Measurements and Dimensions. Before ordering material or doing work that is dependent upon coordination with building conditions, the Contractor shall verify all dimensions, elevations, grades, and pitch by taking measurements at the building and shall be responsible for the correctness of same. Any discrepancies between the drawings and/or specifications and the existing conditions shall be referred to the Design Professional for additional instructions before any work affected thereby is begun.
Measurements and Dimensions. Rain Water, Surface Water, and Back-up.
Measurements and Dimensions. Before ordering material or doing work that is dependent upon coordination with building conditions, the CM/GC shall verify all dimensions, elevations, grades, and pitch by taking measurements at the building and shall be responsible for the correctness of same. Any discrepancies between the drawings and/or specifications and the existing conditions shall be referred to the Design Professional for additional instructions before any work affected thereby is begun. Rain Water, Surface Water, and Back-up. The CM/GC shall protect all Work, including but not limited to, excavations and trenches, from rainwater, surface water, and back up of drains and sewers. The CM/GC shall furnish all labor, pumps, shoring, enclosures, and equipment necessary to protect and to keep the Work free of water.
Measurements and Dimensions. Without limiting clause 8.14: the Contractor must obtain and check all relevant measurements and dimensions on Site before proceeding with the Contractor's Activities; the layout of plant, equipment, ductwork, pipework and cabling shown in the Works Description (if any) is to be taken as diagrammatic only and all measurements and dimension information concerning the Site required to carry out the Contractor's Activities must be obtained and checked by the Contractor; and to the extent permitted by law, the Contractor will not be entitled to make (nor will the Commonwealth be liable upon) any Claim arising out of or in connection with the Contractor's failure to obtain and check measurements and dimension information concerning the Site as required by clause 8.28.
Measurements and Dimensions. Before ordering material or doing work that is dependent upon coordination with building conditions, the CM/GC shall verify all dimensions, elevations, grades, and pitch by taking measurements at the building and shall be responsible for the correctness of same. Any discrepancies between the drawings and/or specifications and the existing conditions shall be referred to the Design Professional for additional instructions before any work affected thereby is begun.
Measurements and Dimensions. Without limiting clause 6.2: the Contractor must obtain and check all relevant measurements and dimensions on Site before proceeding with the Contractor's Activities; and the layout of plant, equipment, ductwork, pipework and cabling shown in the Works Description (if any) is to be taken as diagrammatic only and all measurements and dimension information concerning the Site required to carry out the Contractor's Activities must be obtained and checked by the Contractor. To the extent permitted by law, the Contractor will not be entitled to make (nor will the Commonwealth be liable upon) any claim (whether under the Contract or otherwise at law or in equity) arising out of or in connection with the Contractor's failure to obtain and check measurements and dimension information concerning the Site as required by this clause 6.12.
Measurements and Dimensions. Without limiting clause 6.2: the Subcontractor must obtain and check all relevant measurements and dimensions on Site before proceeding with the Subcontractor's Activities; and the layout of plant, equipment, ductwork, pipework and cabling shown in the Subcontract Works Description (if any) is to be taken as diagrammatic only and all measurements and dimension information concerning the Site required to carry out the Subcontractor's Activities must be obtained and checked by the Subcontractor. To the extent permitted by law, the Subcontractor will not be entitled to make (nor will the Contractor be liable upon) any claim (whether under the Subcontract or otherwise at law or in equity) arising out of or in connection with the Subcontractor's failure to obtain and check measurements and dimension information concerning the Site as required by this clause 6.12.
Measurements and Dimensions. Without limiting clause 6.2: the Contractor must obtain and check all relevant measurements and dimensions on Site before proceeding with the Contractor's Activities; the layout of plant, equipment, ductwork, pipework and cabling shown in the Design Documents (if any) is to be taken as diagrammatic only and all measurements and dimension information concerning the Site required to carry out the Contractor's Activities must be obtained and checked by the Contractor; and the Principal will not be liable upon any claim by the Contractor resulting from the Contractor's failure to obtain and check measurements and dimension information concerning the Site as required by this clause 6.12.
Measurements and Dimensions. Before ordering material or doing work that is dependent upon coordination with building conditions, the CMR shall verify all dimensions, elevations, grades, and pitch by taking measurements at the building and shall be responsible for the correctness of same. Any discrepancies between the drawings and/or specifications and the existing conditions shall be referred to the Design Professional for additional instructions before any work affected thereby is begun.
Measurements and Dimensions. Unless expressly stated to the contrary in the Contract or directed by the Contract Administrator: the Consultant must obtain and check all relevant measurements and dimensions on the Site before proceeding with the Services; the layout of plant, equipment, duct work, pipework and cabling shown in the Brief (if any) is to be taken as diagrammatic only and all measurements and dimensions information concerning the Site required to carry out the Services must be obtained and checked by the Consultant; and to the extent permitted by law, the Consultant will not be entitled to make (nor will the Commonwealth be liable upon) any Claim arising out of or in connection with the Consultant's failure to obtain and check measurements and dimension information concerning the Site as required by clause 6.13.
