Panel Selection 1. The Parties shall apply the following procedures in selecting a Panel: (a) the Panel shall comprise 3 members; (b) within 15 days following the date of the establishment of the Panel, each Party shall nominate a Panelist; (c) the Parties shall endeavor
2. If a Panelist appointed under this Article resigns or becomes unable to act, a successor Panelist shall be appointed within 30 days in accordance with the selection procedure as prescribed for the appointment of the original Panelist and the successor shall have all the powers and duties of the original Panelist. The work of the Panel shall be suspended during the appointment of the successor Panelist.
Shift Selection Employee assignments within the Patrol Bureau will occur between approximately April 1-15 and shall be awarded based upon seniority. Approximately three (3) months before then the Department will publish a call for written requests on shift assignment. Employees will make their first three (3) choices known. Employees will learn of the assignment, including days off associated with their assignment, immediately after the bidding process is completed. Assignments will take effect on the schedule immediately following July 1st. Residence Hall assignments will be made prior to all others. No officer will be required to work a Residence Hall assignment in consecutive years. Assignment of the remaining officers will begin with selection(s) for day and night shifts. The bid for assignments will continue until all positions are filled. The following general rules apply to assignments:
1. During the term of this Agreement, no employee will be reassigned to a different shift other than the shift awarded by seniority except in situations where the University cannot continue to provide police services. In the event a shift reassignment must occur, it will be offered to volunteers based on seniority. If there are no volunteers it will be assigned to the least senior officer in the department.
2. Shift selection shall be an appropriate subject for the Joint Labor/Management Committee.
3. If a shift becomes available as a result of trainees being released for duty, and if there is at least four (4) months until the next shift change, the shift will be posted and awarded by seniority. The new trainee released for duty will take the senior officers shift. If no employee desires the shift, the trainee scheduled for assignment will be assigned that shift. The parties recognize that for the betterment of the Department it may be necessary to assign a trainee to a specific shift.
4. Voluntary shift trades will be allowed as long as overtime costs are not incurred.
5. Except in a bona fide emergency, no employee shall be assigned to work more than sixteen (16) hours in a twenty-four (24) hour period, provided however employees may volunteer to work up to eighteen (18) hours in a twenty-four (24) hour period.
Single Source Selection Services for tasks in circumstances which meet the requirements of paragraph 3.10 of the Consultant Guidelines for Single Source Selection, may, with the Association's prior agreement, be procured in accordance with the provisions of paragraphs 3.9 through 3.13 of the Consultant Guidelines.
Least-cost Selection Services for assignments which the Association agrees meet the requirements of paragraph 3.6 of the Consultant Guidelines may be procured under contracts awarded on the basis of Least-cost Selection in accordance with the provisions of paragraphs 3.1 and 3.6 of the Consultant Guidelines.
Desirable Selection Criteria Post registration qualification in the area of specialty or evidence of significant progression towards one.
Site Selection 5.1.1 If the parties have not designated the street address of the Franchised Location on Exhibit A on the Effective Date, Franchisee shall identify, submit and obtain Franchisor’s prior written approval of the Franchised Location meeting the requirements of this Agreement prior to entering a lease or sublease for the Franchised Location. Franchisee shall provide Franchisor all information required by Franchisor, as determined by Franchisor in Franchisor’s sole determination, necessary for Franchisor to evaluate the Franchised Location. Franchisor shall have ten (10) business days to review Franchisee’s written site proposal for the Franchised Location and notify Franchisee of its approval or disapproval in writing. Franchisor’s failure to respond within ten (10) business days shall signify Franchisor’s disapproval of the site. Franchisor shall not unreasonably withhold Franchisor’s approval of a proposed site for the Franchised Location.
5.1.2 Franchisee must have a site for the Franchised Location approved by Franchisor, receive the opening notice from Franchisor described in Section 5.4 below, and open Franchisee’s Franchised Business for business within six (6) months from the Effective Date, except as otherwise provided in Section
5.1.3 All matters related in any way to Franchisee’s site are Franchisee’s sole responsibility, regardless of any assistance Franchisor may choose to provide. Franchisee is responsible for obtaining any architectural and engineering services required for Franchisee’s facility and for ensuring its compliance with local law. Neither Franchisor, nor any other person or company associated with Franchisor shall have any liability for any site‐related matter. Xxxxxxxxxx agrees not to make any claims against Franchisor and/or any of Franchisor’s affiliates or associates with regard to such matters.
5.1.4 If Franchisor makes a loan to Franchisee for (i) Franchisee’s purchase of the franchise for the Franchised Business; (ii) the remodeling of the Franchised Location; (iii) the transfer of any interest in this franchise or this Agreement; or (iv) any other purpose; Franchisee shall open (or re‐open, as the case may be), the Franchised Business for business within sixty (60) days from the loan origination date.
Vacation Selection Employees who have not selected their vacation periods by November 15th shall not be entitled later to select vacation periods by seniority. Employees who do not select all of their vacation entitlements on the calendar shall be allowed to schedule vacation at a later date, provided that this selection does not affect the scheduled vacations of other employees.
Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where Xxxx has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to Xxxx. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for Xxxx (e.g. hairpinning):
1. Roll the circuit(s) from the IDLC to any spare copper that exists to the customer premises.
2. Roll the circuit(s) from the IDLC to an existing DLC that is not integrated.
3. If capacity exists, provide "side-door" porting through the switch.
4. If capacity exists, provide "Digital Access Cross Connect System (DACS)- door" porting (if the IDLC routes through a DACS prior to integration into the switch).
2.6.2 Arrangements 3 and 4 above require the use of a designed circuit. Therefore, non- designed Loops such as the SL1 voice grade and UCL-ND may not be ordered in these cases.
2.6.3 If no alternate facility is available, and upon request from Xxxx, and if agreed to by both Parties, BellSouth may utilize its Special Construction (SC) process to determine the additional costs required to provision facilities. Xxxx will then have the option of paying the one-time SC rates to place the Loop.
Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.
