Construction and Installation Tests Sample Clauses

Construction and Installation Tests. (a) The adequacy of construction and installation of components and systems shall be verified by construction inspection and installation tests. During the construction period, Contractor shall erect the structure, install plant equipment and perform construction verification and inspection tests. All of these activities shall be executed, controlled, and documented in accordance with Contractor’s approved procedures. (b) During construction, installation of components associated with the various systems will be completed. The associated piping, wiring, equipment, and controls shall be verified to be installed in accordance with approved final design drawings. Construction and Installation Tests shall be performed and all appropriate documentation and exceptions to construction verification tests, or incomplete tests shall be recorded as turnover exceptions. On a system basis, completion of this program shall demonstrate that the system is ready for preoperational testing. Where applicable, Preoperational Tests may proceed prior to completion of this program.
Sample 1Sample 2
AutoNDA by SimpleDocs
Construction and Installation Tests. (a) The adequacy of construction and installation of components and systems shall be verified by construction inspection and installation tests. During the construction period, Contractor erects the structure, installs plant equipment and performs construction verification and inspection tests. All of these activities are executed, controlled, and documented in accordance with Contractor’s approved procedures. “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures During construction, Contractor completes the Construction and Installation Test program in which various electrical and mechanical tests are performed including but not limited to the following: · Cleaning and flushing · Hydrostatic testing · Checks of electrical wiring · Valve testing · Energization and operation of equipment · Calibration of instrumentation (b) During construction, Contractor completes the building of components associated with the various systems. The associated piping, wiring, equipment, and controls are verified to be installed in accordance with approved final design drawings. Construction and Installation Tests are performed and all appropriate documentation and exceptions to construction verification or tests, or incomplete tests shall be recorded as Turnover exceptions. On a system basis, completion of this program demonstrates that the system is ready for preoperational testing. The system shall be turned over to the Joint Test Working Group.
Sample 1
Construction and Installation Tests. Preoperational Tests, Start-up Tests and the Performance Tests, each as described in this Article 11.
Sample 1
Construction and Installation Tests. (a) The adequacy of construction, installation, and preliminary operation of Equipment and Systems shall be verified by a program of Construction and Installation Tests. In this program, examples of various electrical and mechanical tests that shall be performed include the following: • Cleaning and flushing • Hydrostatic testing • Checks of electrical wiring • Valve testing • Energization and operation of Equipment • Calibration of instrumentation • Equipment functional testing (to the extent feasible) • Balancing of rotating Equipment (to the extent feasible) • Rotation checks. On a System basis, completion of this program shall demonstrate that each System is ready for Preoperational Tests. Contractor will develop the Construction and Installation Test procedures consistent with its procedures for the Standard Plant and will provide the Construction and Installation Test procedures to Owner at least thirty (30) Days in advance of the testing for Owner’s review and Acceptance, which Acceptance shall not be unreasonably withheld. Owner will Accept such Construction and Installation Test procedures or provide a written description of its proposed changes thereto within fifteen (15) Days of its receipt of such Construction and Installation Test procedures. If Owner requests a change to the Construction and Installation Test procedures that goes beyond the scope of the Standard Plant procedures, then Contractor shall be entitled to seek a Change Order pursuant to Article 9. Contractor shall provide the scheduled testing dates to Owner in writing at least fourteen (14) Days in advance so that Owner may witness the tests. Contractor shall not change the scheduled test dates without giving Owner at least fourteen (14) Days prior Notice. Owner is not required to witness these tests. Contractor shall perform the Construction and Installation Tests, and shall supply detailed Documentation, as specified in the test procedures, of the testing and the test results to Owner within thirty (30) Days after the test is completed. Should corrective work be necessary as a result of the test, Contractor shall re-perform any testing at its own cost promptly after the corrective work is performed, as required by Good Industry Practices.
