Minimum Qualifications If applicable pursuant to Article 3, I acknowledge that the Bidder meets the minimum qualification requirements established for this solicitation.
Professional Qualifications It shall be a condition of continued professional employment that employees must apply for enrolment in their appropriate professional licensing body by the thirtieth day of continuous service.
Required Qualifications At all times during the term of the Contract, Vendor shall have available, under direct employment and supervision and/or subcontract agreement fully incorporating the terms and conditions of the Contract Documents, the required qualified and properly licensed (as applicable) personnel to properly fulfill all the terms and conditions of the Contract.
File Naming Conventions Files will be named according to the following convention: {gTLD}_{YYYY-MM-DD}_{type}_S{#}_R{rev}.{ext} where: {gTLD} is replaced with the gTLD name; in case of an IDN-TLD, the ASCII-compatible form (A-Label) must be used; {YYYY-MM-DD} is replaced by the date corresponding to the time used as a timeline watermark for the transactions; i.e. for the Full Deposit corresponding to 2009-08-02T00:00Z, the string to be used would be “2009-08-02”; {type} is replaced by: “full”, if the data represents a Full Deposit; “diff”, if the data represents a Differential Deposit; “thin”, if the data represents a Bulk Registration Data Access file, as specified in Section 3 of Specification 4; {#} is replaced by the position of the file in a series of files, beginning with “1”; in case of a lone file, this must be replaced by “1”. {rev} is replaced by the number of revision (or resend) of the file beginning with “0”: {ext} is replaced by “sig” if it is a digital signature file of the quasi-homonymous file. Otherwise it is replaced by “ryde”.
STAFF QUALIFICATIONS CONTRACTOR shall ensure that all individuals employed, contracted, and/or otherwise hired by CONTRACTOR to provide classroom and/or individualized instruction or related services hold a license, certificate, permit, or other document equivalent to that which staff in a public school are required to hold in the service rendered consistent with Education Code section 56366.1(n)(1) and are qualified pursuant to Title 34 of the Code of Federal Regulations sections 200.56 and 200.58, and Title 5 of the California Code of Regulations sections 3001(y), 3064 and 3065. Such qualified staff may only provide related services within the scope of their professional license, certification or credential and ethical standards set by each profession, and not assume responsibility or authority for another related services provider or special education teacher’s scope of practice. CONTRACTOR shall ensure that all staff are appropriately credentialed to provide instruction and services to students with the disabling conditions placed in their program/school through documentation provided to the CDE (5 CCR 3064 (a)).
LEAVE FOR REGULATORY BUSINESS AS PER THE TEACHERS’ ACT 1. Upon written request to the Superintendent or designate from the Ministry of Education, an employee who is appointed or elected to the BC Teachers’ Council or appointed to the Disciplinary or Professional Conduct Board shall be entitled to a leave of absence with pay and shall be deemed to be in the full employ of the board as defined in Article G.6.1.
2. Upon written request to the superintendent or designate from the Ministry of Education, a teacher teaching on call (TTOC) who is appointed or elected to the BC Teachers’ Council or appointed to the Disciplinary and Professional Conduct Board shall be considered on leave and shall be deemed to be in the full employ of the Board as defined in Article A.10.1 above. TTOCs shall be paid in accordance with the collective agreement.
3. Leave pursuant to Article A.10.1 and A.10.2 above shall not count toward any limits on the number of days and/or teachers on leave in the provisions in Article G.6.
Certification of Meeting or Exceeding Tobacco-Free Workplace Policy Minimum Standards A. Grantee certifies that it has adopted and enforces a Tobacco-Free Workplace Policy that meets or exceeds all of the following minimum standards of:
i. Prohibiting the use of all forms of tobacco products, including but not limited to cigarettes, cigars, pipes, water pipes (hookah), bidis, kreteks, electronic cigarettes, smokeless tobacco, snuff and chewing tobacco;
ii. Designating the property to which this Policy applies as a "designated area,” which must at least comprise all buildings and structures where activities funded under this Grant Agreement are taking place, as well as Grantee owned, leased, or controlled sidewalks, parking lots, walkways, and attached parking structures immediately adjacent to this designated area;
iii. Applying to all employees and visitors in this designated area; and
iv. Providing for or referring its employees to tobacco use cessation services.
B. If Grantee cannot meet these minimum standards, it must obtain a waiver from the System Agency.
Please see the current Washtenaw Community College catalog for up-to-date program requirements Conditions & Requirements
Contractor Qualifications Contractor warrants that Contractor has the necessary licenses, experience and technical skills to provide services under this Contract.
CFR PART 200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, class, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
