Standards, Codes, Rules, Regulations Sample Clauses

Standards, Codes, Rules, Regulations. Each unit shall conform to the Pennsylvania Motor Vehicle Code. Each unit shall comply with all current applicable Federal Motor Vehicle Safety Standards, Federal and Pennsylvania Exhaust Emission and Noise Standards and Environmental Protection Agency (EPA) and Occupational Safety and Health Administration (OSHA) requirements, with appropriate decals stating compliance. The equipment shall be manufactured as per good engineering practice. Standard manufacturing practices and tolerances shall be in accordance with the latest codes, standards and practices of the following professional organizations: RE: American Institute of Steel Construction (AISI) American National Standards Institute (ANSI) American Society of Mechanical Engineers (ASME) American Society of Testing and Materials (ASTM) American Trucking Association (ATA) American Welding Society (AWS) Battery Council International (BCI) British Standards Institute (BSI): Limits and Fits International Standards Organization (ISO) Industrial Fastener Institute (IFI) National Truck Equipment Association (NTEA) Society of Automotive Engineers (SAE) Steel Structure Painting Council (SSPC) Truck Body and Equipment Association, Inc. (TBEA) Maximum Gross Vehicle Weight Ratings (GVWR) will be subject to the appropriate Districts review. The GVWR shall be identified in the cab or on the door as the final complete certification label (Minimum rating). The Gross Combined Weight Rating (GCWR) shall be furnished and identified by decal in the cab or on the door to indicate approved weight which can be towed. Each unit shall bear the latest applicable Pennsylvania Official Inspection Sticker as required for permanent license plates by Pennsylvania State Inspection Laws. It is recommended that bidders forward a copy of the entire specification to all component manufacturers to communicate the Department’s Requirement. All Original Equipment Manufacturers (OEMs) that participate have full responsibility in fulfilling their contract obligations to the main vendor.
AutoNDA by SimpleDocs

Related to Standards, Codes, Rules, Regulations

  • RULES & REGULATIONS The Exhibitor must comply with the requirements of all Authorities and where applicable with all rules and regulations issued by the owner of the Venue in force at the time of the Exhibition. The Exhibitor undertakes to comply with the obligations and duties contained or referred to in the Contract including (without limitation) those contained or to be contained in the Exhibitors’ Manual. Exemptions from any of these obligations and duties may be granted at the Organisers’ discretion. No exemption given by the Organisers will be effective unless in writing. The Contract comprises these Terms and Conditions, the Exhibition Space Contract and the Exhibitors’ Manual) except as varied in writing signed by the parties.

  • General Data Protection Regulation 10.1 Protecting your personal information is incredibly important to Excalibur. Our privacy policy which sets out how we do this is available here: xxxxx://xxx.xxxxxxxxxxxxxx.xx.xx/gdpr-policy/. This policy explains the information that we hold, how we use it, and how long we keep it for. Please take a few minutes to read it.

  • Laws, Rules and Regulations You agree to comply with all existing and future operating procedures used by the Bank for processing of transactions. You further agree to comply with, and be bound by, all applicable state or federal laws, rules, regulations, orders, guidelines, operating circulars and pronouncements, affecting checks and drafts, including, but not limited to, all rules and procedural guidelines established by the Board of Governors of the Federal Reserve and the Electronic Check Clearing House Organization ("ECCHO") and any other clearinghouse or other organization in which Bank is a member or to which rules Bank has agreed to be bound. These procedures, rules, and regulations (collectively the "Rules") and laws are incorporated herein by reference. In the event of conflict between the terms of this Agreement and the Rules, the Rules will control.

  • Contract Work Hours and Safety Standards Act The following clauses apply to any Federal-aid construction contract in an amount in excess of $100,000 and subject to the overtime provisions of the Contract Work Hours and Safety Standards Act. These clauses shall be inserted in addition to the clauses required by 29 CFR 5.5(a) or 29 CFR 4.6. As used in this paragraph, the terms laborers and mechanics include watchmen and guards.

  • Safety Rules 5.01 The safety rules of the State having jurisdiction shall be observed by the parties hereto. It is recognized that the Employer has the exclusive responsibility for providing a safe and healthful workplace. To assist the Employer in maintaining an effective and continuing safety program, a permanent Joint Safety Committee shall be established, consisting of two (2) members from the Union and two (2) members from the Employers, who shall meet at regular times to administer educational instructions, investigate serious accidents, and to draft appropriate safety rules. Such rules as adopted by this committee, shall become a part of this Agreement.

  • Safety Standards Performance of the Contract for all commodities or contractual services must comply with requirements of the Occupational Safety and Health Act and other applicable State of Florida and federal requirements.

  • General Regulations A. Excessively loud speakers and sound displays are not permitted, and BAC Productions shall have the right to reject any exhibit which does not, in its sole, and reasonable opinion, conform to the general tenor of the show.

  • COMPLIANCE WITH THE CONTRACT WORK HOURS AND SAFETY STANDARDS ACT (1) Overtime requirements. No contractor or subcontractor contracting for any part of the contract work which may require or involve the employment of laborers or mechanics shall require or permit any such laborer or mechanic in any workweek in which he or she is employed on such work to work in excess of forty hours in such workweek unless such laborer or mechanic receives compensation at a rate not less than one and one-half times the basic rate of pay for all hours worked in excess of forty hours in such workweek.

  • Technical Regulations 1. The rights and obligations of the Parties in respect of technical regulations, standards and conformity assessment shall be governed by the WTO Agreement on Technical Barriers to Trade.

  • Health and Safety Standards Contractor shall abide by all health and safety standards set forth by the State of California and/or the County of Xxxxxx pursuant to the Injury and Illness Prevention Program. If applicable, Contractor must receive all health and safety information and training from County.

Time is Money Join Law Insider Premium to draft better contracts faster.