FABRICATION, GENERAL Sample Clauses

FABRICATION, GENERAL. A. Assemble items in the shop to greatest extent possible to minimize field splicing and assembly. Disassemble units only as necessary for shipping and handling limitations. Clearly mark units for reassembly and coordinated installation. Use connections that maintain structural value of joined pieces.
Sample 1
AutoNDA by SimpleDocs
FABRICATION, GENERAL. A. General: 1. Custom fabricate sheet metal flashing and trim to comply with recommendations in SMACNA's "Architectural Sheet Metal Manual" that apply to design, dimensions, metal, and other characteristics of item indicated. Shop fabricate items where practicable. Obtain field measurements for accurate fit before shop fabrication. 2. All finish flashings, where applicable, must be fully engaged and continuously crimped onto the underlying cleat. 3. All points where the sheet metal flashing ends or transitions into a different flashing detail shall be flashed with a field-formed sheet metal closure. The use of mastic or excessive caulking shall not be acceptable. B. Fabricate sheet metal flashing and trim in thickness or weight needed to comply with performance requirements, but not less than that specified for each application and metal. C. Fabricate sheet metal flashing and trim without excessive oil canning, buckling, and tool marks and true to line and levels indicated, with exposed edges folded back to form hems. D. Sealed Joints: Form nonexpanding but movable joints in metal to accommodate elastomeric sealant to comply with SMACNA recommendations.
Sample 1
FABRICATION, GENERAL. .1 Curtain wall shall be constructed in shop fabricated units, and shop glazed and delivered to the site in a panelized form. .2 Fabricate sections to accommodate and interface with work of other contracts by means of rabbets, interlocks, miscellaneous angles, trim and filler sections, as required. .3 Component fastenings shall be concealed throughout of adequate strength fabricated from stainless steel and shall be fusion welded. .4 Reinforce mullions with aluminum sections if required. Secure aluminum sections with adequate anchors to structure. .5 Jointing and intersections of metals shall be accurately cut, fitted to a tolerance of 1/16" in true planes with adequate concealed fastenings and sealed. .6 All gaskets forming weather seals and air seals shall be formed into complete frames with vulcanized corner joints. .7 All gaskets shall be free from all contact and migration stain and compatible with all substrates, sealants and finishes with which they contact. Project No. 9654 Issue March 7, 1997 136 ATTACHMENT "F" CURTAIN WALL SECTION 8900 PAGE 19 -------------------------------------------------------------------------------- .8 Perform fitting and assembly of component parts in shop; units which cannot be permanently shop assembled shall be fitted, assembled, marked and disassembled to assure proper fitting in the field. Identify field assembly joints on shop drawings. .9 Fabricate all devices required for erection and adequate anchorage and attachment, including items required to be built into or attached to the wall panels or structure for the support of the work. .10 Provide inconspicuous, baffled weep holes to properly vent, pressure equalized and drain system cavities to exterior. .11 All exposed aluminum surfaces of frame sections, sill and cut-offs shall have matching finish in colour selected. .12 Fabricate glazing recess of sufficient depth to cover glass edge-seal, 3/4" minimum. .13 Air seal junctions of all horizontal and vertical aluminum members with joint tape and sealant. .14 Use two part polysulfide adhesive to bond copper to painted aluminum extrusions for exterior caps. .15 Co-ordinate with Security Section. Provide cutouts in frame for security devices at opening windows and doors including electric locks at doors. Provide conduit within frame (supplied by Division 16000)
Sample 1
