Gas Metering Sample Clauses

Gas Metering. 12.1. Gas quantity shall be measured in cubic metres (m3). 12.2. Gas quantity shall be calculated in cubic meters under standard conditions when the absolute pressure is P = 1.01325 bar and temperature T = 20°C, calorific value of gas quantity shall be calculated in kilowatt hours respectively (kWh). 12.3. When the TSO transmits gas to the delivery location where the natural gas system of the System User’s consumer begins, or when the TSO delivers gas to the delivery location where the consumer natural gas system begins and the consumer has an effective contract with the System User for the sale and purchase of natural gas and for provision of services: 12.3.1. Gas metering systems (measurement instrument) shall be installed and operated in accordance with the requirements of applicable legislation, normative documents and equipment manufacturers. 12.3.2. The maximum and minimum allowable gas flow (rate) permitted in the gas metering system(s) (gas flow (debit) per meter under standard conditions (Qmax and Qmin) and gas pressure at a particular delivery location of the System User shall be indicated in Appendix 1 to the Contract. 12.3.3. Gas flow cannot exceed the maximum allowable gas flow permitted in the gas metering system (measurement instrument) expressed as Qmax or be lower than Qmin. 12.3.4. Gas metering systems (measurement instrument) shall be sealed to prevent interference with their operation without taking off the seals. 12.3.5. On detection of failure, imbalance in the gas metering system (measurement instrument) and in the event of metrological verification of the system gas quantity shall be calculated from the start day of failure or imbalance of the gas metering system (measurement instruments) until the failure or imbalance is eliminated, or for the duration of metrological verification gas consumption shall be calculated based on the average daily gas consumption for the last 3 days or using some other method id agreed between the Parties. 12.3.6. If due to the System User the flow of gas consumed does not come close to the minimum allowable gas flow Qmin specified in Appendix 1 of the Contract, gas flow shall be calculated as the minimum allowable gas flow Qmin specified n Appendix 1 to the Contract. 12.3.7. Gas quantities delivered to the System User at these delivery locations shall be determined by readings of the gas metering systems (measurement instruments). The TSO shall calculate gas quantities over the reporting period based o...
Sample 1
AutoNDA by SimpleDocs
Gas Metering. (a) Gas delivered by Buyer to the Gas Delivery Point shall be measured by the Gas Meter at the Gas Delivery Point. The Gas Transporter shall own, operate, maintain and test the Gas Meter located at the Gas Delivery Point. Seller shall coordinate with the Gas Transporter and Buyer with respect to maintenance and testing of the Gas Meter consistent with the Gas Transmission Service Agreement and
Sample 1
Gas Metering. (a) Gas delivered by Buyer to the Gas Delivery Point shall be measured by the Gas Meter at the Gas Delivery Point. The Gas Transporter shall own, operate, maintain and test the Gas Meter located at the Gas Delivery Point. Seller shall coordinate with the Gas Transporter and Buyer with respect to maintenance and testing of the Gas Meter consistent with the Gas Transmission Service Agreement and Good Industry Practice. The Gas Meter located at the Gas Delivery Point will measure the Gas consumed by the entire Facility rather than individual Units. (b) Notwithstanding the foregoing, Seller may, at its sole cost and expense, cause Gas meters to be installed at each Non-RMR Unit that satisfy the requirements outlined in Schedule C, Part 1, A(2)(a), of the RMR Agreements (“Non-RMR Unit Gas Meters”), In such event, Seller shall coordinate with the Gas Transporter and Buyer with respect to maintenance and testing of the Non-RMR Unit Gas Meters consistent with the Gas Transmission Service Agreement and Good Industry Practice, and the Non-RMR Unit Gas Meters will measure the Gas consumed by the Non-RMR Units.
Sample 1
Gas Metering. At all times during the Delivery Term, Gas delivered by Buyer to Seller shall be metered at the GDP, in all cases on a continuous real time basis. Seller shall be responsible for the installation, maintenance, testing, and calibration of the Gas Metering Equipment (to the extent not otherwise installed, maintained, tested, and calibrated by Buyer). Buyer shall have the right to receive data in electronic form in real time on a continuous basis from the GDP, and Seller shall undertake to install one Gas meter which is capable of providing such data to Buyer’s reasonable satisfaction. Seller shall bear all costs and expenses of installing, maintaining and testing all Gas Metering Equipment. Buyer shall bear the cost of the delivery to Buyer of data from such meters.
Sample 1
Gas Metering. 8.8.1 To the maximum extent possible and subject to the capabilities of the Gas Metering Equipment, Gas delivered by DMT hereunder shall be measured at the Gas Delivery Point on a continuous real-time basis. The Gas Metering Equipment shall be used to determine the quantity of Gas delivered at the Gas Delivery Point. Facility Metering Equipment may be installed at the Facility to monitor consumption (on a continuous real time basis) of Gas at the Facility. 8.8.2 Southern shall be responsible for performing, or causing to be performed, and shall bear all costs and expenses of the installation, maintenance, repair, testing and initial calibration of the Gas Metering Equipment and the Facility Metering Equipment (to the extent not otherwise installed, maintained, tested and calibrated by the Transporter or other third party). DMT shall reimburse Southern for up to [redacted] in costs and expenses incurred by Southern to install the Facility Metering Equipment within [redacted] after receipt of an invoice from Southern for the same.
Sample 1
Gas Metering 
Sample 1

