Layout a. Estimate and quantity sheet
(1) List of all bid items
(2) Bid item quantities
(3) Specification item number
(4) Paid item description and unit of measure
b. Basis of estimate sheet (list of materials)
c. General notes and specification data.
d. Condition diagram
(1) Highway and intersection design features
(2) Roadside development
(3) Traffic control including illumination
e. Plan sheet(s)
(1) Existing traffic control that will remain (signs and markings)
(2) Existing utilities
(3) Proposed highway improvements
(4) Proposed installation
(5) Proposed additional traffic controls
(6) Proposed illumination attached to signal poles.
(7) Proposed power pole source
f. Notes for plan layout
g. Phase sequence diagram(s)
(1) Signal locations
(2) Signal indications
(3) Phase diagram
(4) Signal sequence table
(5) Flashing operation (normal and emergency)
(6) Preemption operation (when applicable)
(7) Contact responsible Agency to obtain interval timing, cycle length and offset
h. Construction detail sheets(s)
(1) Poles (State standard sheets)
(2) Detectors
(3) Pull Box and conduit layout
(4) Controller Foundation standard sheet
(5) Electrical chart i. Marking details (when applicable)
Procurement of Small Works Works estimated to cost $250,000 equivalent or less per contract, up to an aggregate amount not to exceed $800,000 equivalent, may be procured under lump-sum, fixed-price contracts awarded on the basis of quotations obtained from three (3) qualified domestic contractors in response to a written invitation. The invitation shall include a detailed description of the works, including basic specifications, the required completion date, a basic form of agreement acceptable to the Bank, and relevant drawings, where applicable. The award shall be made to the contractor who offers the lowest price quotation for the required work, and who has the experience and resources to complete the contract successfully. Part D: Review by the Bank of Procurement Decisions
Architecture The Private Improvements shall have architectural features, detailing, and design elements in accordance with the Project Schematic Drawings. All accessory screening walls or fences, if necessary, shall use similar primary material, color, and detailing as on the Private Improvements.
Configuration Management The Contractor shall maintain a configuration management program, which shall provide for the administrative and functional systems necessary for configuration identification, control, status accounting and reporting, to ensure configuration identity with the UCEU and associated cables produced by the Contractor. The Contractor shall maintain a Contractor approved Configuration Management Plan that complies with ANSI/EIA-649 2011. Notwithstanding ANSI/EIA-649 2011, the Contractor’s configuration management program shall comply with the VLS Configuration Management Plans, TL130-AD-PLN-010-VLS, and shall comply with the following:
Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.
CONTRACT WORK HOURS AND SAFETY STANDARDS As per the Contract Work Hours and Safety Standards Act (40 U.S.C. 3701-3708), where applicable, all Customer Purchase Orders in excess of ,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C. 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence.
DEVELOPMENT OR ASSISTANCE IN DEVELOPMENT OF SPECIFICATIONS REQUIREMENTS/ STATEMENTS OF WORK
Outputs Analogue and digital outputs of protected content are allowed if they meet the requirements in this section and if they are not forbidden elsewhere in this Agreement..
The Contractor must 16.1.1. treat all Authority Protected Information as confidential and safeguard it accordingly, implementing appropriate technical and organisational measures to protect Authority Protected Information against disclosure;
16.1.2. only use the Authority Protected Information for the purposes of performing its obligations under the Framework Agreement;
16.1.3. only disclose the Authority Protected Information to such Contractor Representatives that are directly involved in the performance of the Framework Agreement and need to know the information; and
16.1.4. not disclose any Authority Protected Information without the prior written consent of the Authority.
Superintendent of Schools The duly appointed executive officer of the Owner authorized to act by and through The School Board of Broward County, Florida. Referred to hereinafter as the Superintendent.