FABRICATION, GENERAL. A. Provide complete stair assemblies, including metal framing, hangers, struts, railings, clips, brackets, bearing plates, and other components necessary to support and anchor stairs and platforms on supporting structure. 1. Join components by welding unless otherwise indicated. 2. Use connections that maintain structural value of joined pieces. 3. Fabricate treads and platforms of exterior stairs so finished walking surfaces slope to drain. B. Preassembled Stairs: Assemble stairs in shop to greatest extent possible. Disassemble units only as necessary for shipping and handling limitations. C. Cut, drill, and punch metals cleanly and accurately. Remove burrs and ease edges. Remove sharp or rough areas on exposed surfaces. D. Form bent-metal corners to smallest radius possible without impairing work. E. Weld connections to comply with the following: 1. Use materials and methods that minimize distortion and develop strength and corrosion resistance of base metals. 2. Obtain fusion without undercut or overlap. 3. Remove welding flux immediately. 4. Weld exposed corners and seams continuously unless otherwise indicated. 5. At exposed connections, finish exposed welds to comply with NOMMA's "Voluntary Joint Finish Standards" for Type 4 welds: good quality, uniform undressed weld with minimal splatter. F. Form exposed connections with hairline joints, flush and smooth, using concealed fasteners where possible. Locate joints where least conspicuous. G. Fabricate joints that will be exposed to weather in a manner to exclude water. Provide weep holes where water may accumulate.
Sample 1
FABRICATION, GENERAL. A. Shop Assembly: Preassemble items in shop to greatest extent possible to minimize field splicing and assembly. Disassemble units only as necessary for shipping and handling limitations. Use connections that maintain structural value of joined pieces. Clearly mark units for reassembly and coordinated installation. X. Xxxxx and punch metals cleanly and accurately. Remove burrs. C. Ease exposed edges to a radius of approximately 1/32 inch, unless otherwise indicated. Form bent-metal corners to smallest radius possible without causing grain separation or otherwise impairing work. D. Weld corners and seams continuously to comply with the following: 1. Use materials and methods that minimize distortion and develop strength and corrosion resistance of base metals. 2. Obtain fusion without undercut or overlap. 3. Remove welding flux immediately. 4. At exposed connections, finish exposed welds and surfaces smooth and blended so no roughness shows after finishing and contour of welded surface matches that of adjacent surface.
Sample 1
FABRICATION, GENERAL. A. Shop Assembly: Preassemble items in shop to greatest extent possible to minimize field splicing and assembly. Disassemble units only as necessary for shipping and handling limitations. Use connections that maintain structural value of joined pieces. Clearly mark units for reassembly and coordinated installation. B. Provide access door assemblies manufactured as integral units ready for installation. C. Fabricate and prepare products required to be galvanized in accordance with recommendations of AGA. D. Provide material that is free from mill scale, flake rust and mill pitting. E. Cut, reinforce, drill and tap metal fabrications as indicated to receive finish hardware, screws, and similar items. Provide plates welded on for mounting hardware. X. Xxxxx and punch metals cleanly and accurately. Remove burrs. G. Form exposed connections with hairline joints, flush and smooth, using concealed fasteners whenever possible. Use exposed fasteners of type indicated or, if not indicated, Xxxxxxxx flat- head (countersunk) screws or bolts. Locate joints where least conspicuous. H. Ease exposed edges to a radius of approximately 1/32 inch, unless otherwise indicated. Form bent-metal corners to smallest radius possible without causing grain separation or otherwise impairing work. I. Provide for anchorage of type indicated; coordinate with supporting structure. Fabricate and space anchoring devices to secure metal fabrications rigidly in place and to support indicated loads. J. Where miscellaneous access openings, with exception of gratings, occur in finished floor areas, include stainless steel edge rims of depth to accommodate floor finishing materials. K. Welding corners and seams continuously to comply with the following: 1. Use materials and methods that minimize distortion and develop strength and corrosion resistance of base metals. 2. Obtain fusion without undercut or overlap. 3. Remove welding flux immediately. 4. At exposed connections, finish exposed welds and surfaces smooth and blended so no roughness shows after finishing and contour of welded surface matches that of adjacent surface. L. Fabricate joints that will be exposed to weather in a manner to exclude water, or provide weep holes where water may accumulate. M. Form exposed work true to line and level with accurate angles and surfaces and straight sharp edges. N. Remove sharp or rough areas on exposed traffic surfaces. O. Painting: Shop paint (prime) before shipment. Phosphatize galvanized surfaces ...
Sample 1
FABRICATION, GENERAL. A. General:
Sample 1
AutoNDA by SimpleDocs

