Electrocution definition

Electrocution means death resulting from an electric shock.
Electrocution means an injury arising from exposure to electricity which results in death or is of sufficient severity to require admission to a health care facility.
Electrocution means death resulting from an electric shock. Electricity supply systems typically operate at 230 volts AC phase to earth and 400 volts AC phase to phase. A shock at these voltages can be fatal. Hence, it is essential that adequate precautions are taken to ensure no person comes into contact with any ‘live’ electrical equipment or conductors. A high voltage shock (of 1,000 volts or more) may inflict other forms of serious injury such as severe burns and organ failure. Under normal circumstances, voltages below 50 volts AC generally are not harmful to humans. However, they must still be treated with respect, especially in wet or polluted areas. Burns Electricity flashovers/arcs produce very high temperature gases, and can cause severe burns and permanent disfigurement. Inhalation can also inflict severe internal burns on the victim’s airways. The risk of injury from arcing or explosion is extreme when high fault currents are present. This typically applies to low voltage circuits close to transformers or switchboards, where electrical protection may only detect and interrupt an arcing fault slowly or not at all. High energy electrical arcs are often explosive and also cause injury through impact from flying debris. Falls Falls from ladders, scaffolds or other elevated work platforms can occur as a direct consequence of an electric shock or arc blast, resulting potentially in serious injury or death. Poisoning Burning and arcing associated with electrical equipment may release various harmful gases and contaminants. Inhalation of these dangerous products may cause short term or chronic illness or result in death from suffocation. Fire Workers using electricity may not be the only ones at risk. Faulty electrical equipment and poor electrical installations can lead to fires that may also cause injury or death to others and property loss.4 Safe working practicesBefore starting work• Plan and discuss the job. Include a risk assessment.• Think about what is to be done, including isolation requirements.• Ensure all workers have the appropriate PPE and its condition is satisfactory. PPE will provide only limited protection from electrical risks such as electric shock, arc flash and arc blast.• Check if the upstream electrical protection has a maintenance setting that enables an immediate circuit trip if any fault occurs.• Confirm permission to isolate (comply with any access or vicinity permit system applicable to the site).• Isolate the electrical equipment or cir...

Examples of Electrocution in a sentence

  • Electrocution can occur without direct contact.7. Do not operate machine when any guards are removed.8. Inspect welds and repair if needed.

  • Electrocution can occur without direct contact.3. Be familiar with machine hazard area.

  • Instruct all employees of the common deadly hazards and how to avoid them, such as Falls; Equipment Turnover; Electrocution; Struck by/Caught In; Trench Cave In; Heat Stress and Drowning.

  • Denno, When Legislatures Delegate Death: The Troubling Paradox Behind State Uses of Electrocution and Lethal Injection and What It Says About Us, 63 OHIO ST.

  • Electrocution refers to the scenario where a bird is perched or attempts to perch on the electrical structure and causes an electrical short circuit by physically bridging the air gap between live components and/or live and earthed components (van Rooyen 2004).

  • A motion was made by Commissioner Holmes, supported by Commissioner Bergdahl and carried unanimously to approve the May 6, 2009, minutes as presented.

  • Electrocution hazard." Label circuits in hidden locations but which may be affected by the work in a similar manner.

  • Electrocution during the testing and charging: It has also been reported [OSHA's Integrated Management Information System (IMIS) database] that there has been fatalities due to electrocution.

  • Electrocution occurs when birds with large wingspans come in contact with two conductors or a conductor and a grounding device.

  • If TMO approves the application, it will be moved to the next step and if it is rejected ticket will be closed with comments, and the intimation SMS would be generated for the requestor.5th Step After the approval of TMO, in this step store keeper will issue required equipments on same day.6th Step This step wraps up process flow of street lights through installation of required equipments by Electrocution.


