Low-Voltage Motors Sample Clauses

Low-Voltage Motors. 1. Should there be a requirement of LV motors, the Contractor shall ensure that LV motors are procured in accordance with 240-57617975 requirements. Technical Schedules A and B in 240 – 77100923 (New LV Motor Technical Schedule AB Template) shall be provided to Employer for design acceptance.
Sample 1
AutoNDA by SimpleDocs
Low-Voltage Motors. All motors 200 hp and smaller shall be: Type Horizontal or vertical as required, single-speed, squirrel-cage induction, energy efficient, mill and chemical duty type. Cast iron frames and copper windings only. Voltage rating, phase, frequency 460 volts, three-phase, 60 Hz, for all motors rated at ½ hp through 200 hp, 115 volts, single-phase, 60 Hz, for all motor ½ hp and smaller. Horsepower rating The nameplate horsepower rating shall be equal to, or greater than, the requirements of the driven equipment when operating at design conditions and motor shall be able to handle the maximum capability of the driven equipment within their service factor rating. This relation shall be provided for all operating speeds and conditions. Service factor 1.15 Ambient temperature range Site specific ODP indoors. Nameplate Shall state the service factor and comply with NEMA MG‑1. Enclosure TEFC totally-enclosed, ventilation, and cooling as applicable to the environment. Explosion-proof motors shall be provided only where necessary to meeting the hazardous location requirements. Class of Insulation Class F Temperature rise of windings (maximum by resistance) In conformance with NEMA MG-1 standards for Class B insulation. Voltage rating, phase, frequency Voltage rating, phase, frequency Horsepower rating Horsepower rating Service factor Service factor Ambient temperature range Ambient temperature range Nameplate Nameplate Enclosure Enclosure Class of Insulation Class of Insulation Temperature rise of windings (maximum by resistance) Temperature rise of windings (maximum by resistance)
Sample 1
Low-Voltage Motors. All motors 200-hp and smaller shall have the following characteristics: Type Horizontal or vertical as required, single-speed, squirrel-cage induction, energy efficient, mill and chemical duty type. Cast iron frames and copper windings only. Voltage rating, phase, frequency 460 volts, three-phase, 60 Hz, for all motors rated at ½ hp through 200 hp, 115 volts, single-phase, 60 Hz, for all motor ½ hp and smaller. Horsepower rating The nameplate horsepower rating shall be equal to, or greater than, the requirements of the driven equipment when operating at design conditions and motor shall be able to handle the maximum capability of the driven equipment within their service factor rating. This relation shall be provided for all operating speeds and conditions. Service factor 1.15 Ambient temperature range Site specific ODP indoors. Nameplate Shall state the service factor and comply with NEMA MG‑1. Enclosure TEFC totally-enclosed, ventilation, and cooling as applicable to the environment. Explosion-proof motors shall be provided only where necessary to meeting the hazardous location requirements. Class of Insulation Class F Temperature rise of windings (maximum by resistance) In conformance with NEMA MG-1 standards for Class B insulation.
Sample 1

Related to Low-Voltage Motors

  • Network Interconnection Architecture Each Party will plan, design, construct and maintain the facilities within their respective systems as are necessary and proper for the provision of traffic covered by this Agreement. These facilities include but are not limited to, a sufficient number of trunks to the point of interconnection with the tandem company, and sufficient interoffice and interexchange facilities and trunks between its own central offices to adequately handle traffic between all central offices within the service areas at a P.01 grade of service or better. The provisioning and engineering of such services and facilities will comply with generally accepted industry methods and practices, and will observe the rules and regulations of the lawfully established tariffs applicable to the services provided.

  • Integrated Digital Loop Carriers The feeder portion of some loops may be provide by means of Integrated Digital Loop Carrier (IDLC). IDLC provides a fiber optic cable transmission path that travels directly into BellSouth’s central office local switch. Where BellSouth uses IDLC ,if technically feasible and capacity does exist, BST will provide Al-Call with a Designed DS0 UVL by using alternative provisioning techniques including but not limited to such as “hairpinning” and DAC grooming. Alternative provisioning techniques will be provided at no additional cost to Al-Call . Hairpinning involves providing a DS0 signal from an IDLC-served loop to Al-Call ’s collocation equipment by using a dedicated pathway that traverses BellSouth’s central office switch. BellSouth will provide such DS0 signal to Al-Call by establishing a copper cross connect between the BellSouth switch and Al-Call ’s collocation equipment.

  • Network Interconnection 26.1 Interconnection between the networks of different SERVICE PROVIDERs shall be as per National Standards of CCS No.7 issued from time to time by Telecom Engineering Centre (TEC) and also subject to technical feasibility and technical integrity of the Networks and shall be within the overall framework of interconnection regulations issued by the TRAI from time to time. However, if situation so arises, INTERCONNECTION with R2MF signaling may be permitted by LICENSOR.

  • SS7 Network Interconnection 15.1.1 Definition SS7 Network Interconnection is the interconnection of US LEC local Signaling Transfer Point Switches (STP) and US LEC local or tandem switching systems with BellSouth STPs. This interconnection provides connectivity that enables the exchange of SS7 messages among BellSouth switching systems and databases (DBs), US LEC local or tandem switching systems, and other third-party switching systems directly connected to the XxxxXxxxx XX0 network.

Time is Money Join Law Insider Premium to draft better contracts faster.