Design Builder's Representative. Design-Builder shall designate, by written notice to Owner on or before the Notice to Proceed, an individual (“Project Manager”) who shall be authorized to act on behalf of Design-Builder, with whom Owner may consult at all reasonable times, who shall have full supervision over the completion of the Work, who shall be designated to act as the primary point of contact with Owner regarding all matters relating to the Work, and who shall have full authority to bind Design-Builder except to the extent such authority is limited as described in such notice. If the Project Manager’s authority is limited, the notice will identify such persons within Design-Builder’s organization who do have full authority to bind Design- Builder for all purposes under the Contract Documents. Design-Builder may, at any time by written notice to Owner, change the persons, if any, previously identified as having authority beyond that of the Project Manager. Any changes in the Project Manager shall require Owner’s prior written approval.
Design Builder's Representative. Design Builderdesignates the individual listed below as its Design Builder's Representative to provide direct interface with Owner with respect to Design Builder's responsibilities:
Design Builder's Representative. 3.2.1 Design-Builder’s Representative shall be responsible for providing Design-Builder-supplied information and approvals in a timely manner to permit Design-Build Subcontractor to fulfill its obligations under the Contract Documents.
Design Builder's Representative. The Design-Builder shall designate a person who shall be the Design-Builder's authorized representative. The Design-Builder's Representative is: Xx. Xxxx Xxxxx.
Design Builder's Representative. Design Builderdesignates the individual listed below as its Design Builder's Representative to provide direct interface with Owner with respect to Design Builder's responsibilities: Xxxx Xxxxxxx, Design Builder's Project Manager. Exhibit C- Project Assignment Page 3 of 4 Exhibit C-1 – List of Contract Documents Page 1 of 1
1. GMP based on removing the existing walk-in cooler/freezer in the Culinary Lab and installing a prefabricated cooler and freezer from Polar King.
2. GMP based on installation taking place in summer 2019 while classroom and lab are unoccupied.
3. Preconstruction fees are not included in the GMP total. $145,159.81 (One Hundred Forty-Five Thousand One Hundred Fifty-Nine Dollars and Eighty-One Cents) A TOTAL ALL DIVISIONS 87,994.12 F TOTAL COST OF WORK 118,334.73 K TOTAL PROPOSED GMP (F+G+H+l+J) 145,159.81 MHS Culinary Renovation – Melbourne, FL GENERAL CLARIFICATIONS & QUALIFICATIONS GENERAL NOTES
1. The following items are included:
a. Project management and supervision
b. Jobsite safety equipment
c. Temporary sanitary facilities and clean-up
d. Hoisting
e. Temporary sidewalk staging
f. Blueprints, as-built drawings, close-out documents
g. Surveying, soil testing, concrete testing
h. Taxes
i. Design fees j. 12 month warranty starting from the date of substantial completion k. Payment and performance bonds l. Builder’s risk insurance
2. The following items are not included:
a. Boundary survey and benchmark
b. Field office/trailer
c. Impact fees or building permit fees
d. Utility service provider meter and connection fees
e. Threshold inspections
f. Third party testing and inspections including building envelope, roofing/flashing, and mold/mildew inspections
g. Radon mitigation systems
h. Fixtures, furnishings, and equipment unless otherwise noted in this document i. Work resulting from code interpretations by the Authorities Having Jurisdiction (AHJ’s) which were not contemplated in this contract
3. Contractor assumes the existing kitchen will not be used at any point in the Summer of 2019.
4. All allowance numbers are inclusive of all material, sales tax, delivery, stocking, labor and equipment for
1. The following items are included:
a. Remove existing walk-in cooler/freezer and all components.
b. Sawcut opening in exterior wall for new cooler/freezer entrance.
c. Remove existing condenser and pad.
d. Remove palm tree xxxxx
2. The following items are not included:
a. Storage or removal of any other equipment
1. The following items are i...
Design Builder's Representative. Design Builderdesignates the individual listed below as its Design Builder's Representative to provide direct interface with Owner with respect to Design Builder's responsibilities: Xxxx Xxxxxxx, Design Builder's Project Manager. Exhibit C- Project Assignment Page 3 of 4 1. Board Approval- 7/30/10 2. NTP- 7/31/20 3. Submittals – 7/31/20 – 8/14/20 4. Tank Procurement- 8/14/20 - 12/04/20, see qualifications sheet for further information.
Design Builder's Representative. Design Builderdesignates the individual listed below as its Design Builder's Representative to provide direct interface with Owner with respect to Design Builder's responsibilities: Xxxxxxx Xxxxxx, Design Builder's Project Manager. Exhibit C- Project Assignment Page 3 of 4 Exhibit C-1 – List of Contract Documents Page 1 of 1
1. Timely completion of the project is contingent upon receipt of BPS Building Official approval to begin new construction activities with the issuance of building permits to support the project completion schedules outlined in the Design Builder’s proposal.
2. It is understood that any additional work required by the BPS Building Official, not specifically identified in the GMP proposal, is excluded.
3. Removal of hazardous materials, if encountered, is excluded.
4. A project contingency allowance of $15,000.00, without fee markup, is included. Atlantis Electrical Systems LLC
1. Building 34 Conduit between top and bottom floors.
2. Installation of SCSC provided wall mount cabinet on 3/4” plywood in building 34 and building 9.
3. Install 3’ sleeves in new cabinets with plastic screw on bushings.
4. Install additional sleeves in existing CER, and CCs where necessary.
5. Install surge suppression duplex receptacles in new cabinets.
6. Install 3/4” conduit in buildings with exposed ceilings.
7. Install pull strings in all conduit.
8. Provide as built drawings with all conduit pathways.
Design Builder's Representative. The Design-Builder’s authorized representative is Dxx Xxxxxx. The Design-Builder’s Representative shall possess full authority to receive instructions from the Owner and to act on those instructions. The Design-Builder shall notify the Owner in writing of a change in the designation of the Design-Builder’s Representative.
Design Builder's Representative. 7.3.1 Design-Builder shall ensure that the Design-Builder’s Representative is present at the Site at all times reasonably necessary to ensure that Design-Builder is complying with its obligations under this Agreement.
7.3.2 Design-Builder will be deemed to have received any direction given to the Design-Builder’s Representative.
7.3.3 Design-Builder may replace the Design-Builder’s Representative in accordance with Section 7.4 of this Agreement.
