Performance and Consumption Measurements Sample Clauses

Performance and Consumption Measurements. The tests shall be set up to measure hourly average values of the parameters, listed below: • The hourly waste throughput in continuous operation. • The content of combustible material in bottom ash and fly ash. • The Total Organic Content (TOC) in the bottom ash. • The steam production, the steam pressure and the temperature. • The electricity production at the generator terminals and at the export meter. • The gaseous emission values (half hourly) and on request by the Department the emission values of the flue gas in the stack, including dioxin and relevant metals. • The consumption of: ; Electricity ; Steam ; Towns water ; Lime ; Activated carbon ; Ammonia ; Auxiliary fuel ; Other chemical reagents • The process related discharges: - Bottom ash - Boiler fly ash - Residue from flue gas cleaning • The noise measurements • Parameters, relevant to complete or verify the heat balance and consumption or useful for evaluation of the data, e.g.: ; Ambient temperature, hygrometry, atmospheric pressure ; Boiler exhaust flue gas temperature ; Boiler feedwater temperature ; HCl and SO2 content of the flue gas at the flue gas cleaning inlet ; Flue gas cleaning reactor exhaust temperature The heat balance in accordance with annex 1, Schedule 1 of the Project Agreement shall be used. It will determine the effective Net Calorific Value of the waste which, together with measured throughput, is required to compare the measured throughput value to the guaranteed performance on the Capacity Diagram. The measured nominal (maximum) throughput is to be compared with the largest nominal (maximum) throughput found on the line drawn for the measured Net Calorific Value in the Capacity Diagram. All measured consumption rates, except for the consumption of fuel oil, lime and ammonia and the quantity of the discharge residues will be corrected as follows, before comparison to the guaranteed consumption rates:- Corrected consumption = (measured consumption x(multiplied by) nominal waste heat input (within the capacity diagram))/calculated waste heat input. This calculation shall use the calculated waste heat input = measured waste throughput x (multiplied by) calculated Net Calorific Value The electricity consumption shall be determined by either direct measurement or by the deduction of the exported power from the produced power as measured at the terminals of the generator. In addition, the total measured electricity consumption shall be corrected for the power consumption that i...
Sample 1
AutoNDA by SimpleDocs

Related to Performance and Consumption Measurements

  • PERFORMANCE MEASUREMENTS Upon a particular Commission’s issuance of an Order pertaining to Performance Measurements in a proceeding expressly applicable to all CLECs generally, BellSouth shall implement in that state such Performance Measurements as of the date specified by the Commission. Performance Measurements that have been Ordered in a particular state can currently be accessed via the internet at xxxx://xxxx.xxxxxxxxx.xxx. The following Service Quality Measurements (SQM) plan as it presently exists and as it may be modified in the future, is being included as the performance measurements currently in place for the state of Tennessee. At such time that the TRA issues a subsequent Order pertaining to Performance Measurements, such Performance Measurements shall supersede the SQM contained in the Agreement. BellSouth Service Quality Measurement Plan‌ (SQM) Tennessee Performance Metrics Measurement Descriptions Version 2.00 Issue Date: July 1, 2003 Introduction

  • Performance Measures and Metrics This section outlines the performance measures and metrics upon which service under this SLA will be assessed. Shared Service Centers and Customers will negotiate the performance metric, frequency, customer and provider service responsibilities associated with each performance measure. Measurements of the Port of Seattle activities are critical to improving services and are the basis for cost recovery for services provided. The Port of Seattle and The Northwest Seaport Alliance have identified activities critical to meeting The NWSA’s business requirements and have agreed upon how these activities will be assessed.

  • Performance Measurement Satisfactory performance of this Contract will be measured by:

  • Performance Measures The System Agency will monitor the Grantee’s performance of the requirements in Attachment A and compliance with the Contract’s terms and conditions.