Related to Gas Metering

  • Metering The Interconnection Customer shall be responsible for the Connecting Transmission Owner’s reasonable and necessary cost for the purchase, installation, operation, maintenance, testing, repair, and replacement of metering and data acquisition equipment specified in Attachments 2 and 3 of this Agreement. The Interconnection Customer’s metering (and data acquisition, as required) equipment shall conform to applicable industry rules and Operating Requirements.

  • Interconnection 2.1 This section applies to linking with suppliers providing public telecommunications transport networks or services in order to allow the users of one supplier to communicate with users of another supplier and to access services provided by another supplier, where specific commitments are undertaken.

  • Gas If Customer has selected a Gas Fixed Rate, Customer’s Price will be based on the Fixed Rate(s), plus the Administration Charge, set forth in the Application, which includes RITERATE ENERGY’s compressor fuel and transportation charges, administrative and transaction costs and the Gas Balancing Amount and any Regulatory Charges (defined below).

  • One-Way Interconnection Trunks 2.3.1 Where the Parties use One-Way Interconnection Trunks for the delivery of traffic from Onvoy to Frontier, Onvoy, at Xxxxx’s own expense, shall: 2.3.1.1 provide its own facilities for delivery of the traffic to the technically feasible Point(s) of Interconnection on Frontier’s network in a LATA; and/or 2.3.1.2 obtain transport for delivery of the traffic to the technically feasible Point(s) of Interconnection on Frontier’s network in a LATA (a) from a third party, or, (b) if Frontier offers such transport pursuant to a Frontier access Tariff, from Frontier. 2.3.2 For each Tandem or End Office One-Way Interconnection Trunk group for delivery of traffic from Onvoy to Frontier with a utilization level of less than sixty percent (60%) for final trunk groups and eighty-five percent (85%) for high usage trunk groups, unless the Parties agree otherwise, Onvoy will promptly submit ASRs to disconnect a sufficient number of Interconnection Trunks to attain a utilization level of approximately sixty percent (60%) for all final trunk groups and eighty-five percent (85%) for all high usage trunk groups. In the event Onvoy fails to submit an ASR to disconnect One-Way Interconnection Trunks as required by this Section, Frontier may disconnect the excess Interconnection Trunks or bill (and Onvoy shall pay) for the excess Interconnection Trunks at the rates set forth in the Pricing Attachment. 2.3.3 Where the Parties use One-Way Interconnection Trunks for the delivery of traffic from Frontier to Onvoy, Frontier, at Frontier’s own expense, shall provide its own facilities for delivery of the traffic to the technically feasible Point(s) of Interconnection on Frontier’s network in a LATA.

  • Points of Interconnection and Trunk Types 2.1 Point(s) of Interconnection. 2.1.1 Each Party, at its own expense, shall provide transport facilities to the technically feasible Point(s) of Interconnection on Verizon’s network in a LATA selected by PNG.

  • Interconnection Service Interconnection Service allows the Interconnection Customer to connect the Large Generating Facility to the Participating TO’s Transmission System and be eligible to deliver the Large Generating Facility’s output using the available capacity of the CAISO Controlled Grid. To the extent the Interconnection Customer wants to receive Interconnection Service, the Participating TO shall construct facilities identified in Appendices A and C that the Participating TO is responsible to construct.

