Plastics. Cerus understands that significant testing costs may be required for the qualification and submission of potential changes described in Section 2.2(e). Cerus agrees to fully fund any qualification and validation work required specifically for use of plastics in the Manufactured Products. Fenwal will fund the generic qualification and validation work that would be required for material changes required for use of such plastics in Fenwal products.
Plastics. In the event plastics are used in the Tenant’s Use, Tenant must remove said plastics no later than thirty (30) days after use. Plastics will not be disked into the ground. All plastics will be properly removed and disposed of in accordance with Legal Requirements, as that term is defined below. CW Landlord KM Tenant
Plastics. Cerus understands that Fenwal may receive, from time-to-time, “Supplier Notice of Change” notifications from Baxter for any of the formulations for the key plastics used in the Platelet and Plasma Sets manufactured by Baxter. No such changes, however, shall cause the Manufactured Products to fail to meet any regulatory requirements. Additionally, Cerus reserves any and all rights, and remedies it may have against Baxter, for such plastics under the Original Supply Agreement. Allocation of costs for such changes is further described in Section 4.4(e). [*] = CERTAIN CONFIDENTIAL INFORMATION CONTAINED IN THIS DOCUMENT, MARKED BY BRACKETS, HAS BEEN OMITTED AND FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION PURSUANT TO RULE 24b-2 OF THE SECURITIES EXCHANGE ACT OF 1934, AS AMENDED.
Plastics. Custom per card Per Quote Hot Stamp Die per die Per Quote Graphics per design Per Quote Agent/Cardholder Setup for Standard Plan 600.00 Minimum Monthly Fee 300.00 (Minimum monthly fee does not include the following: Base, Compliance, Authorizations, Interchange, Transmission, Additional. programming, Equipment, Training, or Special fees.)
Plastics. (excluding plastics and postage/delivery)
Plastics. Supplier and Insulet agree to the following volume-based-pricing for plastic components for the Insulet controlled materials purchased under this Agreement. Insulet intends to purchase at least half of its monthly requirement for these plastics from Supplier: Table A – Plastics Group 1 Drawing Description [*] [*] [*] [*] [*] [*] [*] [*] [*] [*] * Confidential treatment has been requested for portions of this exhibit. The copy filed herewith omits the information subject to the confidentiality request. Omissions are designated as [*]. A complete version of this exhibit has been filed separately with the Securities and Exchange Commission. Table B – Plastics Group 2 Drawing Description [*] [*] [*] [*] [*] [*] [*] [*]
1. In the event that Insulet fails to purchase half of its plastics requirement for Plastics Group 1 and Plastics Group 2 from Supplier for a period of more than 6 consecutive months after all parts are fully qualified and available for production, Supplier may increase the Price set forth above by [*]. A component of the plastic annual volume-based-pricing is based on certain resin pricing as follows:
a) if Insulet-controlled resin pricing increases or decreases, the plastic annual volume-based-pricing will increase or decrease accordingly on a quarterly basis, once approved by both Parties; and b) resin pricing for resin purchased by supplier will be reviewed on a quarterly basis and reconciled once approved by both Parties. Supplier will provide resin cost, supporting documentation and payments to resin suppliers to support the reconciliation process.
2. The Plastic Parts Price supplied is based on total Insulet-controlled supply chain resin pricing. If this Insulet controlled resin pricing increases or decreases, the Plastics Part Price will increase or decrease by the same dollar value on a quarterly basis. This adjustment will be part of the quarterly review in section D.5 above.
Plastics. Manufacturing of PET containers, tubes, tanks, and clo- sures for food packings.
Plastics. Custom per card Per Quote Hot Stamp Die per die Per Quote Graphics per design Per Quote Card Application Holder per holder 1.75 Applications - Regular per application .25 (300 minimum) Applications - Gold per application .60 (300 minimum) Gold Brochures per brochure .80 Business Card Features and Benefits per brochure .75
Plastics. Type A ABS (acrylonitrile-butadiene-styrene copolymer) 9003-56-9 solid Type A Polyurethane solid Type A TPE (thermoplastic elastomer) solid Type B Type C Combustible Fiber None Cryogenic, Flammable None Cryogenic, Oxidizing Cryogenic Oxygen 7782-44-7 liquid/gas 500 gals. outdoor storage Explosives None Flammable Solids None Flammable Gas None Organic Peroxide None Oxidizer None Oxidized - Gas None Pyrophoric None Unstable (reactive) None Water Reactive None