  • Metrics The DISTRICT and PARTNER will partake in monthly coordination meetings at mutually agreed upon times and dates to discuss the progress of the program Scope of Work. DISTRICT and PARTNER will also mutually establish criteria and process for ongoing program assessment/evaluation such as, but not limited to the DISTRICT’s assessment metrics and other state metrics [(Measures of Academic Progress – English, SBAC – 11th grade, Redesignation Rates, mutually developed rubric score/s, student attendance, and Social Emotional Learning (SEL) data)]. The DISTRICT and PARTNER will also engage in annual review of program content to ensure standards alignment that comply with DISTRICT approved coursework. The PARTNER will provide their impact data based upon these metrics.

  • Performance Indicators The HSP’s delivery of the Services will be measured by the following Indicators, Targets and where applicable Performance Standards. In the following table: n/a meanç ‘not-appIicabIe’, that there iç no defined Performance Standard for the indicator for the applicable year. tbd means a Target, and a Performance Standard, if applicable, will be determined during the applicable year. INDICATOR CATEGORY INDICATOR P = Performance Indicator E = Explanatory Indicator M = Monitoring Indicator 2019/20 PERFORMANCE TARGET STANDARD Organizational Health and Financial Indicators Debt Service Coverage Ratio (P) 1 c1 Total Margin (P) 0 cO Coordination and Access Indicators Percent Resident Days – Long Stay (E) n/a n/a Wait Time from LHIN Determination of Eligibility to LTC Home Response (M) n/a n/a Long-Term Care Home Refusal Rate (E) n/a n/a SCHEDULE D — PERFORMANCE 2/3 INDICATOR CATEGORY Quality and Resident Safety Indicators INDICATOR P = Performance Indicator E = Explanatory Indicator M = Monitoring Indicator Percentage of Residents Who Fell in the Last 30 days (M) 2019/20 PERFORMANCE TARGET STANDARD n/a n/a Percentage of Residents Whose Pressure Ulcer Worsened (M) n/a n/a Percentage of Residents on Antipsychotics Without a Diagnosis of Psychosis (M) n/a n/a Percentage of Residents in Daily Physical Restraints (M) n/a n/a SCHEDULE D — PERFORMANCE 2.0 LHIN-Specific Performance Obligations 3/3

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Benchmarks for Measuring Accessibility For the purposes of this Agreement, the accessibility of online content and functionality will be measured according to the W3C’s Web Content Accessibility Guidelines (WCAG) 2.0 Level AA and the Web Accessibility Initiative Accessible Rich Internet Applications Suite (WAI-ARIA) 1.0 for web content, which are incorporated by reference. Adherence to these accessible technology standards is one way to ensure compliance with the College’s underlying legal obligations to ensure that people with disabilities are able to acquire the same information, engage in the same interactions, and enjoy the same benefits and services within the same timeframe as their nondisabled peers, with substantially equivalent ease of use; that they are not excluded from participation in, denied the benefits of, or otherwise subjected to discrimination in any College programs, services, and activities delivered online, as required by Section 504 and the ADA and their implementing regulations; and that they receive effective communication of the College’s programs, services, and activities delivered online.

  • Ongoing Performance Measures The Department intends to use performance-reporting tools in order to measure the performance of Contractor(s). These tools will include the Contractor Performance Survey (Exhibit H), to be completed by Customers on a quarterly basis. Such measures will allow the Department to better track Vendor performance through the term of the Contract(s) and ensure that Contractor(s) consistently provide quality services to the State and its Customers. The Department reserves the right to modify the Contractor Performance Survey document and introduce additional performance-reporting tools as they are developed, including online tools (e.g. tools within MFMP or on the Department's website).

  • Performance Metrics In the event Grantee fails to timely achieve the following performance metrics (the “Performance Metrics”), then in accordance with Section 8.4 below Grantee shall upon written demand by Triumph repay to Triumph all portions of Grant theretofore funded to and received by Grantee:

Time is Money Join Law Insider Premium to draft better contracts faster.