Design Conditions and Performance Requirements Sample Clauses

Design Conditions and Performance Requirements. The pumps shall be capable of operating continuously at minimum flow without damage to the pumping equipment. Total head and pump efficiency shall be designed in accordance with the Hydraulic Institute Standards, Centrifugal Pump Section. Flow velocities at the outlets of discharge nozzles of the feed pumps shall not exceed 20 feet per second.
Sample 1
AutoNDA by SimpleDocs
Design Conditions and Performance Requirements. The condenser shall be designed in accordance with HEI Standards for steam surface condensers. Where the HEI Standards and this section of the SOW are at variance, this section shall control. The condenser shall maintain the backpressure required by the steam turbine guaranteed rating while operating with circulating water temperatures based upon cooling tower performance under design ambient conditions as specified in the Performance Data and guarantees. The condenser shall be capable of maintaining the backpressure and exhaust temperature within the permissible limits set by the turbine manufacturer while experiencing continuous operation of the steam turbine bypass system at maximum expected flow. The condenser design shall be capable of condensing full steam production from the HRSG HP, IP, and LP sections and shall maintain condenser pressure within the turbine manufacturer limits for operation. Contractor shall determine all circulating water uplift forces that affect foundation design. The uplift forces shall be determined with the discharge valve of one circulating water channel closed or all the discharge valves at the outlet shell closed so that the inlet waterbox uplift forces are based on circulating water pump shutoff pressure.
Sample 1
Design Conditions and Performance Requirements. The design capacity of each pump shall be determined according to the required capacity of the system and pressure in deaerator at maximum continuous rating of the unit. The design capacity of each pump shall be 50% of the maximum plant expected condensate flow to the deaerators plus 5% margin. In order to prevent damage at low flow operation beyond normal wear and tear and to obtain sufficient cooling flow through the gland steam condenser; the condensate line shall be provided with recirculation line for a safe minimum flow back to condenser. Each pump shall be suitable for direct connection to a vertical motor driver. The pumps shall be designed to operate continuously over the pump operating range without cavitation. Contractor shall provide Owner with pump performance characteristic curves on which total developed head, brake horsepower, required NPSH, and efficiency are plotted as functions of volumetric flow rate between shut-off and run-out. Total developed head and pump efficiency shall be defined in accordance with the Hydraulic Institute Standards. Contractor shall obtain a manufacturer's guarantee for the performance of the pumping equipment. The tolerances on the guaranteed performance shall be in accordance with the Hydraulic Institute Standards. Pump head curve shall rise continuously from best efficiency head point to shut-off. The pump shut-off head shall fall between 120 to 135 percent of the total head at the best efficiency point. The pumps shall be of the same model, manufacturer, and identical in construction so that replacement parts are interchangeable. The pump seal shall be designed for seal water injection with seal water supplied from the common pump discharge header during pump operation. The first pump to start will run momentarily without seal water injection. Contractor shall provide one (1) vertical electric motor as driver for each condensate pump. Suction strainers for each pump shall be supplied. The unit shall be arranged to facilitate inspection and maintenance. Motor head unit and inner assembly shall be readily removable without disturbing the pump can.
Sample 1
Design Conditions and Performance Requirements. The pump suction specific speed shall be sufficient to prevent cavitation under the Operating Conditions. The structural integrity of pumps, drivers, and accessories shall not be impaired by flow reversal through a pump, resulting from failure of its driver, with its discharge valve wide open and the remaining pumps operating. The pumps shall be suitable for outdoor locations. The sources, descriptions, and chemical analysis of circulating water and water available for bearings, seals, and cooling shall be provided to the pump manufacturer by the Contractor. Each pump shall be direct connected to an electric motor driver. The electric motors shall be furnished with non-reverse ratchets. Contractor shall prepare the pump performance characteristic curve on which total developed head, brake horsepower, and efficiency are plotted as functions of volumetric flow rate between shut-off and run-out. The minimum submergence for no cavitation shall also be plotted between the minimum flow rate and run-out. Total developed head and pump efficiency shall be defined in accordance with the Hydraulic Institute Standards. Contractor shall prepare torque-speed curves from zero to rated pump speed. These shall include starting against a closed discharge valve. The system-operating mode shall be arranged to start each pump against a closed discharge valve, which will open automatically as the pump comes up to speed.
Sample 1
Design Conditions and Performance Requirements. Maximum average pipe velocity shall not exceed 10 fps. Pipe shall be designed to withstand internal pressures, both operating and transient. Minimum design pressure shall be higher than both the pressure corresponding to the shutoff head of the pump and the minimum design pressure specified in the applicable piping standard. The piping system shall be designed to withstand all external loads; both with the pipe empty and in combination with internal pressure. Buried portions of pipe shall be capable of resisting internal pressure without backfill in place. Depth of the earth cover shall prevent floating of the empty pipe when ground water level is at its maximum level, but will be a minimum of 3 feet deep where buried. Pipe installed under traffic areas shall be designed to withstand HS20-44 truck loading.
Sample 1
Design Conditions and Performance Requirements. Each cooling tower shall be designed to dissipate the thermal load of the turbine and other auxiliaries for one Power Block and to provide the cold water temperatures consistent with Section Design Conditions. The cooling tower design shall be of mechanical induced draft, multicell, counterflow. Arrangement and orientation of the cooling tower(s) shall take into account prevailing winds. Cooling towers shall be designed to operate using untreated water from Lake Pat Mayse. The towers (including fill and its support system) shalx xx xxxxgned to include necessary features to prevent damage from freezing during operation under any mode. A manual control bypass system shall be provided to bypass return water directly to the cooling tower basin under freezing conditions.
Sample 1