Related to FABRICATION, GENERAL

  • Fabrication Making up data or results and recording or reporting them.

  • Durable Medical Equipment (DME), Medical Supplies, Prosthetic Devices, Enteral Formula or Food, and Hair Prosthesis (Wigs) This plan covers durable medical equipment and supplies, prosthetic devices and enteral formula or food as described in this section. DME is equipment which: • can withstand repeated use; • is primarily and customarily used to serve a medical purpose; • is not useful to a person in the absence of an illness or injury; and • is for use in the home. DME includes supplies necessary for the effective use of the equipment. This plan covers the following DME: • wheelchairs, hospital beds, and other DME items used only for medical treatment; and • replacement of purchased equipment which is needed due to a change in your medical condition or if the device is not functional, no longer under warranty, or cannot be repaired. DME may be classified as a rental item or a purchased item. In most cases, this plan only pays for a rental DME up to our allowance for a purchased DME. Repairs and supplies for rental DME are included in the rental allowance. Medical supplies are consumable supplies that are disposable and not intended for re- use. Medical supplies require an order by a physician and must be essential for the care or treatment of an illness, injury, or congenital defect. Covered medical supplies include: • essential accessories such as hoses, tubes and mouthpieces for use with medically necessary DME (these accessories are included as part of the rental allowance for rented DME); • catheters, colostomy and ileostomy supplies, irrigation trays and surgical dressings; and • respiratory therapy equipment. This plan covers diabetic equipment and supplies for the treatment of diabetes in accordance with R.I. General Law §27-20-30. Covered diabetic equipment and supplies include: • therapeutic or molded shoes and inserts for custom-molded shoes for the prevention of amputation; • blood glucose monitors including those with special features for the legally blind, external insulin infusion pumps and accessories, insulin infusion devices and injection aids; and • lancets and test strips for glucose monitors including those with special features for the legally blind, and infusion sets for external insulin pumps. The amount you pay differs based on whether the equipment and supplies are bought from a durable medical equipment provider or from a pharmacy. See the Summary of Pharmacy Benefits and the Summary of Medical Benefits for details. Coverage for some diabetic equipment and supplies may only be available from either a DME provider or from a pharmacy. Visit our website to determine if this is applicable or call our Customer Service Department. Prosthetic devices replace or substitute all or part of an internal body part, including contiguous tissue, or replace all or part of the function of a permanently inoperative or malfunctioning body part and alleviate functional loss or impairment due to an illness, injury or congenital defect. Prosthetic devices do not include dental prosthetics. This plan covers the following prosthetic devices as required under R.I. General Law § 27-20-52: • prosthetic appliances such as artificial limbs, breasts, larynxes and eyes; • replacement or adjustment of prosthetic appliances if there is a change in your medical condition or if the device is not functional, no longer under warranty and cannot be repaired; • devices, accessories, batteries and supplies necessary for prosthetic devices; • orthopedic braces except corrective shoes and orthotic devices used in connection with footwear; and • breast prosthesis following a mastectomy, in accordance with the Women’s Health and Cancer Rights Act of 1998 and R.I. General Law 27-20-29. The prosthetic device must be ordered or provided by a physician, or by a provider under the direction of a physician. When you are prescribed a prosthetic device as an inpatient and it is billed by a provider other than the hospital where you are an inpatient, the outpatient benefit limit will apply. Enteral formula or food is nutrition that is absorbed through the intestinal tract, whether delivered through a feeding tube or taken orally. Enteral nutrition is covered when it is the sole source of nutrition and prescribed by the physician for home use. In accordance with R.I. General Law §27-20-56, this plan covers enteral formula taken orally for the treatment of: • malabsorption caused by Crohn’s Disease; • ulcerative colitis; • gastroesophageal reflux; • chronic intestinal pseudo obstruction; and • inherited diseases of amino acids and organic acids. Food products modified to be low protein are covered for the treatment of inherited diseases of amino acids and organic acids. Preauthorization may be required. The amount that you pay may differ depending on whether the nutrition is delivered through a feeding tube or taken orally. When enteral formula is delivered through a feeding tube, associated supplies are also covered. This plan covers hair prosthetics (wigs) worn for hair loss suffered as a result of cancer treatment in accordance with R.I. General Law § 27-20-54 and subject to the benefit limit and copayment listed in the Summary of Medical Benefits. This plan will reimburse the lesser of the provider’s charge or the benefit limit shown in the Summary of Medical Benefits. If the provider’s charge is more than the benefit limit, you are responsible for paying any difference. This plan covers Early Intervention Services in accordance with R.I. General Law §27- 20-50. Early Intervention Services are educational, developmental, health, and social services provided to children from birth to thirty-six (36) months. The child must be certified by the Rhode Island Department of Human Services (DHS) to enroll in an approved Early Intervention Services program. Services must be provided by a licensed Early Intervention provider and rendered to a Rhode Island resident. Members not living in Rhode Island may seek services from the state in which they reside; however, those services are not covered under this plan. Early Intervention Services as defined by DHS include but are not limited to the following: • speech and language therapy; • physical and occupational therapy; • evaluation; • case management; • nutrition; • service plan development and review; • nursing services; and • assistive technology services and devices.

  • Computer Equipment Recycling Program If this Contract is for the purchase or lease of computer equipment, then Contractor certifies that it is in compliance with Subchapter Y, Chapter 361 of the Texas Health and Safety Code related to the Computer Equipment Recycling Program and the Texas Commission on Environmental Quality rules in 30 TAC Chapter 328.

