Setting Out of Work Sample Clauses

Setting Out of Work. Reference and level beacons will be shown to the Contractor by the Municipality at the commencement of the Contract and the Contractor will be responsible for transferring the datum to the Site of Works. The Contractor shall check the condition and accuracy of all reference and level beacons and satisfy himself that they have not been disturbed and are true with regard to position and level. A beacon that has been disturbed shall not be used until its true position and level have been re-established and the new values have been certified by the Municipality. The Contractor shall thereafter be held entirely responsible for the protection of all reference and level beacons.
Sample 1Sample 2
AutoNDA by SimpleDocs
Setting Out of Work. 11.2 Setting out of Work is sole responsibility of the Contractor.
Sample 1
Setting Out of Work. .1 Assume full responsibility for and execute complete layout of work to locations indicated.
Sample 1

Related to Setting Out of Work

  • Cost of Work The Cost of Work will be adjusted and finalized as part of the Contract Sum in the GMP. The budget for the Cost of Work shall not exceed Five Million Three Hundred Six Thousand Eight Hundred Five and No/100 Dollars ($5,306,805.00).

  • LAYOUT OF WORK The Contractor shall lay out its Work from base lines and benchmarks indicated on the Drawings, and shall be responsible for verification of all measurements in connection with the layout. The Contractor shall furnish all stakes, templates, platforms, equipment, tools, materials, and labor required to lay out any part of the Work. The Contractor shall also be responsible for maintaining and preserving all stakes and other marks established by Princeton University until authorized to remove them. If such marks are destroyed by the Contractor or through its negligence before their removal is authorized, Princeton University may replace them and deduct the expense of the replacement from any amounts due or to become due to the Contractor. CLAUSE C15 NOISE

  • Xxxxx of Work The Contractor shall provide information technology (IT) independent verification and validation (IV&V) services to Customers in accordance with this Statement of Work (SOW). The Contractor shall provide the professional and technical staff necessary to perform the ((IT) IV&V services required by this Contract, and the staff shall have sufficient skill and experience to perform the services assigned to them. All of the (IT) IV&V services to be furnished by the Contractor under the Contract shall meet the professional standard and quality that prevail among IT professionals in the same discipline and of similar knowledge and skill engaged in related work under the same or similar circumstances. The Contractor shall maintain during the term of the Contract all licenses, permits, qualifications, insurance, and approvals of whatever nature that are legally required to perform the (IT) IV&V services.

  • UNCOVERING OF WORK 13.1.1 If any portion of the Work should be covered contrary to the request of the Architect or to requirements specifically expressed in the Contract Documents, it must, if required in writing by the Architect, be uncovered for his or her observation and shall be replaced at the Contractor's expense.

  • Statement of Work The Contractor shall provide the services and staff, and otherwise do all things necessary for or incidental to the performance of work, as set forth below:

  • CORRECTION OF WORK 13.2.1 The Contractor shall be responsible for correcting all Work which the Architect has found to be defective or which fails to conform to the Contract Documents whether observed be- fore or after Substantial Completion and whether or not fabricated, installed or completed. The Contractor shall bear all costs of correcting such rejected Work, including compensation for the Architect's and the State’s additional services made necessary thereby. The Architect, upon a finding of defect or failure to conform, shall immediately notify the State and Contractor, in writing, of the defect. The Contractor shall begin correcting the defective or non-conforming Work within ten (10) days unless the State agrees to a Change Order which reflects the reduction in Contract Sum due to the value of diminishment of the defective or nonconforming Work.

  • Rejection of Work Using the Notice of Non-Conforming Work procedures outlined in the General Conditions, the Design Professional shall reject work that does not comply with the requirements of the Contract Documents or that does not comply with the applicable laws and codes. The Design Professional shall have authority to order testing of the Work, as is provided in the Contract Documents or as otherwise required in its judgment, whether such work is fabricated, installed, or completed.

  • Scope of Work The Contractor has overall responsibility for and shall provide and furnish all materials, equipment, tools and labor as necessary or reasonably inferable to complete the Work, or any phase of the Work, in accordance with the Owner’s requirements and the terms of the Contract Documents.

  • Location of Work The Executive shall be based in the United States in West Orange, New Jersey. However, the Executive agrees to undertake whatever domestic and worldwide travel is required by the Company. The Executive shall not be required or permitted to relocate without the mutual, written consent of the Executive and the Company.

  • Work Order (s) means a detailed scope of work for a Service required by Transnet, including timeframes, Deliverable, Fees and costs for the supply of the Service to Transnet, which may be appended to this Agreement from time to time.

Time is Money Join Law Insider Premium to draft better contracts faster.