Sample 1
Construction and Installation Tests. (a) The adequacy of construction and installation of components and systems shall be verified by construction inspection and installation tests. During the construction period, Contractor erects the structure, installs plant equipment and performs construction verification and inspection tests. All of these activities are executed, controlled, and documented in accordance with Contractor's approved procedures. “[**]” in this Exhibit 10.02 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. During construction, Contractor completes the Construction and Installation Test program in which various electrical and mechanical tests are performed including but not limited to the following: · Cleaning and flushing · Hydrostatic testing · Checks of electrical wiring · Valve testing · Energization and operation of equipment · Calibration of instrumentation (b) During construction, Contractor completes the building of components associated with the various systems. The associated piping, wiring, equipment, and controls are verified to be installed in accordance with approved final design drawings. Construction and Installation Tests are performed and all appropriate documentation and exceptions to construction verification or tests, or incomplete tests shall be recorded as Turnover exceptions. On a system basis, completion of this program demonstrates that the system is ready for preoperational testing. The system shall be turned over to the Joint Test Working Group.
Sample 1
Construction and Installation Tests. (a) The adequacy of construction and installation of components and systems shall be verified by construction inspection and installation tests. During the construction period, Contractor erects the structure, installs plant equipment and performs construction verification and inspection tests. All of these activities are executed, controlled, and documented in accordance with Contractor's approved procedures. During construction, Contractor completes the Construction and Installation Test program in which various electrical and mechanical tests are performed including but not limited to the following: • Cleaning and flushing • Hydrostatic testing • Checks of electrical wiring • Valve testing • Energization and operation of equipment • Calibration of instrumentation (b) During construction, Contractor completes the building of components associated with the various systems. The associated piping, wiring, equipment, and controls are verified to be installed in accordance with approved final design drawings. Construction and Installation Tests are performed and all appropriate documentation and exceptions to construction verification or tests, or incomplete tests shall be recorded as Turnover exceptions. On a system basis, completion of this program demonstrates that the system is ready for preoperational testing. The system shall be turned over to the Joint Test Working Group.
Sample 1
Construction and Installation Tests. (a) The adequacy of construction and installation of components and systems shall be verified by construction inspection and installation tests. During the construction period, Contractor erects the structure, installs plant equipment and performs construction verification and inspection tests. All of these activities are executed, controlled, and documented in accordance with Contractor's approved procedures. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures During construction, Contractor completes the Construction and Installation Test program in which various electrical and mechanical tests are performed including but not limited to the following: • Cleaning and flushing • Hydrostatic testing • Checks of electrical wiring • Valve testing • Energization and operation of equipment • Calibration of instrumentation (b) During construction, Contractor completes the building of components associated with the various systems. The associated piping, wiring, equipment, and controls are verified to be installed in accordance with approved final design drawings. Construction and Installation Tests are performed and all appropriate documentation and exceptions to construction verification or tests, or incomplete tests shall be recorded as Turnover exceptions. On a system basis, completion of this program demonstrates that the system is ready for preoperational testing. The system shall be turned over to the Joint Test Working Group.
Sample 1
AutoNDA by SimpleDocs