  • Infrastructure Infrastructure serves as the foundation and building blocks of an integrated IT solution. It is the hardware which supports Application Services (C.3.2) and IT Management Services (C.3.3); the software and services which enable that hardware to function; and the hardware, software, and services which allow for secure communication and interoperability between all business and application service components. Infrastructure services facilitate the development and maintenance of critical IT infrastructures required to support Federal government business operations. This section includes the technical framework components that make up integrated IT solutions. One or any combination of these components may be used to deliver IT solutions intended to perform a wide array of functions which allow agencies to deliver services to their customers (or users), whether internal or external, in an efficient and effective manner. Infrastructure includes hardware, software, licensing, technical support, and warranty services from third party sources, as well as technological refreshment and enhancements for that hardware and software. This section is aligned with the FEA/DoDEA Technical Reference Model (TRM) which describes these components using a vocabulary that is common throughout the entire Federal government. A detailed review of the TRM is provided in Section J, Attachment 5. Infrastructure includes complete life cycle support for all hardware, software, and services represented above, including planning, analysis, research and development, design, development, integration and testing, implementation, operations and maintenance, information assurance, and final disposition of these components. The services also include administration and help desk functions necessary to support the IT infrastructure (e.g., desktop support, network administration). Infrastructure components of an integrated IT solution can be categorized as follows:

  • Pipelines Developer shall have no interest in the pipeline gathering system, which gathering system shall remain the sole property of Operator or its Affiliates and shall be maintained at their sole cost and expense.

  • Network Interconnection Architecture Each Party will plan, design, construct and maintain the facilities within their respective systems as are necessary and proper for the provision of traffic covered by this Agreement. These facilities include but are not limited to, a sufficient number of trunks to the point of interconnection with the tandem company, and sufficient interoffice and interexchange facilities and trunks between its own central offices to adequately handle traffic between all central offices within the service areas at a P.01 grade of service or better. The provisioning and engineering of such services and facilities will comply with generally accepted industry methods and practices, and will observe the rules and regulations of the lawfully established tariffs applicable to the services provided.

  • Methods of Interconnection The Parties will negotiate the facilities arrangement used to interconnect their respective networks. CLEC shall establish at least one (1) physical Point of Interconnection in CenturyLink territory in each LATA CLEC has local End User Customers. CLEC represents and warrants that it is serving End User Customers physically located within each local calling area for which it wishes to exchange traffic within CenturyLink territory. The Parties shall establish, through negotiations, at least one (1) of the following Interconnection arrangements, at any Technically Feasible point: (1) a DS1 or DS3 CenturyLink-provided facility; (2) Collocation; (3) negotiated Mid-Span Meet POI facilities; or (4) other Technically Feasible methods of Interconnection via the Bona Fide Request (BFR) process unless a particular arrangement has been previously provided to a third party, or is offered by CenturyLink as a product. 7.1.2.1 CenturyLink-provided Facility. Interconnection may be accomplished through the provision of a DS1 or DS3 Entrance Facility of CLEC's determination. An Entrance Facility extends from the CenturyLink Serving Wire Center to CLEC's Switch location or any Technically Feasible POI chosen by CLEC. CenturyLink-provided Entrance Facilities may not extend beyond the area served by the CenturyLink Serving Wire Center. The rates for CenturyLink-provided Entrance Facilities are provided in Exhibit A. CenturyLink's private line transport service is available as an alternative to CenturyLink-provided Entrance Facilities, when CLEC uses such private line transport service for multiple services. Entrance Facilities may not be used for Interconnection with Unbundled Network Elements. 7.1.2.2 Collocation. Interconnection may be accomplished through the Collocation arrangements offered by CenturyLink. The terms and conditions under which Collocation will be available are described in Section 8 of this Agreement. 7.1.2.2.1 Expanded Interconnection Channel Termination (EICT) provides the communication path that actually connects the physical space or in the case of virtual collocation, the designated equipment to CenturyLink's direct trunked transport and must be ordered to provision LIS to a collocation. 7.1.2.3 Mid-Span Meet POI. A Mid-Span Meet POI is a negotiated Point of Interface, limited to the Interconnection of facilities between the CenturyLink Serving Wire Center location and the location of the CLEC switch or other equipment located within the area served by the CenturyLink Serving Wire Center. The actual physical Point of Interface and facilities used will be subject to negotiations between the Parties. Each Party will be responsible for its portion of the build to the Mid-Span Meet POI. The Mid-Span Meet POI will be used exclusively as an Interconnection facility and cannot be used for other purposes such as Unbundled Network Elements or Access Services.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!