maintain commercially reasonable written records regarding Partner’s use and distribution of the Red Hat Products and Services and business activities related to the Program(s) ("Records"). Red Hat may, at its own expense, verify the Records to determine Partner’s compliance with this Agreement. This verification may take the form of requests for information, documents or records (to which Partner will respond promptly), on-site visits (for which Partner shall grant Red Hat the requisite access), or both. The Parties will act reasonably and cooperate with each other in respect of such verifications. Any on-site visit will occur during regular business hours and will not interfere unreasonably with Partner’s business. For an on-site visit, Red Hat will give Partner at least thirty (30) day’s prior written notice.

  • COLLECTION AND PROCESSING OF ITEMS In processing items You have deposited for collection, We are only Your agent and assume no responsibility beyond the exercise of ordinary care. Any item deposited is subject to final settlement in cash or credit. We may use any method We feel is appropriate to collect items, which may include use of a Federal Reserve Bank. We are not responsible for the acts of any third party We use for the collection of items including responsibility for lost items. If We use a local clearinghouse in the collection of items, You authorize Us to do so and to act in accordance with any applicable rules and regulations. We may permit You to withdraw funds from Your Account before final settlement has been made, however, if final settlement is not made, We have the right to charge Your Account or otherwise require You to repay such funds. In processing items presented for payment on Your Account, We will pay such items each business day in an order of Our choosing, all of which means that the transactions may not be processed in the order in which they occurred and that You could incur multiple fees in a single day should there be insufficient funds to pay all items presented that day.

Time is Money Join Law Insider Premium to draft better contracts faster.