Related to Construction and Installation Tests

  • Maintenance Repairs Utility Installations Trade Fixtures and Alterations (a) Section 8.1(a) is amended in its entirety to read as follows: Subject to the provisions of Sections 8.2, 10, and 15, Tenant shall, at Tenant's sole cost and expense and at all times, keep the Building Complex and every part thereof in good order, condition and repair (whether or not the need for such repairs occurs as a result of Tenant's use, any prior use, the elements or the age of such portion of the Building Complex), including, without limiting the generality of the foregoing, plumbing, electrical lighting facilities, boilers, fired or unfired pressure vessels, fire hose connections, fixtures, interior walls, exterior walls, roof, ceilings, floors, windows, doors, plate glass, and skylights, parking areas and lighting, driveways, sidewalks, landscaping, irrigation systems, and subject to Section 8.1(b) below, heating, air conditioning and ventilating systems, but excluding any items which are the responsibility of Landlord pursuant to Section 8.2 below. Tenant, in keeping the Building Complex in good order, condition and repair, shall exercise and perform good maintenance practices, including, without limitation, providing janitorial services to the Building Complex substantially equivalent to those attached hereto as Exhibit I and, snow, ice and trash removal service. Tenant's obligations shall include restorations, replacements or renewals when necessary to keep the Building Complex and all improvements thereon or a part thereof in good order, condition and state of repair. (b) Section 8.1(b) is amended in its entirety to read as follows: Tenant shall procure and pay the cost of a contract for maintenance of the heating, air conditioning and ventilating systems for the Building Complex with a reputable contractor licensed in the State of Colorado and reasonably satisfactory to Landlord. (c) Section 8.1(c) is amended to replace, in both places where it is used, the word "Premises" with the words "Building Complex" and to add the words "including, without limitation, the Premises," before the words "after twenty". (d) Section 8.2 is amended in its entirety to read as follows:

  • Maintenance Repairs and Alterations 7.1 Lessee's Obligations. -------------------- (a) Subject to Lessor's obligations under Paragraphs 6.2(b), 6.3(a), 7.3, 9 and 40, Lessee shall keep in good order, condition and repair the non- structural elements of the Premises and every part thereof, (whether or not the need for such repairs occurs as a result of Lessee's use, any prior use, the elements or the age of such portion of the Premises) including, without limiting the generality of the foregoing, all exposed plumbing, heating and air conditioning, ventilating, electrical, lighting facilities and equipment within the Premises, fixtures, walls (interior and nonstructural elements of exterior), ceilings, floors, windows, doors, plate glass and skylights located within the Premises, and all driveways, parking lots and striping thereon, landscaping, exterior lighting, fences and signs located on the Premises and sidewalks and parkways adjacent to the Premises. If the cost of repairing an element of the Premises is covered by a warranty obtained by Lessor from a third party contractor, subcontractor, consultant or material supplier in connection with construction work performed on the Premises prior to the Effective Date, Lessor shall make available such warranty to Lessee and shall assign to Lessee Lessor's rights thereunder, provided that Lessee shall not take any action which shall invalidate any such warranty or derogate from Lessor's remedies or recourse thereunder. (b) Lessee shall maintain the Premises as provided in Paragraph 7. I (a) and in accordance with the requirements of all Laws and any covenants or restrictions as may from time to time be applicable to Lessee's specific manner of use of the Premises and the conduct and operation of Lessee's business. Lessee, in keeping the Premises in good order, condition and repair, shall exercise and perform good maintenance practices and any damage or deterioration shall not be deemed "ordinary wear and tear" if the same could have been prevented by good maintenance practice. Lessee's obligations shall include restorations, replacements or renewals when determined not to be due to ordinary wear and tear or when made necessary due to failure to perform proper maintenance. (c) If the term of this Lease, as the same may be extended or renewed, exceeds five (5) years, Lessor shall have the right to require Lessee to repaint the exterior of THE improvements. but not more often than once every five (5) years, as reasonably necessary. (d) Lessee's obligations under this Paragraph 7.1 shall not apply to replacement, repair or restoration of items which are Lessor's obligation to replace, repair or restore pursuant to the terms of Paragraph 6.3(a) (relating to Existing Defects) Paragraph 7.3(a) relating to structural repairs and certain replacements) Paragraph 9 (relating to destruction of the Premises) or Paragraph 14 (relating to condemnation of the Premises).