  • Manufacturing (a) The Supplier shall without limitation be responsible, at no additional cost to the Purchaser, for: sourcing and procuring all raw materials for the Products; obtaining all necessary approvals, permits and licenses for the manufacturing of the Products; providing sufficient qualified staff and workers to perform the obligations under this Purchase Agreement; implementing and maintaining effective inventory and production control procedures with respect to the Products; and handling other matters as reasonably requested by the Purchaser from time to time. (b) The Supplier shall not change any process, material, component, packaging or manufacturing location without the Purchaser’s express prior written approval.

  • Television Equipment Recycling Program If this Contract is for the purchase or lease of covered television equipment, then Contractor certifies that it is compliance with Subchapter Z, Chapter 361 of the Texas Health and Safety Code related to the Television Equipment Recycling Program.

  • Equipment Cleaning (a) Areas, known by Forest Service prior to timber sale advertisement, that are infested with invasive species of concern are shown on Sale Area Map. A current list of invasive species of concern and a map showing the extent of known infestations is available at the Forest Supervisor’s Office. For purposes of this provision, “Off-Road Equipment” includes all logging and construction machinery, except for log trucks, chip vans, service vehicles, water trucks, pickup trucks, cars, and similar vehicles.

  • General specifications For the purpose of this Regulation, the vehicle shall fulfil the following requirements:

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CSTC chooses to subtend a Verizon access Tandem, CSTC’s NPA/NXX must be assigned by CSTC to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG. 9.2.2 CSTC shall establish Access Toll Connecting Trunks pursuant to applicable access Tariffs by which it will provide Switched Exchange Access Services to Interexchange Carriers to enable such Interexchange Carriers to originate and terminate traffic to and from CSTC’s Customers. 9.2.3 The Access Toll Connecting Trunks shall be two-way trunks. Such trunks shall connect the End Office CSTC utilizes to provide Telephone Exchange Service and Switched Exchange Access to its Customers in a given LATA to the access Tandem(s) Verizon utilizes to provide Exchange Access in such LATA. 9.2.4 Access Toll Connecting Trunks shall be used solely for the transmission and routing of Exchange Access to allow CSTC’s Customers to connect to or be connected to the interexchange trunks of any Interexchange Carrier which is connected to a Verizon access Tandem.

  • Equipment Procurement If responsibility for construction of the Connecting Transmission Owner’s Attachment Facilities or System Upgrade Facilities or System Deliverability Upgrades is to be borne by the Connecting Transmission Owner, then the Connecting Transmission Owner shall commence design of the Connecting Transmission Owner’s Attachment Facilities or System Upgrade Facilities or System Deliverability Upgrades and procure necessary equipment as soon as practicable after all of the following conditions are satisfied, unless the Developer and Connecting Transmission Owner otherwise agree in writing: 5.5.1 NYISO and Connecting Transmission Owner have completed the Interconnection Facilities Study pursuant to the Interconnection Facilities Study Agreement; 5.5.2 The NYISO has completed the required cost allocation analyses, and Developer has accepted his share of the costs for necessary System Upgrade Facilities and System Deliverability Upgrades in accordance with the provisions of Attachment S of the NYISO OATT; 5.5.3 The Connecting Transmission Owner has received written authorization to proceed with design and procurement from the Developer by the date specified in Appendix B hereto; and 5.5.4 The Developer has provided security to the Connecting Transmission Owner in accordance with Article 11.5 by the dates specified in Appendix B hereto.

  • Innovative Scheduling Schedules which are inconsistent with the Collective Agreement provisions may be developed in order to improve quality of working life, support continuity of resident care, ensure adequate staffing resources, and support cost-efficiency. The parties agree that such innovative schedules may be determined locally by the Home and the Union subject to the following principles: (a) Such schedules shall be established by mutual agreement of the Home and the Union; (b) These schedules may pertain to full-time and/or part-time employees; (c) The introduction of such schedules and trial periods, if any, shall be determined by the local parties. Such schedules may be discontinued by either party with notice as determined through local negotiations; (d) Upon written agreement of the Home and the Union, the parties may agree to amend collective agreement provisions to accommodate any innovative unit schedules; (e) It is understood and agreed that these arrangements are based on individual circumstances and each agreement is made on a without prejudice or precedent basis. (f) It is understood and agreed that these arrangements can be utilized for temporary job postings for seasonal coverage (e.g. weekend workers, etc.).

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!