We use cookies on our site to analyze traffic, enhance your experience, and provide you with tailored content.

For more information visit our privacy policy.

Electrical Specifications Sample Clauses

Electrical Specifications. 12.1 Electricity supply will be provided as per terms and conditions indicated in Annexure - 2.The Licensee shall bear the amount of all the bills/costs for the electricity that may be consumed due to the operation of the advertisement panels /spaces allotted under this agreement. Licensee shall use energy efficient equipment. Advertiser shall follow the I.E. Rules, Acts for safety of equipment, public & Staff. 12.2 Rate of electricity chargeable from Licensee shall be at the rate at which Electricity Company / Distribution Company /Agency would levy on such a customer, had he obtained supply directly from Electricity Company / Distribution Company /Agency. DERC policy and Electricity Act (as amended from time to time) shall be applicable.
Electrical Specifications. 12.1 Electricity supply will be provided as per terms and conditions indicated in Annexure -
Electrical Specifications. (a) Lighting: 2’x4’ recessed fluorescent lay-in 3” deep, 18 cell low iridescence Parabolic louver (1 fixture per 80SF), Energy efficient ballast. (b) The average electric load of the Premises shall not exceed sib (6) xxxxx per usable square foot for power and three (3) xxxxx per square foot for lighting.
Electrical Specifications. All electrical work shall be installed in accordance with the National Electrical Code, and the local building code. A "
Electrical Specifications. 8.1.1. Electricity supply will be provided as per terms and conditions indicated in Annexure - 3 : Rules and Guidelines for Release of Electric Power. The Licensee shall bear the amount of all the bills/costs for the electricity that may be consumed due to the operation of the advertisement panels /spaces allotted under this agreement. Licensee shall use energy efficient equipment. Advertiser shall follow the I.E. Rules, Acts for safety of equipment, public & Staff. 8.1.2. Rate of electricity chargeable from Licensee shall be at the rate at which Electricity Company / Distribution Company /Agency would levy on such a customer, had he obtained supply directly from Electricity Company / Distribution Company /Agency, MSEB policy and Electricity Act (as amended from time to time) shall be applicable.
Electrical SpecificationsRated voltage 12 VDC Rated current 900mA, 1035mA, max. Rated power consumption 10.8W, 12.42W, max. Operating voltage range 10.2~13.2 VDC Starting voltage 10.2 VDC (25 degC) Operating temperature -40~70 degC Rated speed 25000 RPM+/-10% at rated voltage Air flow 31.3CFM, 27.6 CFM min. Static pressure 2.81 Inch-H2O, 1.96 Inch-H2O min. Acoustic noise 62.0 dB(A), 69.5 dB(A) max.
Electrical Specifications. The detailed electrical specifications of Neg48DC/DC PSU are shown as below : Input Voltage Range -36 ~ -75VDC Inrush Current 75A max. Output Voltage (Volts) +12V Output Current (Amps) 33.3A(+12V) Max Power (Watt) –40°C to 55°C 450W, –40°C to 65°C 400W Output Voltage (Volts) +5VSB Output Current (Amps) 3A (+5VSB) Efficiency >88% @20% load, >91 @50% load, >89% @100% load Ripple P-P (mV) (max.) +12V:120, +5VSB:50 Total Regulation ±5% Hold-up Time (min.) 3mS@-48VDC Over Voltage Protection Latch off Over Current & Short Circuit Protection Auto Recovery Over Temperature Protection Auto Recovery FAN Failure Protection Hot Swap Load Sharing Hi-pot 2545VDC Operating Temperature Range –40°C to 65°C Storage Temperature Range –40°C to +70°C Humidity, Non-Condensing 0 to 95% RH EMI Meets FCC/CISPR 22 Class A(under 6dB) Specification
Electrical Specifications. 8.1.1. Electricity supply will be provided as per terms and conditions indicated in Annexure - 3:
Electrical Specifications. (a) Lighting - Provide 2' x 4' LED - high efficiency light fixtures. (b) Power - Wall mounted duplex receptacles must meet all applicable codes. (c) The average electric load of the Demised Premises shall not exceed five (5) wxxxx per square foot for lighting and power in office areas. Landlord will provide available service of 200A 277/480V, 3 phase, for Tenant's exclusive use. All other switchgear required is a function of the Workletter allowance. (re-use existing) (d) Landlord shall initially provide and install lamps and ballasts. Replacement of same shall be by Landlord, at Tenant's expense.
Electrical Specifications. All electrical work shall be installed in accordance with the National Electrical Code, and the local building code. A "Certificate of Compliance shall be obtained from the New York Board of Fire Underwriters at the completion of the project. Lighting throughout the entire finished office area shall be obtained by the use of recessed 2'0" by 4'0" fluorescent fixtures with parabolic lenses, not to exceed one (l) fixture for each eighty (80) square feet of usable space. Local wall switches shall be provided for control of lighting. Toilet, corridor, lobby and other similar areas shall be lit to 50 foot candles. Exit light lighting for all paths of egress shall be provided in accordance with local building department regulations, if required. All branch circuit wiring shall be above hung ceiling or within dry-wall construction in finished areas and shall be type BX. All exposed conduits in non-finished areas shall be thin-walled "EMT". Wall mounted duplex convenience outlets shall be provided on the basis of one duplex outlet for each 120 square feet of rentable area. This formula shall be used to establish the quantity of outlets. However, the exact location of each outlet shall be coordinated with the Tenant's furniture layout. All duplex outlets are to be considered as normal convenience outlets and shall be wired up with an average of 5 to 8 outlets on one 20 ampere, 120 volt circuit. Panel capacity shall be adequate to handle all tenant lighting and equipment load, providing such equipment load does not exceed 2 xxxxx per square foot of usable area. No credits given for installation less than standard installation.