Measurement Data Sample Clauses

Measurement Data. 2.1 If the Service Provider fails to provide the Measurement Data for a Settlement Month by the corresponding Data Submission Deadline, or fails to provide any required corrections to the Measurement Data by the Corrected Data Submission Deadline, the Contract Payment for such Settlement Month shall be equal to zero.
Sample 1Sample 2
AutoNDA by SimpleDocs
Measurement Data. (a) Allocated Producers Data. Gatherer will make available to Producers, including through electronic access as available, information containing Producers’ previous Day’s volumes (in MMBTU) delivered to each Receipt Point, as well as daily Gas Lift Gas information for each Receipt Point. Gatherer will also provide Producers, including through electronic access as available, access to its preliminary daily measurement data for the Day that Dedicated Gas was actually received at each Receipt Point as allocated by the Dedicated Gas flow in MMBTU/Day to help Producers minimize Imbalances. All such information for a Day will be provided by Gatherer on or before forty-eight (48) hours after the end of such Day, unless Gatherer is unable to do so for reasons beyond its reasonable control, in which case Gatherer will provide Producers such data as soon as reasonably practicable under the circumstances.
Sample 1Sample 2
Measurement Data. Gatherer will make available to Producers, including through electronic access as available, information containing the previous Day’s volumes (MMBTU) and a spot flow rate in MMBTU/Day at the time of the latest poll of the measurement station. All such information for a Day will be provided by Gatherer on or before two (2) hours after the end of such Day, unless Gatherer is unable to do so for reasons beyond its reasonable control, in which case Gatherer will provide Producers such data as soon as reasonably practicable under the circumstances.
Sample 1Sample 2
Measurement Data. 18 deflection values measured at site with the small-plate light falling weight deflectometer, adjusted parameters, gauge ID, measuring method, sign and date, which the deflectometer stores in its data storing until its cancelling.
Sample 1
Measurement Data. To the extent provided to Buyer by the Downstream Facility and solely when Producer is the sole seller of Product to Buyer for transportation using the Buyer Capacity, Buyer shall provide, or cause to be provided, daily RoseRock Scada Tank/Meter data for receipts at Origin Points for prior day’s data. If requested by Producer, Buyer shall request the Downstream Facility provide, at Producer’s cost, access to real-time measurement data at the Origin Points, including volume, gravity, average flowing temperature, average flowing pressure and other reasonably requested and available measurement data.
Sample 1
Measurement Data. Carrier shall provide Producer, at no cost to Producer, a port to receive all measurement data generated at each individual Receipt Point and Delivery Point and Carrier will utilize this data to manage the nomination, allocation and billing procedures related to Carrier’s services provided hereunder. In addition, all data collected in Carrier’s SCADA system shall be made available to Producer in electronic form on a continuous, real-time basis. (a) Carrier will provide direct electronic access to communications port(s) on Carrier’s EFMs to obtain real time and audit trail data (thirty-five (35) Day hourly average measurement data, alarms, and events). (b) If Producer is unable to obtain historical measurement data from any meter, Carrier will provide such data in electronic format. (c) Carrier and Producer will mutually agree upon a reporting method for volumes of vertical well Crude Oil. (d) Carrier shall install a SCADA system to collect and monitor Central Battery LACT and tank level data. All data collected will be made available to Producer via direct electronic access.
Sample 1
Measurement Data. Gatherer, or its designee, shall be solely responsible for obtaining all necessary measurement data concerning Gatherer’s receipts of Shipper’s Gas at the Point of Receipt hereunder. The quantity of Gas measured at the Point of Measurement shall be measured in accordance with the provisions of Article IV of Exhibit C, subject to the receipt of all necessary regulatory approvals.
Sample 1
AutoNDA by SimpleDocs
Measurement Data. The standard measure of area in the real estate market in Mexico is the square meter (m2), while in the United States the standard measure is the square foot (sq. ft.). Unless otherwise specified, all units of area shown in this document are expressed in terms of square feet. Ten square feet is equal to approximately 0.929 square meters. Certain percentages and totals may not sum due to rounding. The CBFIs have not been, nor will be, registered under the Securities Act, any other U.S. federal or state or non-U.S. securities laws or the laws of any non-U.S. jurisdiction other than Mexico. The CBFIs will not be registered under the Securities Act in reliance upon the exemption contained in section 4(a)(2) of the Securities Act and in Rule 506 of Regulation D or Regulation S promulgated thereunder or other applicable exemptions promulgated under the Securities Act. Holders in the United States may only participate in the subscription if they are “accredited investors” as defined under Regulation D under the Securities Act and Holders outside the United States only if they are non- U.S. persons and in reliance on Regulation S under the Securities Act.
Sample 1

Related to Measurement Data

  • Measurement Should the State terminate this contract as herein provided, no fees other than fees due and payable at the time of termination shall thereafter be paid to the Engineer. In determining the value of the work performed by the Engineer prior to termination, the State shall be the sole judge. Compensation for work at termination will be based on a percentage of the work completed at that time. Should the State terminate this contract under paragraph (4) or (5) above, the Engineer shall not incur costs during the thirty-day notice period in excess of the amount incurred during the preceding thirty days.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.

  • Performance Measurement The Uniform Guidance requires completion of OMB-approved standard information collection forms (the PPR). The form focuses on outcomes, as related to the Federal Award Performance Goals that awarding Federal agencies are required to detail in the Awards.

  • Temperature Measurement Temperature will be measured by the nearest automatic Melbourne Bureau of Meteorology Monitoring Station for example (but not limited to): Melbourne, Moorabbin, Dunns Hill, Melbourne Airport, Frankston, and Point Xxxxxx. At the commencement of each project, the onsite management and employee representatives shall agree which is to be the applicable automatic weather monitoring station.

  • Measurements Units set out in SI (metric) are the governing units for the purposes of this Contract. Units set out in Imperial measurement in parentheses beside their SI (metric) equivalent are for reference only and in the event of a conflict between SI (metric) and Imperial measurement herein, SI (metric) shall prevail.

  • Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.

  • Performance Measure Grantee will adhere to the performance measures requirements documented in

  • Measurement Period In this Agreement, unless the contrary intention appears, a reference to:

  • Measuring EPP parameters Every 5 minutes, EPP probes will select one “IP address” of the EPP servers of the TLD being monitored and make an “EPP test”; every time they should alternate between the 3 different types of commands and between the commands inside each category. If an “EPP test” result is undefined/unanswered, the EPP service will be considered as unavailable from that probe until it is time to make a new test.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!