New Job Classifications When a new classification (which is covered by the terms of this collective agreement) is established by the Hospital, the Hospital shall determine the rate of pay for such new classification and notify the local Union of the same. If the local Union challenges the rate, it shall have the right to request a meeting with the Hospital to endeavour to negotiate a mutually satisfactory rate. Such request will be made within ten (10) days after the receipt of notice from the Hospital of such new occupational classification and rate. Any change mutually agreed to resulting from such meeting shall be retroactive to the date that notice of the new rate was given by the Hospital. If the parties are unable to agree, the dispute concerning the new rate may be submitted to arbitration as provided in the agreement within fifteen (15) days of such meeting. The decision of the arbitrator (or board of arbitration as the case may be) shall be based on the relationship established by comparison with the rates for other classifications in the bargaining unit having regard to the requirements of such classification. When the Hospital makes a substantial change in the job content of an existing classification which in reality causes such classification to become a new classification, the Hospital agrees to meet with the Union if requested to permit the Union to make representation with respect to the appropriate rate of pay. If the matter is not resolved following the meeting with the Union, the matter may be referred to arbitration as provided in the agreement within fifteen (15) days of such meeting. The decision of the arbitrator (or board of arbitration as the case may be) shall be based on the relationship established by comparison with the rates for other classifications in the bargaining unit having regard to the requirements of such classifications. The parties further agree that any change mutually agreed to or awarded as a result of arbitration shall be retroactive only to the date that the Union raised the issue with the Hospital. The parties further agree that the above process as provided herein shall constitute the process for Pay Equity Maintenance as required by the Pay Equity Act.
JOB CLASSIFICATIONS 32.01 Employees holding positions which fall within the Bargaining Unit shall be provided with a job description upon written or email request. 32.02 New job classifications properly included in this Collective Agreement may be established by the Employer during the term of the Collective Agreement. Basic hourly rates of pay for such new job classifications shall be negotiated with the Union. If negotiations fail to produce an agreement within sixty (60) calendar days of the date of written notice from the Employer to the Union regarding the new job classification, then the basic hourly rates of pay may be settled through arbitration in accordance with clause 14.04(d).
Specifications and Standards a) All articles supplied shall strictly conform to the specifications, trademark laid down in the bidding document and wherever articles have been required according to ISI/ ISO/ other applicable specifications/ certifications/ standards, those articles should conform strictly to those specifications/ certifications/ standards. The supply shall be of best quality and description. The decision of the competent authority/ purchase committee whether the articles supplied conforms to the specifications shall be final and binding on the supplier/ selected bidder.
General specifications For the purpose of this Regulation, the vehicle shall fulfil the following requirements:
Changes to Specifications All Specifications and any changes thereto agreed to by the parties from time to time shall be in writing, dated and signed by the parties. Any change to the Process shall be deemed a Specification change. No change in the Specifications shall be implemented by Catalent, whether requested by Client or requested or required by any Regulatory Authority, until the parties have agreed in writing to such change, the implementation date of such change, and any increase or decrease in costs, expenses or fees associated with such change (including any change to Unit Pricing). Catalent shall respond promptly to any request made by Client for a change in the Specifications, and both parties shall use commercially reasonable, good faith efforts to agree to the terms of such change in a timely manner. As soon as possible after a request is made for any change in Specifications, Catalent shall notify Client of the costs associated with such change and shall provide such supporting documentation as Client may reasonably require. Client shall pay all costs associated with such agreed upon changes. If there is a conflict between the terms of this Agreement and the terms of the Specifications, this Agreement shall control. Catalent reserves the right to postpone effecting changes to the Specifications until such time as the parties agree to and execute the required written amendment.
Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.
DAF Specifications Developer shall submit initial specifications for the DAF, including System Protection Facilities, to Connecting Transmission Owner and NYISO at least one hundred eighty (180) Calendar Days prior to the Initial Synchronization Date; and final specifications for review and comment at least ninety (90) Calendar Days prior to the Initial Synchronization Date. Connecting Transmission Owner and NYISO shall review such specifications to ensure that the DAF are compatible with the technical specifications, operational control, and safety requirements of the Connecting Transmission Owner and NYISO and comment on such specifications within thirty (30) Calendar Days of Developer’s submission. All specifications provided hereunder shall be deemed to be Confidential Information.
New Classifications If a new classification is created within the bargaining unit, the Employer agrees to meet with the Union and negotiate a rate of pay for this new classification. If the parties cannot reach agreement, at the request of either party, the matter shall be submitted to the arbitration procedure in Article 26 of this Agreement.
Classifications 32.1 The Classification levels for Employees engaged under this agreement shall be read in accordance with the Award unless specifically amended by the terms of this Agreement. Classification levels, relativities, pay rates and other details are contained in APPENDIX 1. 32.2 An Employee not already engaged as CW4 (marker/setter) shall be paid an all-purpose allowance of 5% of his/her applicable hourly rate when performing this work. 32.3 Where any Employee on any day performs two or more classes of work to which different rates of pay are applicable, the Employee shall be paid at the higher hourly rate for the day if the Employee is required to work at that class of work for two (2) hours or more, and if for less than two (2) hours during any one (1) day the Employee will be paid the higher rate for the time so worked. 32.4 Where an Employee is elected by Employees of the Employer as a HSR and agrees to undertake the required training to fulfil the role, the Employee will be classified as the higher of CW4, or the Employee's usual classification. In addition, a HSR is entitled to an all-purpose hourly allowance for the life of this agreement as per the table at Appendix 2 – Health and Safety Representatives Allowance. (a) For clarity, an Employee is only entitled to one all-purpose hourly allowance pursuant to clauses 32.4 and 32.5.
Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.