Drop test. 3.2.1. When the headform impactors are dropped from a height of 376 mm ± 1 mm in accordance with paragraph 3.3. below, the peak resultant acceleration measured by one triaxial (or three uniaxial) accelerometer (accelerometers) in the headform impactor shall be:
Drop test. Pass the more rigorous of: (a) the SAAMI Standard drop test in effect on the date the firearm is sold; or (b) the following test: The gun shall be test-loaded, set such that it is ready to fire and dropped onto a steel plate or equivalent material of similar hardness from a height of one meter from each of the following positions: (1) normal firing position; (2) upside down; (3) on the grip; (4) on the muzzle; (5) on either side; and (6) on the exposed hammer or striker (or, if no exposed hammer or striker, on the rearmost part of the gun). If the gun is so designed so that its hammer or striker may be set in other positions, it shall be tested with the hammer or striker in each such position (but otherwise ready to fire).
Drop test. Door operation drops properly during simulated drop test. - Door closes at least 6" per second and not more than 24" per second. - Reset door according to manufacturer's specifications. - Second drop test completed to test the resetting of door to manufacturer's specifications worked properly. - Lubrication of all bearings, guides and gears with factory approved lubricants. - Adjustment and alignment of door to ensure it hangs level within the guides. For additional information regarding fire doors and their maintenance please visit xxx.Xxxxxxxx.xxx. NOTES: 8/4/2020 xxxxx://xxxx000.xx - For safety reasons, no traffic will be allowed in or out of the opening while service is being performed. - The customer is responsible for providing security, if required at any time. - Overhead Door Company of Washington, DC will not be responsible for security related costs for any reason. - Any additional work required is not part of this quote and will be quoted at a later date, if needed. - Wage scale rates (in accordance with the Xxxxx Xxxxx Act) are NOT included in our pricing. - All work is quoted for normal business hours. - Price includes all applicable state and local taxes. We appreciate the opportunity of quoting you on this project. Your satisfaction and business are important to us. Should you have any questions, please contact our Service Department. Service will not be rendered under this agreement in any case that the customer has a past due account. It is agreed that either party will have the right to cancel this program with thirty (30) days written notice.
Drop test. Drop tests shall be conducted in accordance with [Table B-2-1.1] of this section. In each case, Face, Edge and Corner drops shall be performed. Table B-2-1.1. Height and Number of Drops GROSS WEIGHT Not Exceeding DIMENSIONS ON ANY EDGE Not Exceeding FACE DROP TEST (Height & Number of Drops) EDGEWISE DROP TEST (Height & Number of Drops) CORNERWISE DROP TEST (Height & Number of Drops) Category I Category II Category I Category II Category I Category II 160 Drops at 16 Drops at 80 Drops at 8 Drops at 40 Drops at 4 Drops at 50 lbs. 36 in. 30 in. 22 in. 36 in. 27 in. 36 in. 27 in. 100 lbs. 48 in. 21 in. 16 in. 36 in. 27 in. 36 in. 27 in. 150 lbs. 60 in. 18 in. 14 in. 36 in. 27 in. 36 in. 27 in. 200 lbs. 60 in. 16 in. 12 in. 36 in. 27 in. 36 in. 27 in. 600 lbs. 72 in. 16 in. 12 in. 36 in. 27 in. 36 in. 27 in. 3000 lbs. No Limit 16 in. 12 in. 24 in. 18 in. 24 in. 18 in. No Limit No Limit 16 in. 12 in. 12 in. 9 in. 12 in. 9 in.
Drop test. 2.8.1. Test procedure One finished container shall be drop tested at ambient temperature without internal pressurization or attached valves. The surface onto which the containers are dropped shall be a smooth, horizontal concrete pad or flooring. The drop height (Hd) shall be 2 m (measured to the lowest point of the container). The same empty container shall be dropped: - in a horizontal position, - vertically on each end, - at an angle of 45°. Following the drop test, the containers shall be submitted to an ambient temperature pressure cycling test according the requirements of paragraph 2.3.6.1. of this annex.