Related to Design Conditions and Performance Requirements

  • Continuity of Service and Performance Unless otherwise agreed in writing, the Parties shall continue to provide service and honor all other commitments under this Agreement during the course of a Dispute with respect to all matters not subject to such Dispute.

  • PAYMENT AND PERFORMANCE OF LIABILITIES The Borrowers shall pay each payment Liability when due (or when demanded, if payable on demand) and shall promptly, punctually, and faithfully perform each other Liability.

  • Portfolio Expense and Performance Data The Fund shall provide such data regarding each Portfolio’s expense ratios and investment performance as the Company shall reasonably request, to facilitate the registration and sale of the Variable Contracts. Without limiting the generality of the forgoing, the Fund shall provide the following Portfolio expense and performance data on a timely basis to facilitate the Company’s preparation of its annually updated registration statement for the Variable Contracts (and as otherwise reasonably requested by the Company), but in no event later than 75 calendar days after the close of each Portfolio’s fiscal year:

  • Payment of Indebtedness and Performance of Obligations The Borrower shall pay and discharge when due all lawful Indebtedness, obligations and claims for labor, materials and supplies or otherwise which, if unpaid, could reasonably be expected to (a) have a Material Adverse Effect on the Borrower or (b) give rise to the imposition of a Lien (other than a Permitted Lien) upon the property of the Borrower, unless and to the extent only that the validity of such Indebtedness, obligation or claim shall be contested in good faith and by appropriate proceedings diligently conducted by or on behalf of the Borrower, and provided that such reserve or other appropriate provision as shall be required in accordance with Applicable Accounting Principles shall have been made therefor.

  • Capacity and Performance (a) During the term hereof, the Executive shall serve the Company as its Vice President and Chief Operating Officer. In addition, and without further compensation, the Executive shall serve as a director of the Company, if so elected by the stockholders of the Company, and shall serve as a director of one or more of the Company’s Affiliates if so elected from time to time.

  • Payment and Performance of Obligations Pay and perform all material Obligations under this Agreement and the other Loan Documents, and pay or perform (a) all taxes, assessments and other governmental charges that may be levied or assessed upon it or any of its property, and (b) all other indebtedness, obligations and liabilities in accordance with customary trade practices; except to the extent that IPT or the Borrower is contesting any item described in clauses (a) or (b) of this Section 7.5 in good faith and is maintaining adequate reserves with respect thereto in accordance with GAAP.

  • Duties and Performance From time to time during the term of this Agreement, Consultant shall provide such advisory services relating to the Company's financial status and capital structure (the "SERVICES") to Company as Consultant and Company shall agree. In connection with the Services, Consultant may develop and communicate to Company certain business opportunities with entities known to Consultant; the Services may include various types of arrangements, including direct investment into Company.

  • Payment and Performance The Borrower will pay all amounts due under the Loan Documents in accordance with the terms thereof and will observe, perform and comply with every covenant, term and condition expressed or implied in the Loan Documents. The Borrower will cause each other Loan Party to observe, perform and comply with every such term, covenant and condition in any Loan Document.

  • Accuracy of Representations and Performance of Covenants The representations and warranties made by the Company in this Agreement were true when made and shall be true as of the Closing Date (except for changes therein permitted by this Agreement) with the same force and effect as if such representations and warranties were made at and as of the Closing Date. Additionally, the Company shall have performed and complied with all covenants and conditions required by this Agreement to be performed or complied with by the Company.

  • Guaranty of Payment and Performance Guarantor’s obligations under this Guaranty constitute an unconditional guaranty of payment and performance and not merely a guaranty of collection.

Time is Money Join Law Insider Premium to draft better contracts faster.