Overtime Scheduling and Call-Out Sample Clauses

Overtime Scheduling and Call-Out. The Department shall offer all non-emergency overtime opportunities (except for work in progress) to covered employees on a strict seniority basis. If it is necessary to hold an officer over from a prior shift or to call an officer in early from the next shift, selection will be requested by seniority. If no officer volunteers, and it should be necessary to order an officer to stay or report in early, then overtime will be ordered on the basis of reverse seniority. However, in no circumstances shall the same officer be mandated to stay and report in early, thereby causing the officer to work in excess of two continuous shifts. Seniority may be bypassed if assignments require special skill, ability and experience or involve work in progress. Should a violation of this Section be established through the grievance procedure, the sole remedy available to the aggrieved employee(s), absent a showing of repeated, intentional violation of this Article by the involved supervisor or manager, shall be to provide that employee(s) with the next available, reasonably similar overtime assignment(s).
Sample 1Sample 2See All (4)
AutoNDA by SimpleDocs

Related to Overtime Scheduling and Call-Out

  • Overtime Scheduling (A) It is the intent of the City, consistent with efficient and effective operation of the Division of Police, to distribute in an equitable manner, all pre-scheduled overtime among all members. Recognition will be given to the qualifications of the members and the requirements placed on the City by any third party funding sources. Any complaints by members that pre-scheduled overtime is not being equitably distributed among all qualified members as described above may be brought by the Lodge directly to the Chief's attention at Step 3 of the Grievance Procedure and shall also be a proper subject for discussion in a Labor Relations Committee meeting. Inability to work a prescheduled overtime assignment due to illness or death in the family or injury will not require the member to charge such absence against sick leave or injury leave.

  • Training and Support Through the Solution, the Contractor shall provide all consulting, training, and support to the Customer and FL[DS] to ensure successful implementation of the Solution and ongoing support as necessary and as defined by FL[DS] to include, but not be limited to:

  • Training and Technical Assistance COALITION will notify PROVIDER of the availability of training, technical assistance, and other targeted assistance in support of the provision of quality VPK services. COALITION will offer technical assistance for providers on probation. The technical assistance will be designed to facilitate the development and implementation of an improvement plan. The technical assistance will be offered in a manner and schedule prescribed by the COALITION or school district.

  • Innovative Scheduling Schedules which are inconsistent with the Collective Agreement provisions may be developed in order to improve quality of working life, support continuity of resident care, ensure adequate staffing resources, and support cost-efficiency. The parties agree that such innovative schedules may be determined locally by the Home and the Union subject to the following principles:

  • Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Purchaser may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in A2. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.

  • Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until he/she has received proper training and instruction.

  • Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.

  • Training and Promotion a. The contractor will assist in locating, qualifying, and increasing the skills of minorities and women who are applicants for employment or current employees. Such efforts should be aimed at developing full journey level status employees in the type of trade or job classification involved.

  • METERING AND BILLING Metering requirements and billing procedures shall be set forth in the AEC rate schedule(s) applicable to the electric service account assigned to the location where the Generating Facility is connected.

  • Cutting, Patching, and Fitting The Contractor shall do all cutting, patching, and fitting of the Work that may be required to make its several parts come together properly and fit.

Time is Money Join Law Insider Premium to draft better contracts faster.