More Definitions of Electrocution

Electrocution means death resulting from an electric shock. Electricity supply systems typically operate at 230 volts AC phase to earth and 400 volts AC phase to phase. A shock at these voltages can be fatal. Hence, it is essential that adequate precautions are taken to ensure no person comes into contact with any ‘live’ electrical equipment or conductors. A high voltage shock (of 1,000 volts or more) may inflict other forms of serious injury such as severe burns and organ failure. Under normal circumstances, voltages below 50 volts AC generally are not harmful to humans. However, they must still be treated with respect, especially in wet or polluted areas. Burns Electricity flashovers/arcs produce very high temperature gases, and can cause severe burns and permanent disfigurement. Inhalation can also inflict severe internal burns on the victim’s airways. The risk of injury from arcing or explosion is extreme when high fault currents are present. This typically applies to low voltage circuits close to transformers or switchboards, where electrical protection may only detect and interrupt an arcing fault slowly or not at all. High energy electrical arcs are often explosive and also cause injury through impact from flying debris. Falls Falls from ladders, scaffolds or other elevated work platforms can occur as a direct consequence of an electric shock or arc blast, potentially resulting in serious injury or death. Poisoning Burning and arcing associated with electrical equipment may release various harmful gases and contaminants. Inhalation of these dangerous products may cause short term or chronic illness or result in death from suffocation. Fire Workers using electricity may not be the only ones at risk. Faulty electrical equipment and poor electrical installations can lead to fires that may also cause injury or death to others and property loss.4 Safe working practicesRemember, if in doubt about your safety or the safety of others, ask your supervisor. Isolation and safe working procedures are an essential part of every electrician’s job and, if practiced correctly, can prevent injury or save a life. As an apprentice, your supervisor is required to explain the correct procedures to be followed and you need to clearly understand these before you start work. Good safe working practices include: Before starting work• Plan and discuss the job - assess any safety risks.• Identify the means of safe electrical isolation.• Ensure that you receive explicit instructions (writte...
Electrocution means death by electric shock but does not include death from lightning, and which attracts ICD code 994.8;

Related to Electrocution

  • Sensor means any measurement device that is not part of the vehicle itself but installed to determine parameters other than the concentration of gaseous and particle pollutants and the exhaust mass flow.

  • Exfiltration means any unauthorized release of data from within an information system. This includes copying the data through covert network channels or the copying of data to unauthorized media.

  • Fluoroscopic imaging assembly means a subsystem in which X-ray photons produce a visual image. It includes the image receptor(s) such as the image intensifier and spot-film device, electrical interlocks, if any, and structural material providing linkage between the image receptor and diagnostic source assembly.

  • Electrostatic application means the application to a substrate of charged atomized paint droplets that are deposited by electrostatic attraction.

  • Fluid means material or substance which flows or moves whether in a semisolid, liquid, sludge, gas, or any other form or state.

  • Electrostatic spray means a method of applying a spray coating in which opposite electric charges are applied to the substrate and the coating. The coating is attracted to the substrate by the electrostatic potential between them.

  • Membrane filtration means a pressure or vacuum driven separation process in which particulate matter larger than 1 micrometer is rejected by an engineered barrier, primarily through a size-exclusion mechanism, and which has a measurable removal efficiency of a target organism that can be verified through the application of a direct integrity test. This definition includes the common membrane technologies of microfiltration, ultrafiltration, nanofiltration, and reverse osmosis.

  • Infiltration means water other than wastewater that enters a sewer system (including sewer system and foundation drains) from the ground through such means as defective pipes, pipe joints, connections, or manholes. Infiltration does not include, and is distinguished from, inflow.

  • Filtration means a process for removing particulate matter from water by passage through porous media.

  • Hydraulic fracturing means the fracturing of underground rock formations, including shale and non-shale formations, by manmade fluid-driven techniques for the purpose of stimulating oil, natural gas, or other subsurface hydrocarbon production.

  • Propagation means the reproduction of Regulated Marijuana plants by seeds, cuttings, or grafting.

  • Vaping means using an activated electronic delivery device or heated tobacco product.

  • Fabrication means making up data or results and recording or reporting them.

  • Backpressure means a pressure (caused by a pump, elevated tank or piping, boiler, or other means) on the consumer's side of the service connection that is greater than the pressure provided by the public water system and which may cause backflow.

  • Isolation means a behavior management technique in which a student is placed alone in an enclosed space from which the student is not prevented from leaving.

  • Fluoroscopy means a technique for generating x-ray images and presenting them simultaneously and continuously as visible images. This term has the same meaning as the term "radioscopy" in the standards of the International Electrotechnical Commission.

  • Encapsulant means a substance that forms a barrier between lead-based paint and the environment using a liquid-applied coating (with or without reinforcement materials) or an adhesively bonded covering material.

  • Assembly means an item forming a portion of a system or subsystem that—

  • Encapsulation means the application of an encapsulant.

  • Blasting means changing the level or grade of land or rendering, tearing, demolishing, moving, or removing earth, rock, buildings, structures, or other masses or materials by seismic blasting or the detonation of dynamite or any other explosive agent.

  • Grinding means to reduce to powder or small fragments and includes mechanical chipping or drilling.

  • Sterilization means the procedure that kills all microorganisms, including their spores.

  • Tissue means a portion of the human body other than an organ or an eye. The term does not include blood unless the blood is donated for the purpose of research or education.

  • Substrate means the surface onto which a coating is applied or into which a coating is impregnated.

  • Optical means services related to the provision of glasses, contact lenses, tests and treatments carried out by a registered optometrist or ophthalmologist.

  • Cell means a single encased electrochemical unit containing one positive and one negative electrode which exhibits a voltage differential across its two terminals.