Fittings and Specials Sample Clauses

Fittings and Specials. Add the following: "All bends, fittings and specials shall be manufactured from straight pipe specified elsewhere unless otherwise stated in the Bills of Quantities The lengths of the pipes shall be as dimensioned on the drawings but shall be verified on site prior to fabrication. All steel pipes & fittings larger than DN 150 to be FBE or solvent free epoxy coated and lined to minimum thickness of 400 micron unless otherwise specified. All steel bends, fittings and specials shall be fabricated to the dimensions and details shown on the drawings and/or described in the Bills of Quantities. Where drawings containing pipework and fittings do not have dimensions and have not been individually itemized on the drawings or bill of quantities, the pipework design, supply, delivery, handle install, test and commission is the Contractors responsibility. This shall be scheduled in the bill of quantities, as well as described in the Project Specifications and/ or indicated indicatively in the drawings. The sides of taper pieces shall diverge at an angle of not more than 11° to each other. All steel pipes & fittings larger than DN150 to have either a minimum 4.0mm wall thickness to SABS 719 Grade B or to have a diameter to thickness ratio of 125, whichever is greater. Individual bends, fittings and specials DN150 and smaller shall be hot-dip galvanised to heavy duty grade in accordance with SANS 121 after fabrication. Where a hot dipped galvanised fitting is to be welded to a coated and lined pipe, the galvanising is to be abraded off prior to welding. The external coating at the welded joint is to be primed and coated with an approved anti corrosion system as specified elsewhere. Bends, fittings, and specials Larger than DN150 shall have the internal lining and external coating made continuous (“made good”) as specified elsewhere for welded joints on coated and lined pipes. Bends, fittings and specials shall be manufactured and tested in accordance with the specification for straight pipe and additionally with Section 8 of BS EN 10311: 2005 and BS 10224: 2002. The nominal dimensions of each bend, fitting and special required are itemised in the Bills of Quantities and/or on the drawings and ‘exact length’ tolerances shall be adhered to – subject to verification on site prior to fabrication. All plain ends on bends, fittings and specials shall have the plain ends prepared for butt welding except those plain ends that are to be jointed with adaptor joints or bell ends. ...
AutoNDA by SimpleDocs

Related to Fittings and Specials

  • Training a. The employer, in consultation with the local, shall be responsible for developing and implementing an ongoing harassment and sexual harassment awareness program for all employees. Where a program currently exists and meets the criteria listed in this agreement, such a program shall be deemed to satisfy the provisions of this article. This awareness program shall initially be for all employees and shall be scheduled at least once annually for all new employees to attend.

  • Construction The parties agree that each of them and/or their respective counsel have reviewed and had an opportunity to revise the Transaction Documents and, therefore, the normal rule of construction to the effect that any ambiguities are to be resolved against the drafting party shall not be employed in the interpretation of the Transaction Documents or any amendments thereto. In addition, each and every reference to share prices and shares of Common Stock in any Transaction Document shall be subject to adjustment for reverse and forward stock splits, stock dividends, stock combinations and other similar transactions of the Common Stock that occur after the date of this Agreement.

  • Scope of Work For the 2022/2023 Grant Period, the Provider will maintain a victim services program that will be available to provide direct services to victims of crime who are identified by the Provider or are presented to the Provider, as specified in the Provider’s 2022/2023 Grant Application as approved by the OAG and incorporated herein by reference.

  • Safety Where an employee is prevented from working at the employee’s particular function as a result of unsafe conditions caused by the inclement weather, the employee may be transferred to other work in the employee’s classification on site, until the unsafe conditions are rectified. Where such alternative is not available and until the unsafe conditions are rectified, the employee shall remain on site. The employee shall be paid for such time without reduction of the employees’ inclement weather entitlement.

  • Scope of Services The specific scope of work for each job shall be determined in advance and in writing between TIPS Member, Member’s design professionals and Vendor. It is permitted for the TIPS Member to provide a general scope description, but the awarded vendor should provide a written scope of work, and if applicable, according to the TIPS Member’s design Professional as part of the proposal. Once the scope of the job is agreed to, the TIPS Member will issue a PO and/or an Agreement or Contract with the Job Order Contract Proposal referenced or as an attachment along with bond and any other special provisions agreed by the TIPS Member. If special terms and conditions other than those covered within this solicitation and awarded Agreements are required, they will be attached to the PO and/or an Agreement or Contract and shall take precedence over those in this base TIPS Vendor Agreement.

