We use cookies on our site to analyze traffic, enhance your experience, and provide you with tailored content.

For more information visit our privacy policy.

Other Additives Sample Clauses

Other Additives. The additives are any other materials that are added to the emulsion mix or to any of the component materials to provide the specified properties. The additives shall be supplied by the emulsion manufacturer to provide control of the set time in the field. The Contractor shall submit a mix design certified by the latex modified emulsion manufacturer and present certified test results for the Engineer's approval. Compatibility of the aggregate and latex modified CSS-1h or CQS-1h shall be certified. The job mix formula shall provide a minimum Xxxxxxxx stability of 1,800 pounds and a flow of 6 to 16 units when tested according to modified ASTM procedures. Aggregate used in the job mix formula shall be of the material proposed by the Contractor for use on the project. Submit mix design to the Materials and Tests Unit for approval. The mix design shall conform to the International Slurry Surfacing Association’s ISSA A143, Section 5.2. The gradation of the aggregate shall be in accordance with the following: The gradation of the aggregate stockpile shall not vary by more than the stockpile tolerance from the mix design gradation (indicated in the table above) while also remaining within the specification gradation band. The percentage of aggregate passing any 2 successive sieves shall not change from one end of the specified range to the other end. The aggregate will be accepted at the job location or stockpile based on 5 gradation tests sampled according to AASHTO T 2. If the average of the 5 tests is within the stockpile tolerance from the mix design gradation, the material will be accepted. If the average of those test results is out of specification or tolerance, the Contractor will be given the choice to either remove the material or blend additional aggregate with the stockpile material to bring it into compliance. Materials used in blending shall meet the required aggregate quality test specifications in Section 1012 of the 2012 Standard Specifications before blending and shall be blended in a manner to produce a consistent gradation. Aggregate blending may require a new mix design. Screening shall be required at the stockpile if there are any problems created by oversized materials in the mix. Type II aggregate gradation is used to fill surface voids, address surface distresses, seal and provide a durable wearing surface. Type III aggregate gradation provides maximum skid resistance and an improved wearing surface. This type of microsurfacing is appropri...
Other AdditivesThe Contractor may use other additives to provide control of the break/set time in the field. Ensure that the type of additive is specified in the mix design.

Related to Other Additives

  • Transporting Students 1. Employees shall not transport students except in accordance with School Board rules. The Board shall adopt a school board policy outlining the teacher’s and the Board’s responsibilities and liabilities. Said policy shall be included in all school handbooks beginning with the 2004-05 school year. 2. Teachers will not be required to transport pupils to and from activities which take place away from the school grounds.

  • Samples The Contractor shall submit the following samples of Materials and relevant information to the Authority’s Engineer for pre-construction review: (a) manufacturer's test reports and standard samples of manufactured Materials; and (b) samples of such other Materials as the Authority’s Engineer may require.

  • Materials of Environmental Concern have not been transported or disposed of from the Properties in violation of, or in a manner or to a location that could give rise to liability under, any Environmental Law, nor have any Materials of Environmental Concern been generated, treated, stored or disposed of at, on or under any of the Properties in violation of, or in a manner that could give rise to liability under, any applicable Environmental Law;

  • Gas If Customer has selected a Gas Fixed Rate, Customer’s Price will be based on the Fixed Rate(s), plus the Administration Charge, set forth in the Application, which includes RITERATE ENERGY’s compressor fuel and transportation charges, administrative and transaction costs and the Gas Balancing Amount and any Regulatory Charges (defined below).

  • RE-WEIGHING PRODUCT Deliveries are subject to re- weighing at the point of destination by the Authorized User. If shrinkage occurs which exceeds that normally allowable in the trade, the Authorized User shall have the option to require delivery of the difference in quantity or to reduce the payment accordingly. Such option shall be exercised in writing by the Authorized User.

  • Products Products available under this Contract are limited to Software, including Software as a Service, products and related products as specified in Appendix C, Pricing Index. Vendor may incorporate changes to their product offering; however, any changes must be within the scope of products awarded based on the posting described in Section 1.B above. Vendor may not add a manufacturer’s product line which was not included in the Vendor’s response to the solicitation described in Section 1.B above.

  • Containers The marine and intermodal cargo containers either owned or leased by the Borrower and employed by the Borrower in the conduct of its business, including, without limitation, refrigerated, dry van, tank, open top and flat rack containers and refrigeration units and generator sets associated therewith, but excluding any chassis for such containers.

  • REPAIRED OR REPLACED PARTS / COMPONENTS Where the Contractor is required to repair, replace or substitute Product or parts or components of the Product under the Contract, the repaired, replaced or substituted Products shall be subject to all terms and conditions for new parts and components set forth in the Contract including Warranties, as set forth in the Additional Warranties Clause herein. Replaced or repaired Product or parts and components of such Product shall be new and shall, if available, be replaced by the original manufacturer’s component or part. Remanufactured parts or components meeting new Product standards may be permitted by the Commissioner or Authorized User. Before installation, all proposed substitutes for the original manufacturer’s installed parts or components must be approved by the Authorized User. The part or component shall be equal to or of better quality than the original part or component being replaced.

  • Passengers THE CARRIER shall be liable for damages resulting from death or bodily injury to a Passenger by the sole reason that the act which caused the damages took place on board the aircraft or during boarding or deboarding the aircraft.

  • Raw Materials A. Catalent shall be responsible for procuring, inspecting and releasing adequate Raw Materials as necessary to meet the Firm Commitment, unless otherwise agreed to by the parties in writing. Unless a particular Raw Material can be replaced with the same raw material from another supplier, Catalent shall not be liable for any delay in delivery of Product or Packaged Product if (1) Catalent is unable to obtain, in a timely manner, a particular Raw Material necessary to Process or Package the Product, (2) Catalent placed orders for such Raw Materials promptly following receipt of Client’s Firm Commitment and (3) such delay did not result, in whole or in part, from the negligence or willful misconduct of Catalent. B. In certain instances, Client may require a specific supplier, manufacturer or vendor (“Supplier”) to be used for a Raw Material. In such an event, (i) such Supplier will be identified in the Specifications, (ii) Client shall be responsible for the timeliness, quantity and quality of supply of Raw Materials from such Supplier, subject to Catalent’s compliance with its obligations set forth in Section 3.2A, (iii) Catalent shall not be liable for any defects in Raw Materials or in Packaging or Packaged Product as a result of such defective Raw Materials from such Supplier, or in Product or Packaged Product as a result of such defective Raw Materials, unless Catalent failed to properly perform any testing required by the Specifications, and (iv) the Raw Materials from such Supplier shall be deemed, for purposes of liability hereunder, Client-supplied Materials. If the cost of the Raw Material from any such Supplier is greater than Catalent’s costs for the same raw material of equal quality from other suppliers, Catalent shall add the difference between Catalent’s cost of the Raw Material and the Supplier’s cost of the Raw Material to the Unit Pricing. Client will be responsible for all costs associated with qualification of any such Supplier who has not been previously qualified by Catalent. In the case of Raw Materials in respect of which Client requires a specific Supplier to be used, Catalent shall not be liable for any delay in delivery of Product if Catalent is unable to obtain, in a timely manner, such particular Raw Material necessary to Manufacture or Package the Product, provided that Catalent placed orders for such Raw Materials promptly following receipt of Client’s Firm Commitment.