  • Construction of the Tenant Improvements (a) Tenant shall construct and install the Tenant Improvements in a good and workmanlike manner, in compliance with all Laws and in accordance with this Exhibit B. Tenant’s proposed architect/engineer, general contractor, and fire protection, plumbing, HVAC and electrical subcontractors are subject to Landlord’s prior approval. Promptly following the selection and approval of the architect/engineer, Tenant shall forward to said architect/engineer (and copy Landlord on the transmittal) Landlord’s building standards heretofore delivered to Tenant, and Tenant shall cause said architect/engineer to comply with said building standards. Promptly following the selection and approval of the general contractor, Tenant shall forward to said general contractor (and copy Landlord on the transmittal) Landlord’s fire protection, plumbing, HVAC and electrical specifications and Landlord’s rules of conduct, all of which have been delivered to Tenant prior to the date of this Lease, and Tenant shall cause said general contractor to comply with said specifications and rules of conduct. At Landlord’s request, Tenant shall coordinate a meeting among Landlord (who will reasonably make its representative available for such meeting), Tenant and Tenant’s general contractor to discuss the Building systems and other matters related to the construction of the Tenant Improvements. (b) Promptly following the date hereof, Tenant shall prepare and submit to Landlord a set of permittable construction drawings (the “CDs”), based on the preliminary plans attached hereto as Exhibit B-2 and made a part hereof (the “Preliminary Plans”), covering all work to be performed by Tenant in constructing the Tenant Improvements. Tenant shall have no right to make any Tenant Improvements that would materially alter the exterior appearance of the Building or the Building systems without Landlord’s prior approval. Landlord shall have fifteen (15) days after receipt of the CDs in which to review the CDs and in which to give Tenant written notice of its approval of the CDs or its requested changes to the CDs in reasonably sufficient detail so as to allow Tenant to make the requested changes (provided that Landlord shall not be permitted to request a change that is inconsistent with the Preliminary Plans). If Landlord requests any changes to the CDs, Tenant shall make such changes and shall, within fifteen (15) days of its receipt of Landlord’s requested changes (if any), submit the revised portion of the CDs to Landlord. Landlord shall have five (5) business days after receipt of the revised CDs in which to review said revised CDs and in which to give to Tenant written notice of its approval of the revised CDs or its requested changes thereto. This process shall continue until such time, if at all, that Landlord approves the CDs in accordance with this Section 2. Tenant shall at all times in its preparation of the CDs, and of any revisions thereto, act reasonably and in good faith. Landlord shall at all times in its review of the CDs, and any revisions thereto, act reasonably and in good faith.

  • Maintenance, Alteration and Repair (a) Resident is responsible for and agrees to take good care of the premises, fixtures and all common areas. Resident may not remove any of Owner’s property and will not perform any repairs, upgrades, painting, wallpapering, electric changes or other alterations of the premises without prior written consent from Owner. Resident will be responsible for damage from waste stoppages caused by foreign or improper objects or improper use in lines serving bathrooms, damage to fixtures, appliances, doors, windows, screens, damage from water faucets left on or from doors left open, and repairs or replacements to alarm devices necessitated by misuse or damage by Resident and/or guests. Extraordinary appliances or furnishings such as satellite dishes, hot tubs, pool tables, water beds or high utility-consuming devices may not be installed or placed on the premises or anywhere at the Property without Owner’s prior written consent, in its sole discretion. SAMPLE (b) In the case of a malfunction of any utilities or damage by fire, water or similar cause, or any water leak, suspected mold or microbial growth, electrical problem, broken glass, broken lock or any other condition that Resident reasonably believes poses a hazard to health and safety, Resident must promptly notify Owner in writing. Owner will act with reasonable time and diligence in making repairs and reconnections; Resident may not withhold or reduce payment of rent or other charges during such time. Maintenance and repair requested by Resident will generally be performed between 8am and 8pm, unless the work is considered an emergency, in which case work may take place at any time. Owner may temporarily disconnect equipment or utilities to avoid property damage and/or to perform repairs requiring such interruption, in Owner’s sole discretion. Owner will not be liable for any inconvenience, discomfort, disruption or interference with Resident use of the premises because of ongoing repairs, alterations or improvements to the Property or any apartment. (c) Following move-in, Resident is responsible for providing and changing all light bulbs and batteries (for smoke detectors and remote controls) in the assigned apartment. A written maintenance report requesting assistance in changing these items may be submitted for maintenance staff assistance, with extra charges payable by Resident as applicable per Owner’s published rates. From time to time, maintenance staff may enter the assigned apartment with or without notice to inspect and change furnace filters and to provide pest control.

