Questions of WP7 Sample Clauses

Questions of WP7. Results What control is most needed on production to ensure that manufactured cylinders will behave as observed under type approval? The process of manufacturing composite cylinder can be considered a “special process”. Special processes are so called when the resulting output cannot be completely verified by subsequent monitoring or measurement of the product and, as a consequence, deficiencies become apparent only after the product is in use. For such processes, it is not possible to verify the characteristics of the product during pro- cessing without destroying the product as part of the evaluation. For these processes, the only alternative to destroying useable product is to ensure that the process is controlled to the degree that it is capable of producing only conforming product that behave as the validated one. To achieve this outcome, the control of these processes should establish arrangements which may include defined criteria for review and approval of the processes, approval of equipment and qualification of personnel, use of specific methods and procedures, requirements for records and revalidation. This involves defining which essential material and manufacturing parameters should be sub- ject to a quality assurance plan because they determine strength and resistance to degrada- tion. In addition to the control of the process, the adoption of subsequent inspections and meas- urements of the product, can bring to the detection of some characteristics, thus allowing the definition of acceptance criteria for the cylinders. Present standards generally address the production parameters identified in this study as influencing the performances of the cylinders and also prescribe a set of tests for the ac- ceptance of each production batch. In this study the manufacturing variation that has shown the bigger effect on the final perfor- xxxxx of the cylinder is MF4 (different fibre). The MF3 (Improper curing) caused also an im- portant effect on cyclic performance on Type 3 cylinder and on burst test scattering on Type 4 cylinder. The other manufacturing variations have shown a limited consequence on the cyl- xxxxx performance. The burst test prescribed by present regulations, norms and standards would detect the use of a different fibre, being the resistance of the cylinder proportional to the mechanical characteristics of the fibres. Improper curing has shown important effect on cyclic test performance of Type 3 cylinders and on the test results sca...
Sample 1
AutoNDA by SimpleDocs

Related to Questions of WP7

  • Conditions of Agreement This is a tentative Agreement and shall be of no force and effect unless and until all of the following occur:

  • Limitations of Services When using the Services, you may incur technical or other difficulties. We nor our service providers are responsible for any technical or other difficulties or any resulting damages that you may incur. Any information displayed or provided as part of the Services is for informational purposes only, may not reflect your most recent transactions, and should not be relied on for transactional purposes. We and our service providers reserve the right to change, suspend or discontinue any or all of the Services at any time without prior notice.

  • Conditions of Eft Services (a.) Ownership of Card(s). Any Card we supply to you is our property and must be returned to us, or to any person whom we authorize to act as our agent, or to any person who is authorized to honor the Card, immediately according to instructions. The Card may be reclaimed at any time at our sole discretion without demand or notice. You cannot transfer your Card to another person.

  • CONDITIONS OF WORK 4.1 The Contractor shall carefully examine and study the conditions under which the Work is to be performed and the site of the Work, and compare the Contract Documents with each other and to information furnished by the University including but not limited to the plans and specifications, the form of the Contract, General Conditions, Supplementary Conditions, General Requirements, Bonds and all other Contract Documents associated with the Work.

  • Conditions of Service (1). The Dallas County Community College District Dual Credit program falls under Texas Higher Education Coordinating Board Rule 19 TAC §§ 4.81-4.85, “Dual Credit Partnerships Between Secondary Schools and Texas Public Institutions of Higher Education.” Services under this Agreement are limited exclusively to Dual Credit for a tuition scholarship for approved Dual Credit courses (Attachment B). For Dual Credit scholarship see 4.K.1 of this Agreement.

  • GENERAL CONDITIONS OF CONTRACT 1. Definitions 1.1 In this Contract, the following terms shall be interpreted as indicated:

  • Conditions of Leave The Town Board will specify the duration of an unpaid leave of absence and to impose such other terms, conditions and restrictions on the employee as the Town Board, in its discretion, deems appropriate.

  • TERMS AND CONDITIONS OF AGREEMENT Except as specifically amended by this Amendment, all terms and conditions of the Agreement shall remain in full force and effect.

  • CONDITIONS OF CONTRACT The contractor shall at all times observe and comply with federal and State laws, local laws, ordinances, orders, and regulations existing at the time of or enacted subsequent to the execution of this contract which in any manner affect the completion of the work. The contractor shall indemnify and save harmless the agency and all its officers, representatives, agents, and employees against any claim or liability arising from or based upon the violation of any such law, ordinance, regulation, order or decree by an employee, representative, or subcontractor of the contractor.

  • Determinations of Director Pursuant to the Act and Section II of the Agreement and subject to the remaining terms and provisions of the Agreement and all Appendices thereto, the Director hereby determines that the financial assistance to be provided by the OPWC to the Recipient is in compliance with the Act and is provided to the Recipient for the sole and express purpose of financing the Eligible Project Cost and/or reimbursing the Recipient for such Eligible Project Cost.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!