Class B devices Sample Clauses

Class B devices. The child restraint shall be firmly secured, and the webbing as specified in Annex 23 to this Regulation, shall pass through the lock-off and frame following the routing described in the manufacturer's instructions. The belt shall pass through the testing equipment as described in Figure 5 below and be attached to a mass of 5.25 ± 0.05 kg. There shall be 650 ± 40 mm of free webbing between the mass and the point where the webbing leaves the frame. The lock-off shall be fully applied and a xxxx made on the belt where it enters the lock-off. The mass shall be raised and released so that it falls freely over a distance of 25 ± 1 mm. This shall be repeated 100 times ±2 at a frequency of 60 ± 2 cycles per minute, to simulate the jerking action of a child restraint in a vehicle. A further xxxx shall be made on the belt where it enters the lock-off and the distance between the two marks shall be measured. The lock-off device shall cover the full width of the webbing in the installed condition with Q3 dummy installed. This test is to be conducted using the same webbing angles as those formed in normal use. The free end of the lap belt portion shall be fixed. The test shall be conducted with the child restraint system firmly attached to the test bench used in the overturning or dynamic test. The loading strap can be attached to the simulated buckle.
Sample 1Sample 2Sample 3See All (11)
AutoNDA by SimpleDocs
Class B devices. The child restraint shall be firmly secured and webbing, as specified in Annex 13 to this Regulation, shall be passed through the lock-off and frame following the routing described in the manufacturer's instructions. The belt shall pass through the testing equipment as described in Figure 6 below and be attached to a mass of 5.25 ± 0.05 kg. There shall be 650 ± 40 mm of free webbing between the mass and the point where the webbing leaves the frame. The lock-off shall be fully applied and a xxxx made on the belt where it enters the lock-off. The mass shall be raised and released so that it falls freely over a distance of 25 ± 1 mm. This shall be repeated 100 times ± 2 at a frequency of 60 ± 2 cycles per minute, to simulate the jerking action of a child restraint in a car. A further xxxx shall be made on the belt where it enters the lock-off and the distance between the two marks shall be measured. The lock-off device must cover the full width of the webbing in the installed condition with 15 kg dummy installed. This test is to be conducted using the same webbing angles as those formed in normal use. The free end of the lap belt portion shall be fixed. The test shall be conducted with the child restraint system firmly attached to the test bench used in the overturning or dynamic test. The loading strap can be attached to the simulated buckle. roller guide roller bar mass 25 mm to child restraint frame and lock-off Drop height of mass = 25 mm Distance from roller bar to roller guide = 300 mm Using strap of the webbing specified for the standard seat belt as defined in Annex 13. Figure 6: Schematic layout of Class B Lock-off test.
Sample 1See All (4)

Related to Class B devices

  • Class Size The School shall be in compliance with Florida Constitutional Class Size Requirements, as applicable to charter schools.

  • Class Sizes In the annual assignment of duties, the designated supervisor shall consult with the department in determining appropriate class sizes for individual courses. In making such a determination, the designated supervisor shall consider operational requirements, sound pedagogical principles, and the workload implication of teaching such courses (also see Letter of Understanding #3).

  • SPECIALIZED JOB CLASSES Where there is a particular specialized job class in which the pay rate is below the local market value assessment of that job class, the parties may use existing means under the collective agreement to adjust compensation for that job class.

  • Components Patheon will purchase and test all Components (with the exception of Client-Supplied Components) at Patheon’s expense and as required by the Specifications.

  • Schematic Design Phase Services § 3.2.1 The Architect shall review the program and other information furnished by the Owner, and shall review laws, codes, and regulations applicable to the Architect’s services.

  • Schematic Design Phase INDICATE IN STATEMENT OF WORK “NOT APPLICABLE” IF SECTION IS NOT APPLICABLE

  • Class All REMIC I Regular Interests or the Class R-1 Residual Interest having the same priority and rights to payments on the Mortgage Loans from the REMIC I Available Distribution Amount, all REMIC II Regular Interests or the Class R-2 Residual Interest having the same priority and rights to payments on the REMIC I Regular Interests from the REMIC II Available Distribution Amount, and all REMIC III Regular Interests or the Class R-3 Residual Interest having the same priority and rights to payments on the REMIC II Regular Interests from the REMIC III Available Distribution Amount, as applicable, which REMIC I Regular Interests, REMIC II Regular Interests, REMIC III Regular Interests and Class R Residual Interests, as applicable, shall be designated as a separate Class, and which, in the case of the Certificates (including the Class R Certificates representing ownership of the Class R Residual Interests), shall be set forth in the applicable forms of Certificates attached hereto as Exhibits A and B. Each Class of REMIC I Regular Interests and the Class R-1 Residual Interest shall be entitled to receive the amounts allocated to such Class pursuant to the definition of "REMIC I Distribution Amount" only to the extent of the REMIC I Available Distribution Amount for such Distribution Date remaining after distributions in accordance with prior clauses of the definition of "REMIC I Distribution Amount," each Class of REMIC II Regular Interests and the Class R-2 Residual Interest shall be entitled to receive the amounts allocated to such Class pursuant to the definition of "REMIC II Distribution Amount" only to the extent of the REMIC II Available Distribution Amount for such Distribution Date remaining after distributions in accordance with prior clauses of the definition of "REMIC II Distribution Amount" and each Class of REMIC III Regular Interests and the Class R-3 Residual Interest shall be entitled to receive the amounts allocated to such Class pursuant to the definition of "REMIC III Distribution Amount" only to the extent of the REMIC III Available Distribution Amount for such Distribution Date remaining after distributions in accordance with prior clauses of the definition of "REMIC III Distribution Amount."

  • Class Load 1. The teaching load of a teacher of the secondary school (six through twelve) will be limited to not more than five (5) preparations of different subject areas and/or levels. R: 03

  • CLASS SIZE/STAFFING LEVELS The board will make every effort to limit FDK/Grade 1 split grades where feasible. APPENDIX A – RETIREMENT GRATUITIES

  • Program Components Activities and services delivered under this Program Element align with Foundational Programs and Foundational Capabilities, as defined in Oregon’s Public Health Modernization Manual, (xxxx://xxx.xxxxxx.xxx/oha/PH/ABOUT/TASKFORCE/Documents/public_health_modernization_man ual.pdf) as well as with public health accountability outcome and process metrics (if applicable) as follows:

Time is Money Join Law Insider Premium to draft better contracts faster.