  • Delivery and Installation Delivery 7.1 Provided the conditions in clause 1.5 have been satisfied, we must, or must procure, the delivery of the System to the Premises. 7.2 The risk of loss or theft of, or damage to, the System passes to you on delivery of the System to the Premises.

  • MAINTENANCE, REPAIRS, OR ALTERATIONS The Tenant shall, at their own expense and at all times, maintain premises in a clean and sanitary manner, and shall surrender the same at termination hereof, in as good condition as received, normal wear and tear excepted. The Tenant may not make any alterations to the leased premises without the consent in writing of the Landlord. The Landlord shall be responsible for repairs to the interior and exterior of the building. If the Premises includes a washer, dryer, freezer, dehumidifier unit and/or air conditioning unit, the Landlord makes no warranty as to the repair or replacement of units if one or all shall fail to operate. The Landlord will place fresh batteries in all battery-operated smoke detectors when the Tenant moves into the premises. After the initial placement of the fresh batteries it is the responsibility of the Tenant to replace batteries when needed. A monthly "cursory" inspection may be required for all fire extinguishers to make sure they are fully charged.

  • Installation, Maintenance, Testing and Repair Unless otherwise agreed in writing by the Parties, to the extent required by Applicable Law, Interconnection provided by a Party shall be equal in quality to that provided by such Party to itself, any subsidiary, affiliates or third party. If either Party is unable to fulfill its obligations under this Section 14.2, it shall notify the other Party of its inability to do so and will negotiate alternative intervals in good faith. The Parties agree that to the extent required by Applicable Law, the standards to be used by a Party for isolating and clearing any disconnections and/or other outages or troubles shall be at parity with standards used by such Party with respect to itself, any subsidiary, affiliate or third party.

  • Installation and Maintenance Except for the bi‐directional and production metering equipment owned by the City, all equipment on Customer’s side of the delivery point, including the required disconnect device, shall be provided and maintained in satisfactory operating condition by Customer and shall remain the property and responsibility of the Customer. The City will bear no responsibility for the installation or maintenance of Customer’s equipment or for any damage to property as a result of any failure or malfunction thereof. The City shall not be liable, directly or indirectly for permitting or continuing to allow the interconnection of the Facility or for the acts or omissions of Customer or the failure or malfunction of any equipment of Customer that causes loss or injury, including death, to any party.

  • Utility Installations Trade Fixtures Alterations 8.3.1 The term “Utility Installations” refers to all floor and window coverings, air and/or vacuum lines, power panels, electrical distribution, security and fire protection systems, communication cabling, lighting fixtures, HVAC equipment, plumbing, and fencing in or on the Premises. The term “Trade Fixtures” shall mean Lessee’s machinery and equipment that can be removed without doing material damage to the Premises. The term “Alterations” shall mean any modification of the improvements, other than Utility Installations or Trade Fixtures, whether by addition or deletion. “Lessee Owned Alterations and/or Utility Installations” are defined as Alterations and/or Utility Installations made by Lessee that are not yet owned by Lessor pursuant to Section 8.4.1.

  • ALTERATIONS & IMPROVEMENTS Tenant shall not make any alterations, additions or improvements or do any type of construction to the Property without first obtaining Landlord's written consent. Unless prior written agreement is reached between Tenant and Landlord, any such alterations, additions, improvements or construction shall become part of the Property and shall remain at the expiration of Tenant's Lease term. If Landlord approves of alterations, additions, improvements or construction in writing and Tenant intends to use contractors to undertake such work, the contractors must first be approved in writing by Landlord. Tenant must also place any funds to cover the amount of any alterations, additions, improvements or construction in an escrow account approved by Landlord before the commencement of the work. Landlord shall designate the times and manner of the work being done, exclusively.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!