Measurement criteria for A Sample Clauses

Measurement criteria for A weighted sound pressure level The background, or ambient noise, shall be measured for a duration of at least 10 seconds. A 10 second sample taken from these measurements shall be used to calculate the reported background noise, taking account to ensure the 10 seconds sample selected is representative of the background noise in absence of any transient disturbance. The measurements shall be made with the same microphones and microphone locations used during the test When testing in an indoor facility, the noise emitted by the roller-bench, chassis dynamometer, or other test facility equipment, without the vehicle installed or present, inclusive of the noise caused by air handling, facility vehicle cooling, shall be reported as the background noise. The recorded maximum A-weighted sound pressure level from both microphones shall be reported as the background noise, Lbgn, along with the maximum to minimum range of the background noise from both microphones, ∆Lbgn, p-p, and the one-third-octave frequency spectrum, corresponding to the reported maximum level of background noise, shall be reported. Figure 2 provides graphical information on the determination of the range of background noise. When analysis in one-third octaves is required, the background noise shall meet the requirements of paragraph 3.3.3.
Sample 1Sample 2
AutoNDA by SimpleDocs

Related to Measurement criteria for A

  • Performance Measurement Satisfactory performance of this Contract will be measured by:

  • Selection Criteria for Awarding Task Order The Government will award to the offeror whose proposal is deemed most advantageous to the Government based upon an integrated assessment using the evaluation criteria. The Government will evaluate proposals against established selection criteria specified in the task order RFP. Generally, the Government's award decision will be based on selection criteria which addresses past performance, technical acceptability, proposal risk and cost. Among other sources, evaluation of past performance may be based on past performance assessments provided by TO Program Managers on individual task orders performed throughout the life of the contract. The order of importance for the factors will be identified in the RFP for the specified task order.

  • Evaluation Criteria 5.2.1. The responses will be evaluated based on the following: (edit evaluation criteria below as appropriate for your project)

  • PERFORMANCE MEASUREMENTS Upon a particular Commission’s issuance of an Order pertaining to Performance Measurements in a proceeding expressly applicable to all CLECs generally, BellSouth shall implement in that state such Performance Measurements as of the date specified by the Commission. Performance Measurements that have been Ordered in a particular state can currently be accessed via the internet at xxxx://xxxx.xxxxxxxxx.xxx. The following Service Quality Measurements (SQM) plan as it presently exists and as it may be modified in the future, is being included as the performance measurements currently in place for the state of Tennessee. At such time that the TRA issues a subsequent Order pertaining to Performance Measurements, such Performance Measurements shall supersede the SQM contained in the Agreement. BellSouth Service Quality Measurement Plan‌ (SQM) Tennessee Performance Metrics Measurement Descriptions Version 2.00 Issue Date: July 1, 2003 Introduction

  • Selection Criteria Each Contract is secured by a new or used Motorcycle. No Contract has a Contract Rate less than 1.00%. Each Contract amortizes the amount financed over an original term no greater than 84 months (excluding periods of deferral of first payment). Each Contract has a Principal Balance of at least $500.00 as of the Cutoff Date.

  • Criteria (1) Annual Evaluation Criteria. All performance evaluations shall be based upon assigned duties, and shall carefully consider the nature of the assignment in terms, where applicable, of:

  • Service Eligibility Criteria 4.3.4.1 High capacity EELs must comply with the following service eligibility requirements:

  • Criteria for Performance Assessment A. A teacher’s performance shall be assessed based on the criteria set forth in the evaluation instrument, Appendix D.

  • Exclusion Criteria Subjects fulfilling any of the following criteria are not eligible for participation in this study.

  • Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.

Time is Money Join Law Insider Premium to draft better contracts faster.