  • Maintenance All costs for maintaining, operating, replacing, repairing, white-washing, painting, decorating, re-decorating, re-building, re-constructing, lighting and renovating the Common Areas [including the exterior or interior (but not inside any apartment) walls of the Said Block/Building] and the road network, STP etc.

  • Scope Notwithstanding any other provision of this Agreement, the Company hereby agrees to indemnify the Indemnitee to the fullest extent permitted by law, notwithstanding that such indemnification is not specifically authorized by the other provisions of this Agreement, the Company’s Certificate of Incorporation, the Company’s Bylaws or by statute. In the event of any change, after the date of this Agreement, in any applicable law, statute, or rule which expands the right of a Delaware corporation to indemnify a member of its board of directors or an officer, such changes shall be deemed to be within the purview of Indemnitee’s rights and the Company’s obligations under this Agreement. In the event of any change in any applicable law, statute or rule which narrows the right of a Delaware corporation to indemnify a member of its board of directors or an officer, such changes, to the extent not otherwise required by such law, statute or rule to be applied to this Agreement shall have no effect on this Agreement or the parties’ rights and obligations hereunder.

  • HOURS OF WORK i) Where employees are now working a longer daily tour, the provisions set out in this Article governing the regular hours of work on a daily tour shall be adjusted accordingly.

  • Force Majeure If by reason of Force Majeure, either party hereto shall be rendered unable wholly or in part to carry out its obligations under this Agreement then such party shall give notice and full particulars of Force Majeure in writing to the other party within a reasonable time after occurrence of the event or cause relied upon, and the obligation of the party giving such notice, so far as it is affected by such Force Majeure, shall be suspended during the continuance of the inability then claimed, except as hereinafter provided, but for no longer period, and such party shall endeavor to remove or overcome such inability with all reasonable dispatch. Choice of Law The Agreement between the Vendor and TIPS/ESC Region 8 and any addenda or other additions resulting from this procurement process, however described, shall be governed by, construed and enforced in accordance with the laws of the State of Texas, regardless of any conflict of laws principles. Venue, Jurisdiction and Service of Process Any Proceeding arising out of or relating to this procurement process or any contract issued by TIPS resulting from or any contemplated transaction shall be brought in a court of competent jurisdiction in Camp County, Texas and each of the parties irrevocably submits to the exclusive jurisdiction of said court in any such proceeding, waives any objection it may now or hereafter have to venue or to convenience of forum, agrees that all claims in respect of the Proceeding shall be heard and determined only in any such court, and agrees not to bring any proceeding arising out of or relating to this procurement process or any contract resulting from or any contemplated transaction in any other court. The parties agree that either or both of them may file a copy of this paragraph with any court as written evidence of the knowing, voluntary and freely bargained for agreement between the parties irrevocably to waive any objections to venue or to convenience of forum. Process in any Proceeding referred to in the first sentence of this Section may be served on any party anywhere in the world. Venue for any dispute resolution process, other than litigation, between TIPS and the Vendor shall be located in Camp or Xxxxx County, Texas.

  • Audits No more than once a year, or following unauthorized access, upon receipt of a written request from the LEA with at least ten (10) business days’ notice and upon the execution of an appropriate confidentiality agreement, the Provider will allow the LEA to audit the security and privacy measures that are in place to ensure protection of Student Data or any portion thereof as it pertains to the delivery of services to the LEA . The Provider will cooperate reasonably with the LEA and any local, state, or federal agency with oversight authority or jurisdiction in connection with any audit or investigation of the Provider and/or delivery of Services to students and/or LEA, and shall provide reasonable access to the Provider’s facilities, staff, agents and XXX’s Student Data and all records pertaining to the Provider, LEA and delivery of Services to the LEA. Failure to reasonably cooperate shall be deemed a material breach of the DPA.

Time is Money Join Law Insider Premium to draft better contracts faster.