Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Purchaser may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in A2. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
METERING AND BILLING Metering requirements and billing procedures shall be set forth in the AEC rate schedule(s) applicable to the electric service account assigned to the location where the Generating Facility is connected.
Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.
Archiving and Reuse Self-Archiving: The Publisher permits the Rights Holder to archive the Contribution in accordance with the Publisher's guidelines, the current version of which is set out in the Appendix "Author's Self-Archiving Guidelines".
Marketing and Outreach CONTRACTOR shall identify culturally and linguistically appropriate measures for reaching older adults in need of transportation and determine procedures for implementation of outreach, which may include, but is not limited to, brochures, flyers, and public presentations. In order to ensure effective collaboration and coordination of services, a CONTRACTOR shall be required to submit drafts of all printed materials related to outreach and marketing of OoA Senior Non-Emergency Medical Transportation Fixed-Price Per Mile Program services to OoA for approval before publication and dissemination.
Monitoring and Review 5.1 The Council and the BID Company shall set up the Standard Services Review Panel within 28 days from the date of this Agreement the purpose of which shall be to:
Monitoring and Recording COMMUNICATIONS - We may monitor and record communications between you and us, including telephone conversations, electronic messages, electronic records, or other data transmissions that affect your accounts or other products and services. Except as otherwise prohibited by applicable law, you agree we may monitor and record such communications without your approval or further notice to you.
Cutting and Patching The Contractor shall be responsible for cutting, fitting or patching required to complete the Work or to make its parts fit together properly.
Local Control Center, Metering and Telemetry The NTO shall operate, pursuant to ISO Tariffs, ISO Procedures, Reliability Rules and all other applicable reliability rules, standards and criteria on a twenty-four (24) hour basis, a suitable local control center(s) with all equipment and facilities reasonably required for the ISO to exercise ISO Operational Control over NTO Transmission Facilities Under ISO Operational Control, and for the NTO to fulfill its responsibilities under this Agreement. Operation of the NYS Power System is a cooperative effort coordinated by the ISO control center in conjunction with local control centers and will require the exchange of all reasonably necessary information. The NTO shall provide the ISO with Supervisory Control and Data Acquisition (“SCADA”) information on facilities listed in Appendices A-1 and A-2 herein as well as on generation and merchant transmission resources interconnected to the NTO’s transmission facilities pursuant to the ISO OATT. The NTO shall provide metering data for its transmission facilities to the ISO, unless other parties are authorized by the appropriate regulatory authority to provide metering data. The NTO shall collect and submit to the ISO billing quality metering data and any other information for its transmission facilities required by the ISO for billing purposes. The NTO shall provide to the ISO the telemetry and other operating data from generation and merchant transmission resources interconnected to its transmission facilities that the ISO requires for the operation of the NYS Power System. The NTO will establish and maintain a strict code of conduct to prevent such information from reaching any unauthorized person or entity.
PACKING AND MARKING Seller shall package all Goods shipped under this Order in accordance with the requirements in this Order, or, if requirements are not specified, in accordance with standard commercial practices customary for similar shipments. When shipping any Goods that are food or food packaging, Seller will ship the Goods under sanitary conditions using carriers suitable for the transport of such Goods that will not render the Goods contaminated with filth, injurious to health, or otherwise adulterated (e.g., carriers that have not been used to transport garbage, waste or other refuse). In each master carton or container in which Goods are shipped, Seller shall include a certificate of analysis, bill of lading, and packing list indicating this Order number, description, quantity, HSY item numbers, and other identifying information corresponding to the information in this Order. Seller shall clearly mark all packages in accordance with all applicable laws and shall label each unit of the Goods with the country of origin, weight, and name of manufacturer. Seller shall ensure that a receiving document/proof-of-delivery is issued to HSY for any shipment made to a third party location. All costs, fines or penalties incurred or assessed due to improper packing or marking will be Seller’s responsibility, and if paid by HSY, will be deducted from amounts owed to Seller. Seller will notify HSY of the number of packages, size, weight, method of protection during shipment and method of storage and protection upon arrival at destination.
